Brother Super Galaxie 2 Manual

CHANGING THE NEEDLE
Getting Ready
69
1
About the Needle
The sewing machine needle is probably the most important part of the sewing machine. Choosing the 
proper needle for your sewing project will result in a beautiful finish and fewer problems. Below are some 
things to keep in mind about needles.
 The smaller the needle number, the finer the needle. As the numbers increase, the needles get thicker.
 Use fine needles with lightweight fabrics, and thicker needles with heavyweight fabrics.
 To avoid...

CHANGING THE NEEDLE
70 

Chapter 2
Sewing Basics
SEWING .............................................................................................. 72
Sewing a Stitch ........................................................................................................ 72
■Using the Foot Controller ................................................................................................ 73
Sewing Reinforcement Stitches ............................................................................... 74
Sewing Curves...

SEWING
72
SEWING
Sewing a Stitch
aTurn the main power to ON and press  to display the utility stitches, and 
push the “Needle Position” button to raise 
the needle.
bPress the key of the stitch you want to sew.
→ The symbol of the correct presser foot will be 
displayed in the upper left corner of the LCD screen.
cInstall the presser foot (“CHANGING THE 
PRESSER FOOT” on page 65).
dSet the fabric under the presser foot. Hold 
the fabric and thread in your left hand, and 
rotate the handwheel to set the...

SEWING
Sewing Basics
73
2
fAdjust the sewing speed with the speed 
control slide.
* You can use this slide to adjust sewing speed during sewing.
a Slow
b Fast 
gPress the “Start/Stop” button to start 
sewing.
* Guide the fabric lightly by hand.
hPress the “Start/Stop” button again to stop 
sewing.
iPress the “Thread Cutter” button to trim 
the upper and lower threads.
→The needle will return to the up position 
automatically.
jWhen the needle has stopped moving, raise 
the presser foot and remove the...

SEWING
74
aPull the retractable cord out from the foot 
controller to the desired length, and then 
insert the foot controller plug into its jack 
on the machine.
aFoot controller
b Foot controller jack
bSlowly depress the foot controller to start 
sewing.
cRelease the foot controller to stop the 
machine.
Sewing Reinforcement Stitches 
Reverse/reinforcement stitches are generally 
necessary at the beginning and end of sewing. You 
can use the “Reverse/Reinforcement Stitch” button 
to sew...

SEWING
Sewing Basics
75
2
Changing Sewing Direction 
Stop the machine. Leave the needle in the fabric, 
and press the “Presser Foot Lifter” button to raise 
the presser foot. Using the needle as a pivot, turn 
the fabric so that you can sew in the new 
direction. Press the “Presser Foot Lifter” button to 
lower the presser foot and start sewing.
The pivot setting is useful when changing the 
sewing direction. When the machine is stopped at 
the corner of the fabric, the machine stops with the 
needle in...

SEWING
76
■If the Fabric does not Feed
If the fabric does not feed when starting to sew or 
when sewing thick seams, press the black button on 
the left side of presser foot “J”. 
aRaise the presser foot. 
bWhile keeping the black button on the left 
side of presser foot “J” pressed in, press the 
“Presser Foot Lifter” button to lower the 
presser foot.
cRelease the black button.
→ The presser foot remains level, enabling the fabric to 
be fed.
Sewing Hook-and-Loop Fastener
Make sure that the needle...

SEWING
Sewing Basics
77
2
Sewing Stretch Fabrics
First, baste together the pieces of fabric, and then 
sew without stretching the fabric.
In addition, a better result can be achieved by 
using thread for knits or a stretch stitch.
aBasting stitching
Memo
 For best results when sewing stretch fabrics, 
decrease the pressure of the presser foot 
(“Using the Machine Setting Mode Key” on 
page 35). 

STITCH SETTINGS
78
STITCH SETTINGS
When you select a stitch, your machine automatically selects the appropriate stitch width, stitch length, 
and upper thread tension. However, if needed, you can change any of the individual settings.
Setting the Stitch Width
Follow the steps below when you want to change 
the zigzag stitch pattern width.
Example:
Press   to narrow the zigzag stitch pattern 
width. 
→The value in the display gets smaller.
Press   to widen the zigzag stitch pattern width. 
→The value in...