Brother HL 2070NR User Manual

Driver and software
2 - 15
2
Brother Laser driver for Macintosh®
For Mac OS® 9.1 to 9.2
1Open the Extensions folder located in the System Folder on the Macintosh HD.
2Drag all these following files in the Extensions folder to the trash.
 BR_PrintMonitor(laser)
 Brother Laser
 Brother Laser(IP)
Note
There may be several of the USB Print Driver(BRXXX)* and BR_PrintMonitor(BXX)* extensions with different 
endings.
*The x refers to the model of your machine.
3Restart the Macintosh®.
4Once the computer has...

Driver and software
2 - 16
2
Software
Note
This section is for Windows®.
Software for Networks
Note
This section is for HL-2070N.
BRAdmin Professional
The BRAdmin Professional software is a utility for managing your Brother network enabled printers that are 
running under Windows® 95/98/Me, Windows NT® 4.0 and Windows® 2000/XP. 
It allows you to easily configure and check the status of your printer on the network.
Driver Deployment Wizard
This installer includes the Windows® printer driver and Brother...

Driver and software
2 - 17
2
Automatic Emulation Selection
Note
This section is for HL-2070N.
This printer has an Automatic Emulation Selection feature. When the printer receives data from the computer, 
it automatically chooses the emulation mode. This feature has been set at the factory to ON.
You can change the setting using Remote Printer Console or Web browser. 
Note
For more information about Remote Printer Console, see the following section.
The printer can choose from the following combinations:...

3
3 - 1
3Control panel
This section refers to the four Light Emitting Diodes (LEDs) (Toner, Drum, Paper, Ready) and a control panel 
button (Go) on the control panel.
The LED indications shown in the table below are used in the illustrations in this chapter.
Note
When the power switch is off or the printer is in Sleep mode, all the LEDs are off.
LED is off
 or   or 
LED is on
 or 
 or LED is blinking
 

Control panel
3 - 2
3
LED Printer status
Sleep mode
The power switch is off or the printer is in Sleep mode. Pressing the Go button 
wakes up the printer from Sleep mode to Ready mode.
Ready to print
The printer is ready to print.
Warming up
The printer is warming up.
Receiving data
The printer is either receiving data from the computer, processing data in 
memory or printing the data.
Data remaining in memory
Print data is left in the printer memory. If the Ready LED blinks for a long time 
and nothing...

Control panel
3 - 3
3
Toner life end
Replace the toner cartridge with a new one. See Replacing the toner cartridge 
on page 5-3.
Cartridge position error
The toner cartridge is not installed correctly. Take out the toner cartridge and put 
it back into the printer again.
Drum life end soon
The drum unit is near the end of its life. We recommend that you get a new drum 
unit to replace the current one. See Replacing the drum unit on page 5-8.
The Drum LED alternates turning on for 2 seconds and off for 3...

Control panel
3 - 4
3
Front cover is open
Close the front cover of the printer.
Back cover is open
Close the back cover of the printer.
Paper jam
Clear the paper jam. See Paper jams and how to clear them on page 6-5. 
If the printer does not start printing, press the Go button.
No paper fed manual feed slot
Put the paper in the manual feed slot. See Printing on plain paper, bond paper 
or transparencies from the manual feed slot on page 1-10 or Printing on thick 
paper, labels and envelopes from the...

Control panel
3 - 5
3
Service call indications
If there is an error that cannot be cleared by the user, the printer will show that a service call is needed by 
lighting up all the LEDs as shown below.
If you see the service call indication above, turn off the power switch, wait a few seconds, and then turn it 
back on and try to print again.
If you cannot clear the error and see the same service call indication after turning the printer back on, call 
your dealer or a Brother authorized service...

Control panel
3 - 6
3
Table 1: LED indications while pressing Go button
Make a note of the indication and report the error status to your dealer or a Brother authorized service 
representative by referring to the above table.
Note
Make sure that the front cover is fully closed before you report a service call.
*1 If this error occurs, turn the power switch off, wait a few seconds, and then turn it on again.
Leave the printer for 10 minutes with the power on. If the error occurs again, consult your dealer...

Control panel
3 - 7
3
Control panel button (Go button)
The control panel button has the following functions:
Wake-up
If the printer is in Sleep mode, press the Go button to wake the printer up and go to the Ready state. 
Error recovery
If there is an error, the printer will recover automatically from some errors. If an error is not automatically 
cleared, press the Go button to clear the error, and then continue to use the printer.
Form feed
If the green Ready LED blinks for a long time, press the Go...