Home > Brother > Sewing Machine > Brother Super Galaxie 2 Manual

Brother Super Galaxie 2 Manual

Here you can view all the pages of manual Brother Super Galaxie 2 Manual. The Brother manuals for Sewing Machine are available online for free. You can easily download all the documents as PDF.

Page 61

UPPER THREADING
Getting Ready
59
1
iPass the thread through the needle bar 
thread guide (marked “6”) by holding the 
thread with both hands and guiding it as 
shown in the illustration.
aNeedle bar thread guide
jPress the “Presser Foot Lifter” button to 
lower presser foot.
kPass the thread through the thread guide 
disks (marked “7”). Make sure that the 
thread passes through the groove in the 
thread guide.
aGroove in thread guide
lPull the thread up through the thread cutter 
to cut the thread, as...

Page 62

UPPER THREADING
60
nCarefully pull the end of the thread that was 
passed through the eye of the needle.
* If a loop was formed in the thread passed through the eye of the needle, carefully pull on the loop of 
thread through to the back of the needle.
oPull out about 10-15 cm (approx. 4-6 
inches) of the thread, and then pass it under 
the presser foot toward the rear of the 
machine.
→Raise the presser foot lever if the presser foot is 
lowered.
a About 10-15 cm (approx. 4-6 inches)
Using the Twin...

Page 63

UPPER THREADING
Getting Ready
61
1
aPress   and install the twin needle 
(“CHANGING THE NEEDLE” on page 67).
bThread the machine for the first needle 
according to the procedure for threading a 
single needle (“Upper Threading” on 
page 57).
cPass the thread through the needle bar 
thread guides on the needle bar, then 
thread the needle on the left side manually.
aNeedle bar thread guide
dPull up the supplemental spool pin and set it 
in the up position.
aSupplemental spool pin
ePlace the additional...

Page 64

UPPER THREADING
62
hContinue threading however do not pass 
the thread in the needle bar thread guide 
“6” on the needle bar. Thread the needle on 
the right side. 
aNeedle bar thread guide
iPress .
jSelect a stitch pattern. (Example:  )
* Refer to the “STITCH SETTING CHART” at the end 
of this manual for the proper stitch to use with 
presser foot “J”. 
→ The selected stitch is displayed.
kPress   to select the twin needle mode.
aSingle needle/twin needle setting
→  appears.
lStart sewing.
Sample of...

Page 65

UPPER THREADING
Getting Ready
63
1
Using the Spool Stand
The included spool stand is useful when using 
thread on spools with a large diameter (cross-
wound thread). This spool stand can hold two 
spools of thread.
■Using the Spool Stand
 Be sure to use a spool cap that is slightly larger 
than the spool.
If the spool cap that is used is smaller or much 
larger than the spool, the thread may catch and 
sewing performance may suffer.
 When using thread on a thin spool, place the  included spool felt on...

Page 66

UPPER THREADING
64
cPull the thread off the spool. Pass the thread 
from the back to the front through the 
thread guides at the top.
dPass the thread through the machines 
thread guide from the right to the left.
aThread guide
eThread the machine according to the steps 
f to o of “Upper Threading” on page 57.
Using Threads that Unwind 
Quickly
■Using the Spool Net
If using transparent nylon monofilament thread, 
metallic thread, or other strong thread, place the 
included spool net over the spool before...

Page 67

CHANGING THE PRESSER FOOT
Getting Ready
65
1
CHANGING THE PRESSER FOOT
Removing the Presser Foot
Press  →   →   → 
  →    in this order to display a 
video example of the operation on the LCD (see 
page 46). Follow the steps explained below to 
complete the operation.
aPress the “Needle Position” button to raise 
the needle.
bPress .
* If the message “OK to automatically lower the  presser foot?” appears on the LCD screen, press OK 
to continue.
→ The entire screen becomes white, and all keys and...

Page 68

CHANGING THE PRESSER FOOT
66
bPress   to unlock all keys and 
buttons.
cRaise the presser foot lever.
Attaching the Walking Foot
The walking foot holds the fabric between the 
presser foot and the feed dogs to feed the fabric. 
This enables you to have better fabric control 
when sewing difficult fabrics (such as quilted 
fabrics or velvet) or fabrics that slip easily (such as 
vinyl, leather, or synthetic leather).
aFollow the steps in “Removing the Presser 
Foot” on the previous page.
bLoosen the screw...

Page 69

CHANGING THE NEEDLE
Getting Ready
67
1
CHANGING THE NEEDLE
Press  →   →    → 
  →    in this order to display a 
video example of the operation on the LCD (see 
page 46). Follow the steps explained below to 
complete the operation.
aPress the “Needle Position” button to raise 
the needle.
bPress .
* If the message “OK to automatically lower the  presser foot?” appears on the LCD screen, press OK 
to continue. →
The entire screen becomes white, and all keys and 
operation buttons are locked.
cUse the...

Page 70

CHANGING THE NEEDLE
68
dWith the flat side of the needle facing the 
back, insert the new needle all the way to 
the top of the needle stopper (viewing 
window) in the needle clamp. Use a 
screwdriver to securely tighten the needle 
clamp screw.
aNeedle stopper
b Hole for setting the needle
c Flat side of needle
ePress   to unlock all keys and 
buttons.
 CAUTION
 Be sure to push in the needle until it touches 
the stopper, and securely tighten the needle 
clamp screw with a screwdriver. If the needle 
is...
Start reading Brother Super Galaxie 2 Manual

Related Manuals for Brother Super Galaxie 2 Manual

All Brother manuals