Home > Brother > Sewing Machine > Brother Super Galaxie 2 Manual

Brother Super Galaxie 2 Manual

Here you can view all the pages of manual Brother Super Galaxie 2 Manual. The Brother manuals for Sewing Machine are available online for free. You can easily download all the documents as PDF.

Page 231

ADJUSTMENTS DURING THE EMBROIDERY PROCESS
Embroidery
229
5
ADJUSTMENTS DURING THE EMBROIDERY PROCESS
If the Bobbin Runs Out of Thread 
When the bobbin begins to run out of thread 
during embroidering, the machine will stop and 
the message below will appear. Press   and 
follow the directions below to rethread the lower 
threading. If very little sewing remains, you can 
embroider 10 final stitches without rethreading the 
machine by pressing  . The machine will stop 
after sewing the 10 stitches.
aPress...

Page 232

ADJUSTMENTS DURING THE EMBROIDERY PROCESS
230
If the Thread Breaks During 
Sewing 
aPress the “Start/Stop” button to stop the 
machine. 
bIf the upper thread is broken, redo the 
upper threading. If the bobbin thread is 
broken, press   and follow the 
directions in steps 
a through e from the 
previous section to reset the bobbin. 
cPress .
dPress the “Presser Foot Lifter” button to 
lower the presser foot.
ePress 
→ The camera view window appears.
fPress , , or  to move the 
needle back the correct...

Page 233

ADJUSTMENTS DURING THE EMBROIDERY PROCESS
Embroidery
231
5
Restarting from the Beginning 
aPress .
bPress .
→The embroidery frame moves, returning the needle 
to the pattern’s beginning position.
cPress the “Presser Foot Lifter” button to 
lower the presser foot and start sewing.
Resuming Embroidery After 
Turning Off the Power
The current color and stitch number are saved 
when embroidery is stopped. The next time the 
machine is turned on, you have the option to 
continue or delete the pattern....

Page 234

ADJUSTMENTS DURING THE EMBROIDERY PROCESS
232
cAttach the embroidery frame and press .
→The previous sewing screen displayed before the 
machine was turned off appears.
dContinue embroidering.
aStitch number when embroidery is resumed
Memo
 If you want to start a new embroidery pat-
tern, press   so the pattern selection 
screen appears.
a 

Page 235

MAKING EMBROIDERY ADJUSTMENTS
Embroidery
233
5
MAKING EMBROIDERY ADJUSTMENTS
Adjusting Thread Tension
When embroidering, the thread tension should be 
set so that the upper thread can slightly be seen on 
the wrong side of the fabric. 
■Correct Thread Tension
The pattern can be seen from the wrong side of the 
fabric. If the thread tension is not set correctly, the 
pattern will not finish well. The fabric may pucker or 
the thread may break. 
a Right side
b Wrong side
Follow the operations described...

Page 236

MAKING EMBROIDERY ADJUSTMENTS
234
■Upper Thread is Too Loose
The tension of the upper thread is too loose, 
resulting in a loose upper thread, loose thread locks, 
or loops appearing on the right side of the fabric.
a Right side
b Wrong side
aPress .
bPress   to tighten the upper thread 
tension. (The tension number will increase.)
cPress .
Adjusting the Alternate Bobbin 
Case (with No Color on the 
Screw)
When using the embroidery bobbin thread 
provided, please be sure to choose the green 
marked...

Page 237

MAKING EMBROIDERY ADJUSTMENTS
Embroidery
235
5
■Bobbin Thread is Too Loose
Bobbin thread appears slightly on the right side of 
fabric.
a Right side
b Wrong side
If this occurs, turn the slotted screw (-) clockwise, 
being careful not to over-tighten the screw, 
approximately 30-45 degrees to increase bobbin 
tension.
■Bobbin Thread is Too Tight
Upper thread on the right side of fabric seems to be 
lifting/looping and bobbin thread is not seen on the 
wrong side of fabric.
a Right side
b Wrong side
If...

Page 238

MAKING EMBROIDERY ADJUSTMENTS
236
Using the Thread Trimming 
Function (JUMP STITCH TRIM)
The thread trimming function   will 
automatically trim any excess thread jumps within 
the color. This function is initially turned on. To 
turn this function off, press   key and then . This function can be turned on or off during 
embroidering.
* Your customized setting remains after turning the  machine off and on.
a Jump stitch
aPress .
bPress   to turn off the thread trimming 
function.
→The key will display as...

Page 239

MAKING EMBROIDERY ADJUSTMENTS
Embroidery
237
5
Adjusting the Embroidery Speed
aPress  and .
bIn the “Max Embroidery Speed” display, use    to change the maximum 
embroidery speed. 
* You can choose from 3 different speed levels. 
cPress .
Changing the Thread Color 
Display
You can display the name of the thread colors or 
embroidery thread number.
aPress .
bPress .
cIn the “Thread Color Display”, use     
to display the name of the thread colors or 
the embroidery thread number.
Memo
 SPM is the number...

Page 240

MAKING EMBROIDERY ADJUSTMENTS
238
dWhen the thread number   is 
displayed, use     to select from six 
embroidery thread brands pictured below.
* Depending on the country or area, cotton-like polyester thread is sold.
ePress . 
Changing the Embroidery Frame 
Display 
aPress .
bPress .
cIn the “Embroidery Frame Display”, use   
 to change the embroidery frame display 
mode. 
* There are 14 choices.
EMBROIDERY / POLYESTER 
THREAD#
COUNTRY/COTTON THREAD#*
MADEIRA /POLYESTER 
THREAD#
MADEIRA RAYON THREAD#...
Start reading Brother Super Galaxie 2 Manual

Related Manuals for Brother Super Galaxie 2 Manual

All Brother manuals