Boxlight Seattle Series User Manual

							38
MENU
VOL -VOL+
MENU
INPUT
PIN Key In Operation
When the projector is turned on and the 
PIN LOCK PROTECTION is set to [ON], 
the image will show as on the right side.
1.   Press the MENU button on the projector 
or remote control. Enter PIN code by 
keypad or remote control.
2.  How to enter a PIN code? 
You can use control panel or remote 
control.
CONTROL PANEL 
KEYSTONE REMOTE CONTROL
The control panel and remote control buttons to enter a sequence 
of PIN code is like the photo below.
(1)	Press	◄	button:	Select	the	[	1	]
(2)	Press	▲	button:	Select	the	[	2	]
(3)	Press	►	button:	Select	the	[	3	]
(4)	Press	▼	button:	Select	the	[	Enter	]	move	to	next	row.(4~6,7~9,	
~OK)
(5)   Press 
 (backspace) item: 
In case you enter a wrong digit, select  to delete the wrong digit you entered.
(6)   Press 
 item: 
Once all four digits of the PIN are entered, select 	to	confirm.
NOTE
If the PIN is incorrect, a ‘ Enter new code ” message will be show\
n. Please try again. If the PIN 
code input is incorrect for three times, a warning message will show up \
and the  projector will shut 
itself down in 30 seconds.
If you have no idea about the PIN, please contact your dealer for help. 
						

							39
Network Control Software Application
	 
Register the projector(s) which needs to be controlled. 
" Auto search " can help you to seek the projector(s) source easily. 
After registering in the work group, you can start to control the projec\
tor.
		Group the projector(s) into different sections. 
You can monitor the status easily by the sort of group name function in t\
he network.
		Monitor the status for each projector. 
a.You can manage and change the monitoring content by System Parameter Sett\
ing. 
b.	
The 	Lamp 	timer, 	filter 	working 	time 	or 	system 	warning 	feedback 	etc. 	can 	be 	known 
by checking the status for projector(s).
		 Control the booked projector(s). 
The status can be refreshed and acquired by monitoring functions; you ca\
n also 
operate the function easily by Network Control.
NOTE
To  monitor  and  control  the  projector(including  stand-by  mode),  the  following 
conditions need to be ready:
(1) Projector should already be powered on.
(2) Projector is connected to network.
(3)   LED  light  of  the  projector  network  port  shows  normal.  (Green  light  on,  Orange 
twinkle)
*  
Stand-by	mode	indictor:	Green	LED	(Power)	on	the	projector’s	control	panel	flashes.
NOTE:   
This  Network  Control  Software Application  is  an  optional  function  and  support 
model with RJ45 LAN port only.
LAN 
						

							40
Before Use
Before To Use Network Control Software
		If the system is Windows 2000, NT 4.0 or XP, the PC should be started by the 
Administrator.
		
Before starting the Network Control software, please check the following\
.
(1) The computer must have Network Control software installed.
(2)    The projector should be powered on and the LAN wire is well connected to\
 
projector.
(3)The LAN module ON/OFF item in SECURITY menu of OSD should be setting ON.
(4)   Make sure the computer and projector can connect to network. Network Con\
trol 
software needs to arrange in TCP/IP network communication and the network cable.
Open Network Control Software
		 Click Network control software icon.
 
		 Monitor window will show as Graph 1.
 
						

							41
Before Use 
Projector Auto Search.
		Click the  (Projector search), located projector will show on the network 
correctly. 
(Graph2)
		 Click  (search again), the projector which is well connected with a PC will be 
shown. 
(Graph3)
NOTE
When the security warning window appears while Network Control is execut\
ing, 
please select "Unblock" to decontrol area network linking against from S\
ystem 
Administer.


NOTE
If there is no projector found on the display window, the following maybe the causes:
1.    There is no DHCP server available on the LAN. The LAN module is shipping 
with	DHCP-configured	client	enabled	in	default.
2.   If there is no DHCP server available on the LAN. The LAN module default IP 
address should be 169.254.1.1. Please modify the PC/Laptop IP address setting to 
make the PC/Laptop IP address located on the same segment as 169.254.xxx.xxx 
and try again. 
						

							42
Before Use
		Projector Auto Search can rank group names or display names by clicking the 
monitor window title (Group Name) or (Projector Name). This will help you easily 
to understand projectors status.

 Monitor window
		Click  (register projector), the projector information will show on the monitor 
window. Click 
 button (exit), it will cancel the registered item then return to 
register table.
Projector Auto Search. 
						

							43
Before Use 
		After registering, you can click  button (Data single capture) in the tool bar or 
click 
 button (Start Auto Scan) running in this program to monitor the projector.
NOTE
When pressing  "About " button for help, you will see icons explained as in the chart.\
 
Projector Auto Search. 
						

							44
Before Use
Modify The Projector Setting
		If modifying the registered projector setting is needed, please move you\
r cursor to 
the data table and click the item that you would like to modify, the detail will be 
shown on the right side table.
< Graph 5 > : Register Table
		After setting, you can save the data by clicking  button or cancel by clicking  
button.
Item Description
Display nameShow the Host name
(16 characters at most in ASCII)
IP Address Show the IP Address
Mask Show the Mask
Gateway Show the Gateway
MAC Show up the MAC code
(The	default	value	can	not	be	modified)
DHCP Capture IP address from network sensor
automatically.
< Table 1 > : Setting Windows 
						

							45
Registering And Configuring The Projector
Delete
		Select the registered projector in monitor window. Click mouse right key and select 
" Delete " to erase the registered projector data.
< Graph 6 > : Register Table. 
						

							46
Registering And Configuring The Projector
Projector Setting
		Select the registered projector in monitor window. Click mouse right key and select 
"projector	setting"	to	modify	the	registered	projector	data.	
After	finishing	the	setting,	
you can save by clicking 
 button or cancel by clicking  button.
< Graph 7 > : Register table.
< Graph 8 > :Setting table. 
						

							47
Registering And Configuring The Projector
Projector Setting
	Click  button (system setting) to modify system alert setting.
< Graph 9 >