Boxlight Raven Users Manual

xUser’s Manual
Display
Option Actions/Descriptions
Phase  Synchronizes the signal timing of the display with that of the graphic 
card. If you experience an unstable or flickering image, use the phase 
function to correct it.
Select the desired setting with the s tbuttons:
xPress the s button to decrease the value.
xPress the t button to increase the value.
Tracking  Changes the display data frequency to match the frequency of your 
computer graphic card. If you experience a vertical flickering bar, use...

xUser’s Manual
Language
Option Actions/Descriptions
Language  Selects the language for menu and message displayed.
Select the language you prefer with the 
uvbuttons, and confirm the selection 
with the MENU\ENTER button on the Projector Control Panel or the Enter 
button on the Remote Control.
xEnglish
xDeutsch
x
x
xFrançais
xEspañol
xPortuguês
xItaliano
x
x 

xUser’s Manual
Advanced
Option Actions/Descriptions
Auto Source  Automatically scans the input source.
Select
xPress the MENU\ENTERbutton on the Projector Control Panel or the 
ENTER button on the Remote Control to active this function. 
Rear  The image is reversed horizontally.
xPress the MENU\ENTERbutton on the Projector Control Panel or the
ENTERbutton on the Remote Control to active this function.
Ceiling  The image is inverted vertically.
xPress the MENU\ENTERbutton on the Projector Control Panel or...

xUser’s Manual
Color Space  Manually selects signal type.
Select the input signal type with the s tbuttons:
xRGB
xYCbCr
xYPbPr
Auto Shutdown  Uses this function to automatically turn off the lamp if the projector does not 
detect an input signal for specified time period (30 minutes).
Select the desired setting with the s tbuttons:
xON
xOFF
OSD Timeout  Duration OSD (On-Screen Display) menu stays active (at idle state by second).
Select the desired setting with the s tbuttons.
Menu Position  Selects the...

xUser’s Manual
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt or spots will 
project on the screen and diminish image quality. The only part you could replace yourself is the lamp. If
any other parts need replacing, contact your dealer or qualified service personnel. When cleaning any
part of the projector, always switch off and unplug the projector first. 
Warning:
Never open any of the covers on the projector except the lamp cover. Dangerous electrical...

xUser’s Manual
Replacing the Lamp
Projector lamps have a finite life. Replace the lamp when:
xThe image becomes darker and hues become weaker after a lamp has been for a long period of time.
xThe projector lamp LED indicator turns into red. Refer to section titled “Indicator Messages” for 
further details.
wThe lamp becomes high temperature after turning off the projector with the power button. If you touch the 
lamp, you may scald your finger. When you replace the lamp, wait for at least 45 minutes for...

xUser’s Manual
1. Turn off the projector and unplug the AC 
power cord.
2. Place a protective sheet (cloth) beneath 
the projector. Turn the projector over so 
you can access the lamp cover.
3. Remove the access panel screws and 
open the panel.
4. Remove the screws on the bottom of the 
lamp assembly.
5. Grasp the lamp handle and pull the lamp 
assembly directly out of the projector.
6. Replace with the new lamp.
7. Place back the screws on the bottom of 
lamp assembly.
8. Place the panel and screw back...

xUser’s Manual
Technical Specifications
Specifications
Projection System: Single panel 0.55" DLP projector
Native resolution: 480,000 dot x1 (800 x 600 x1)
Image Brightness:1500 ANSI Lumens
Uniformity: 85%
Lens: Manual Zoom (1.2X)
Focal Length: 0.80" - 0.95" / 20.2 - 24.2mm
Contrast Ratio 2000: 1 (Full on/off)
Aspect Ratio:1:1, 16:9, 4:3
Screen Size: 30 - 200 inches
Lamp:200W
Projection Type:Front, Rear, Ceiling
Video Input:PAL,NTSC, SECAM
Input Source:Computer, HDTV, S-Video, Video...

xUser’s Manual
Appendix
Indicator Messages
LED Type  Color  Status  Meaning
Power LED:  Green  Flashing The projector is powered and ready.
Power LED: Amber SolidThe projector system has some problems with its 
fan, so the projector cannot start up.
Power LED: Green SolidThe projector is in good condition on working.
Lamp LED: Green SolidThe lamp is in good condition and is projecting at 
maximum brightness.
Lamp LED: Amber SolidThe lamp has reached its end of life and must be
changed soon. The lamp will...

xUser’s Manual
Preset Signals
Preset signal  fH (kHz)  fV (Hz)  Sync  Size
640 x 480 VGA mode 3  31.469  59.940  H(-), V(-)  800
VGA VESA 72Hz  37.861  72.809  H(-), V(-)  832
VGA VESA 75Hz  37.500  75.000  H(-), V(-) 840
VGA VESA 85Hz  43.269  85.008  H(-), V(-)  832
800 x 600  SVGA VESA 56Hz  35.156  56.250  H(+), V(+)  1024
SVGA VESA 60Hz  37.879  60.317  H(+), V(+)  1056
SVGA VESA 72Hz  48.077  72.188  H(+), V(+)  1040
SVGA VESA 75Hz  46.875  75.000  H(+), V(+)  1056
SVGA VESA 85Hz  53.674  85.061...