Brother Hl 5130 User Manual

CONTROL PANEL   3 - 5
Service call indications
If there is an error that cannot be cleared by the user, the printer will show that a service call is needed 
by lighting up all the LEDs as shown in Figure 3-12.
Figure 3-12
If you see the service call indication above, follow the steps below:
1Take out the DIMM (Dual Inline Memory Module) from your printer, if you have a DIMM installed. 
2Turn off the power switch, wait a few seconds, and then turn it back on and try to print again. 
If you cannot clear...

3 - 6   CONTROL PANEL
Table 1: LED indications while pressing Go and Job Cancel
Make a note of the indication and report the error status to your dealer or a Brother authorized service 
representative by referring to the above table.
*1 If this error occurs, turn the power switch off, wait a few seconds, and then turn it on again.
Leave the printer for 10 minutes with the power on. If the error occurs again, consult your dealer or 
Brother authorized service representative.
LEDs Fixing unit...

CONTROL PANEL   3 - 7
Control panel buttons 
The control panel buttons have the following functions:
Cancel printing
If you press the Job Cancel button while printing, the printer will immediately stop printing and will then 
eject the paper.
Wake-up 
If the printer is in Sleep mode, press the Go or Job Cancel button to wake the printer up and go to the 
Ready state. 
Form feed
If the yellow Status LED is on, press the Go button. The printer will print any data that is left in the printer 
memory.
Error...

3 - 8   CONTROL PANEL
Print a test page
You can use the Go button or the printer driver to print a test page.
Using control panel button
1Turn off the printer.
2Make sure that the front cover is closed and the power cord is plugged in.
3Hold down the Go button as you turn on the power switch. All the LEDs light up and then go off 
again. Keep the Go button pressed down until the Toner LED comes on. When the Toner LED 
comes on, release the Go button.
4Press the Go button again. The printer will print a...

CONTROL PANEL   3 - 9
Printer Settings
You can print the current settings using the control panel button or printer driver.
Using the control panel button
1Make sure that the front cover is closed and the power cord is plugged in.
2Turn on the printer and wait until the printer is in the Ready state.
3Press the Go button three times. The printer will print the current printer settings.
Using the printer driver
If you are using Brother’s Windows® PCL printer driver, you can print the current printer...

3 - 10   CONTROL PANEL
Print fonts (Not available for HL-5130)
You can print a list of the internal fonts using the control panel button or printer driver.
Using the control panel button
1Turn off the printer.
2Make sure that the front cover is closed and the power cord is plugged in.
3Hold down the Go button as you turn on the power switch. All the LEDs light up and then go off 
again. Keep the Go button pressed down until the Toner LED comes on. When the Toner LED 
comes on, release the Go button....

CONTROL PANEL   3 - 11
Network factory default setting (For HL-5170DN)
If you wish to reset the print server back to its default factory settings (resetting all information such as 
the password and IP address information), please follow these steps:
1Turn off the printer.
2Make sure that the front cover is closed and the power cord is plugged in.
3Hold down the Go button as you turn on the power switch. All the LEDs will light up. Keep the button 
pressed down until the Toner LED comes on. When the...

4 - 1   OPTIONS
4
This printer has the following optional accessories. You can increase the capabilities of the printer with 
these items. Click the symbol L in the table to see the information for each item.
DIMM
We recommend that you expand the printer memory to avoid any memory full errors.
For HL-5140 and HL-5150D
This printer has 16 MB of standard memory and a slot for optional additional memory. The memory can 
be expanded up to a total of 144 MB by installing a commercially available DIMM (Dual...

OPTIONS   4 - 2
Installing additional memory
1Turn off the printer power switch, and then unplug the printer. Disconnect the interface cable from 
the printer.
Figure 4-1
Caution
Make sure you turn the printer OFF before you install or remove the DIMM.
2Remove the side cover. Use a coin to loosen the two screws, and then remove the metal plate.
3Unpack the DIMM and hold it by the edges.
Caution
DIMM boards can be damaged by even a small amount of static electricity. Do not touch the memory 
chips or the...

4 - 3   OPTIONS
4Hold the DIMM by the side edges. Line up the notches on the DIMM with the DIMM slot. (Check that 
the locks on each side of the DIMM slot are open or facing outwards.)
Figure 4-4
5Press the DIMM straight into the slot (press firmly). Make sure the locks on each side of the DIMM 
click into place. (To remove a DIMM, you must release the locks.)
6Put the metal plate back on and secure the metal plate with the two screws.
7Put the side cover back on.
8Reconnect the interface cable (printer...