Home > Brother > Sewing Machine > Brother Super Galaxie 2 Manual

Brother Super Galaxie 2 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Brother Super Galaxie 2 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 331 Brother manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							ERROR MESSAGES
    349
    Appendix
    9
    This message appears when 
    there are not enough colors in 
    the custom thread table, to 
    display the color scheme you 
    have selected to display.
    In this case, set more colors 
    in the custom thread table 
    (See page 278), or select 
    less colors in the color 
    shuffling function. (See 
    page 283.)
    This message appears when 
    there are not enough colors in 
    the thread table, to display 
    the color scheme effect you 
    have selected.
    In this case, select another 
    effect or the custom thread 
    table (300 color palette) or 
    less colors in the Color 
    Shuffling function. (See 
    page 283.)
    If there are not enough 
    number of colors set in the 
    custom thread table, set more 
    colors in the table. (See 
    page 278.)
    This message is displayed 
    when the automatic needle 
    threading button is pushed 
    while twin needle sewing is 
    set.
    This message is displayed 
    when the “Start/Stop” button 
    is pressed before the edge of 
    the fabric is detected. To 
    detect the edge of the fabric 
    using the built-in camera, 
    press  , raise the 
    presser foot, and then 
    perform the operation again. 
    (see page 148)This message is displayed 
    when the built-in camera 
    cannot detect the edge of the 
    fabric.
    If this message appeared 
    after sewing has reached 1 to 
    2 cm (about 3/8 to 3/4 inch) 
    from the edge of the fabric, 
    refer to step 
    m in “Edge 
    Sewing” on page 154.
    If this message appeared 
    during edge sewing, the edge 
    of the fabric cannot be 
    detected by the built-in 
    camera. Press  , raise 
    the presser foot, raise the 
    needle if it is lowered, and 
    then perform the procedure 
    described in “Edge Sewing” 
    on page 150 starting from 
    step 
    f.
    If this error message appears 
    again, sew without using 
    edge sewing function.
    This message appears when 
    you try to save more than 100 
    camera image or settings 
    screen image files in the USB 
    media. In this case, delete a 
    file from the USB media or 
    use different USB media. 
    (See page 39 and 87)
    This message appears when 
     or   is 
    pressed to delete the settings 
    for a utility stitch. To delete 
    the selected settings, press 
    .
    This message is displayed 
    when an unusable 
    embroidery card is inserted.  
    						
    							ERROR MESSAGES
    350
    This message is displayed 
    when the “Reverse/
    Reinforcement Stitch” button 
    is pushed while the 
    embroidery unit is attached.
    This message is displayed 
    when the foot controller is 
    pressed while the embroidery 
    unit is attached and machine 
    is set up for embroidering.
    This message is displayed 
    when the patterns you are 
    editing take up too much 
    memory, or if you are editing 
    too many patterns for the 
    memory. 
    This message is displayed 
    when a key on the LCD 
    display is touched while the 
    needle is in the down 
    position. This message is displayed 
    when there are too many 
    characters and the curved 
    character configuration is 
    impossible. 
    This message is displayed 
    when the machine is in 
    embroidery mode, and the 
    character pattern 
    combination is too large to fit 
    in the embroidery frame. 
    This message is displayed 
    when the machine is in 
    embroidery mode and the 
    combined character pattern is 
    too large for the embroidery 
    frame. You can rotate the 
    pattern 90 degrees and 
    continue combining 
    characters. 
    This message is displayed 
    when the machine is in 
    embroidery mode and the 
    embroidery unit tries to 
    initialize while the embroidery 
    frame is attached. 
    This message is displayed 
    when the machine is ready to 
    sew an embroidery pattern, 
    and the “Start/Stop” button is 
    pushed while the embroidery 
    frame is not attached.  
    						
    							ERROR MESSAGES
    351
    Appendix
    9
    This message is displayed 
    when the machine is in 
    embroidery edit mode, and 
    you try to use an editing 
    function when the pattern is 
    not completely within the red 
    outline. 
    This message is displayed 
    when you try to save a 
    copyright protected pattern to 
    USB media/Computer. 
    According to copyright laws, 
    patterns that are illegal to 
    reproduce or edit cannot be 
    saved to USB media or 
    computer. If this message 
    displays, save the pattern in 
    the machine’s memory. 
    This message is displayed 
    when the machine is in 
    embroidery mode and the 
    small frame is attached, and 
    the selected pattern does not 
    fit in the small frame. 
    This message appears when 
    embroidery frame (small) is 
    attached while aligning the 
    embroidery position using the 
    built-in camera.
    This message is displayed 
    when  is pressed 
    when changing thread colors.
    This message appears if the 
    machine is turned off while 
    sewing, then turned on again. 
    Press   to return the 
    machine to the condition 
    (pattern position and number 
    of stitches) when it was 
    turned off. Follow the 
    procedure described in “If the 
    Thread Breaks During 
    Sewing” on page 230 to align 
    the needle position and sew 
    the remainder of the pattern.This message is displayed 
    when the “Start/Stop” button 
    is pushed and the machine is 
    in embroidery mode, but the 
    embroidery unit is not 
    attached.
    This message is displayed 
    when replacing the 
    embroidering bobbin thread.
    This message is displayed 
    when rotating a saved 
    combined pattern in the 
    Embroidery screen.
    This message is displayed 
    when the embroidery frame is 
    attached. 
    						
    							ERROR MESSAGES
    352
    This message is displayed 
    when the machine failed to 
    recognize the embroidery 
    positioning mark.
    - Confirm that the embroidery positioning mark is in the 
    selected area. If problem 
    persists, see page 215 to 
    reposition mark.
    - Machine failed to recognize 
    printed positioning mark. 
    Set “Page Scaling” to “None 
    (100%)”, and try printing the 
    embroidery positioning 
    mark again. (see page 226)
    This message is displayed 
    when the machine has 
    recognized the embroidery 
    position mark. Remove the 
    embroidery positioning 
    sticker and press   to 
    continue. To remove the 
    embroidery positioning 
    sticker more easily, press  . (see page 215)
    This message appears when 
    the built-in camera is being 
    used to align the embroidery 
    position, but the embroidery 
    positioning sticker is too near 
    an edge or the pattern 
    extends from the embroidery 
    frame. Change the 
    positioning of the embroidery 
    position sticker, and then try 
    aligning the position again. 
    See page 208.
    This message is displayed 
    when the upper thread is 
    broken or not threaded 
    correctly, and the “Start/Stop” 
    button or the “Reverse/ 
    Reinforcement Stitch” button 
    is pressed. 
    This message is displayed 
    when the “Presser Foot Lifter” 
    button is pushed while the 
    presser foot lever is raised/
    the needle is lowered.This message is displayed 
    when the “Start/Stop” button 
    is pushed to sew Utility 
    stitches or Character/
    Decorative stitches while the 
    foot controller is connected. 
    (This message does not 
    appear when embroidering).
    This message is displayed 
    when the “Start/ Stop” button 
    is pushed while the machine 
    is in embroidery edit mode 
    and a pattern is being edited. 
    This message is displayed 
    when there is no stitch or 
    embroidery pattern selected 
    and the “Start/Stop” button or 
    the “Reverse/Reinforcement 
    Stitch” button is pressed. 
    This message is displayed 
    when the bobbin thread is 
    running out. 
    This message is displayed 
    when the memory is full and 
    the stitch or pattern cannot be 
    saved.  
    						
    							ERROR MESSAGES
    353
    Appendix
    9
    This message is displayed 
    when the machine is 
    retrieving a previously saved 
    pattern while in embroidery 
    edit mode. 
    This message is displayed 
    when, after selecting a 
    pattern, , , or   is 
    pressed and the pattern is 
    about to be deleted. 
    This message is displayed 
    when the bobbin is being 
    wound, and the motor locks 
    because the thread is 
    tangled, etc. 
    This message is displayed 
    when there is a possibility 
    that the data for the selected 
    pattern is corrupted.
    This message is displayed 
    when the buttonhole lever is 
    down, a stitch other than a 
    buttonhole is selected, and 
    the “Start/ Stop” button or the 
    “Reverse/Reinforcement 
    Stitch” button is pushed. This message is displayed 
    when the embroidery unit is 
    attached and the power is 
    turned on with the needle in 
    the down position. 
    This message is displayed 
    when the selected stitch is 
    not available for the specific 
    function.
    This message is displayed 
    when you try to recall or save 
    a pattern while no USB media 
    is loaded.
    This message is displayed 
    when you try to use 
    incompatible media. 
    						
    							ERROR MESSAGES
    354
    This message is displayed 
    when you attempt to select a 
    pattern after the USB media 
    in which the pattern is saved 
    has been changed.
    This message is displayed 
    when an error occurs with the 
    USB media.
    This message is displayed 
    while the USB media is 
    transmitting.
    This message is displayed 
    when the memory is full and a 
    pattern must be deleted.
    This message is displayed 
    when a button, such as the 
    “Start/Stop” button, is pushed 
    while the presser foot is 
    raised.This message is displayed if 
    some malfunction occurs.
    This message is displayed 
    when you try to use 
    incompatible USB media.
    For a list of compatible USB 
    media, visit “ http://
    solutions.brother.com ”.
    This message is displayed 
    when it seems that the upper 
    thread has not been threaded 
    correctly.
    This message is displayed 
    when  is pressed 
    (the presser foot is raised).
    This message is displayed 
    when the file size exceeds 
    the data capacity of the 
    machine. 
    Confirm the file size and 
    format. (see page 40.) 
    						
    							ERROR MESSAGES
    355
    Appendix
    9
    ■Alarm Sounds 
    If the operation was performed incorrectly, an alarm 
    sounds to indicate that an error occurred. If the 
    operation was performed correctly, the machine 
    beeps to confirm the operation.
     
    This message appears if the 
    file format is incompatible 
    with this machine. Check the 
    list of compatible file formats. 
    (see page 40.)
    This message is displayed 
    when the image is deleted.
    This message is displayed 
    when you press 
     in the screen 
    other than the Utility Stitch, or 
    press   in the 
    screen other than the Utility 
    Stitch or Character/
    Decorative Stitch.
    Memo
     To cancel the operation beep or to change  the volume, press  , display screen 
    3/8, and then change the setting for 
    “Speaker”. See page 36 for more details.  
    						
    							SPECIFICATIONS
    356
    SPECIFICATIONS
    * Please be aware that some specifications may change without notice.
    ItemSpecification
    Sewing Machine 
    (Box 1 of 3) Dimensions of machine
    Approx. 61.5 cm (W) × 33.2 cm (H)  × 27.0 cm (D) (approx. 
    24-7/32 inches (W)  × 13-5/64 inches (H)  × 10-5/8 inches (D))
    Dimensions of box Approx. 68.5 cm (W) × 47.0 cm (H)  × 39.0 cm (D) (approx. 
    26-31/32 inches (W)  × 18-1/2 inches (H)  × 15-11/32 inches 
    (D))
    Weight of machine Approx. 15 kg (approx. 33 lb)
    Weight of box (for shipping) Approx. 19 kg (approx. 42 lb)
    Sewing speed  70 to 1000 stitches per minute 
    Needles  Home sewing machine needles (HA × 130) 
    Accessory Box
    (Box 2 of 3) Dimensions of box
    Approx. 68.5 cm (W) × 15.2 cm (H)  × 39.4 cm (D) (approx. 
    26-31/32 inches (W)  × 6 inches (H)  × 15-33/64 inches (D))
    Weight of box (for shipping) Approx. 5 kg (approx. 11 lb)
    Embroidery Unit 
    (Box 3 of 3) Dimensions of embroidery unit Approx. 51.0 cm (W) 
    × 13.9 cm (H)  × 46.2 cm (D)  (approx. 
    20-5/64 inches (W)  × 5-15/32 inch (H)  × 18-3/16 inches (D))
    Dimensions of machine with 
    embroidery unit attached  Approx. 81.6 cm (W) 
    × 33.2 cm (H)  × 46.2 cm (D) (approx. 
    32-1/8 inches (W)  × 13-5/64 inches (H) ×  18-3/16 inches (D))
    Dimensions of box Approx. 68.5 cm (W) × 62.2 cm (H)  × 23.6 cm (D) (approx. 
    26-31/32 inches (W)  × 24-31/64 inches (H) ×  9-19/64 inches 
    (D))
    Weight of embroidery unit Approx. 4 kg (approx. 9 lb)
    Weight of box (for shipping) Approx. 13 kg (approx. 29 lb)
    Total Shipping Weight (Combination of all 3 boxes complete) Approx. 41 kg (approx. 90 lb) 
    						
    							UPGRADING YOUR MACHINE’S SOFTWARE
    357
    Appendix
    9
    UPGRADING YOUR MACHINE’S SOFTWARE
    You can use USB media or a computer to upgrade software for your sewing machine.
    When an upgrade program is available on “ http://solutions.brother.com ”, please download the files 
    following the instructions on the website and steps below.
    Upgrade Procedure Using USB 
    Media
    aWhile pressing the “Automatic Threading” 
    button, turn the main power to ON.
    →The following screen will appear on the LCD.
    bPress .
    cInsert the USB media into the primary (top) 
    USB port on the machine. The media device 
    should only contain the upgrade file.
    aPrimary (top) USB port for media
    b USB media
    dPress .
    →The upgrade file is loaded.
    Note
     When using USB media to upgrade the software, check that no data other than the upgrade file is 
    saved on the USB media being used before starting to upgrade.
    Note
     The access lamp will begin blinking after inserting USB media, and it will take about 5 
    to 6 seconds to recognize the media. (Time 
    will differ depending on the USB media).
    Note
     If an error occurs, a red text error message will appear. When the installation is 
    performed successfully, following message 
    will appear. 
    						
    							UPGRADING YOUR MACHINE’S SOFTWARE
    358
    eRemove the USB media, and turn the 
    machine off and on again.
    Upgrade Procedure Using 
    Computer
    aWhile pressing the “Automatic Threading” 
    button, turn the main power to ON.
    →The following screen will appear on the LCD.
    bPress .
    cPlug the USB cable connector into the 
    corresponding USB ports for the computer 
    and for the machine.
    →“Removable Disk” will appear in “Computer (My 
    computer)”.
    dCopy the upgrade file to “Removable Disk”.
    →The following message will appear.
    eWhen the message disappears, press 
    .
    →The upgrade file is loaded.
    fUnplug the USB cable, and turn the 
    machine off and on again.
    Note
     If an error occurs, a red text error message 
    will appear. When the installation is 
    performed successfully, following message 
    will appear. 
    						
    All Brother manuals Comments (0)

    Related Manuals for Brother Super Galaxie 2 Manual