Boxlight Projector P7 WX32N User Manual

							20
Note:
● When the logo select is set to be "Off", the
   logo will not be displayed on the screen. 
1.Complete peripheral connections (with a 
   computer, VCR,etc.) before turning on the 
   projector.
2. Connect the projector’s AC power cord into 
    AC outlet.The POWER indicator turns red. 
3. Press the POWER button on top control or  
    on the remote control. The POWER indicator 
    becomes green and the cooling fans start to 
    work. The preparation display appears on 
    the screen.
4. If the projector is locked with a PIN code, a 
    PIN code input dialog box appears. Enter 
    the PIN code as instructed below.
Caution on handling the PIN code
If you forget your PIN code, the
projector can not longer be started.
Take a special care in setting a 
new PIN code. Write down the 
number in a column on page 65 of 
this manualand keep it properly. 
Should the PIN code be missing 
or forgotten, consult your dealer or 
service center.
What is PIN code?
PIN (Personal Identification Number) code is a 
security code that allows the person who knows 
it to operate the projector. Setting the PIN code 
can prevent unauthorized use of the projector.
A PIN code consists of a three-digit number. 
Refer to the PIN code lock function in the 
"Expand" "Security" menu on pages 44 for PIN 
code lock operation of the projector. Move the cursor to OK, and press OK.
-----                   Input PIN code        Exit
 PIN Code
Set Cancel
Move                    Select                Reset
PIN Code
Set Cancel
*
Basic operation
Turn on the projector
Enter a PIN code
Press OK button to input PIN code. Press
 
button to select a number and press OK button 
to enter it to the PIN code box, then number 
changes to "*" and automatically move the 
cursor to next box. If you fixed an incorrect 
number, press MENU button to reset it again.
Repeat the step to complete entering a three-
digit number.
After entering the three-digit number, will 
automatically move the cursor to “Set”, press 
OK button so that you can start to operate the 
projector.
If you entered an incorrect PIN code, the “PIN 
code” and the number (***) turn red. PIN dode 
will be reset within one second automatically, 
Enter the correct PIN code all over again.  
						

							21
Basic operation
Turn off the projector
Power off ?
“Power off ? ” disappears after 4 seconds.
1. Press the POWER button on top control 
    or on the remote control, and “Power off?”  
    appears on the screen.
2. Then, press the POWER button again in 4 
     seconds. The POWER indicator starts to 
    flash red, and the cooling fans keep running  
    (You can select the level of fans’ quietness 
    and running speed.). Now you can unplug 
    the AC power cord even if the fans are still 
    running.
3  When the projector has cooled down enough 
    to be turned on again, the POWER indicator  
    stops flashing. 

Note:
● When the On start function is “On” , this 
   projector is turned on automatically by 
  connecting the AC power cord to an AC outlet .
● The running speed of cooling fans is changed       
   according to the temperature inside the 
   projector.
● Do not put the projector in a case before it is 
   cooled enough.
● If the POWER indicator flashes or emits a 
   red light, see “Power Indicator”.
● While the POWER indicator is flashing, the  
   lamp is being cooled down and the projector 
   cannot be turned on. Wait until the POWER 
   indicator turns red to turn on the projector 
   again.
● The fan rotation will terminate directly if the 
   AC power cord is unplugged immediately after 
   the projector is turned off.
● The projector can be turned on after the 
   POWER indicator turns red. The waiting 
   time to restart will be shortened when the 
   normal power-off processing for fan cooling 
   is completed, comparing with the time the AC 
   power cord is immediately unplugged after the 
   power-off. To maintain the lamp life, once you turn 
the projector on, wait at least 5 minutes 
before turning it off.
Do not operate the projector 
continuously without rest.
Continuous use may result in shortening 
the lamp life.Turn off the projector and 
let it stand for about an hour in every 24 
hours.  
						

							22
Remote control
Screen menu Top control
MEMU
MENU
OK/INPUT 
OK 
  

 
1 Press the MENU button on the top control or 
   the remote control to display the screen menu.
2 Press 
 buttons to select an entry in the main 
   menu and then press OK  button to enter the 
   submenu.
3 Press
 buttons to select your required item, 
   and then press OK button to set or enter  
    required item.
4 Press 
 buttons to adjust settings or switch 
   among the items. Press the OK button for  
   corresponding operation and then press MENU 
   button return to the submenu.
5 Press MENU button to return to the previous 
   menu. Press MENU button  again to exit the  
   screen menu.
PC adjust
Display
Color adjust
Setting
Expand
Info.
Move Next Exit
Auto PC adj.             
Fine sync                             16
Total dots                          1056
Horizontal                           216
Vertical                              27
Display area H                       800
Display area V                       600
Reset 
Mode free
Store
Basic operation
How to operate the screen menu
The projector can be adjusted or set via the 
on-screen menu,Each main menu can be 
divided into several levels of submenus, and 
submenus are also divided into several levels 
of sub-submenus.
For each adjustment and setting procedure, 
refer to the respective sections in this manual.  
						

							23
Menu bar
① PC adjust
   Adjust computer parameters to match with VGA input signal format: auto PC adj, Fine sync,      
     Total dots, Horizontal, Vertical, Display area H, Display area V.
②  Display
     - Screen Size: select the projecting image screen size.
        If a computer is selected as a signal source, the following setup options for the image size are 
        available: Normal, Wide, Custom.
        If video equipment is selected as a signal source, the following\
 setup options for the image 
        size are available: Normal,Wide or Custom.
      - Keystone: select keystone function to correct image keystone distortio\
n.
      - Project Mode: select a project mode among  Front, Rear, Celing/Front and Ceiling/Rear.
      - Menu Position: set the menu's position on the screen. 
      - Background Display: set the background display color for project scree\
n.
      - System: select a system signal format to match the input source.
③  Color adjust
      -
  Image mode:the available image modes is 
Normal, Natural, Cinema, Blackboard (green),  
         Colorboard
 or User Image.
      - 
 Image color adjust:
       
  If a computer is selected as a signal source, the following image adjust\
ing options are 
        available: Contrast, Brightness, Color temp., White balance (R/G/B)  and Sharpness.   
        If video equipment is selected as a signal source, the following\
 image adjusting options are 
        available: Contrast, Brightness, Color, Tint, White balance (R/G/B), Sharpness  and 
         Progressive .
④  Setting
        Configure basic operation settings of the projector: 
On start, Standby mode, High land,  
       Lamp control, Cooling fast, Closed caption, Key lock, Iris, Terminal and Sound.
 
⑤  Expand
        Configure expand operation settings of the projector: 
Language, Auto setup, Logo, Security, 
       Power management, Filter counter, Pattern, Network and Factory default. 
⑥  Info.
       Display the system information of the projector.
 
Main menu
Sub menu
PC adjust
Display
Color adjust
Setting
Expand
Info.
Move Next Exit
Auto PC adj.             
Fine sync                             16
Total dots                          1056
Horizontal                           216
Vertical                              27
Display area H                       800
Display area V                       600
Reset 
Mode free
Store①
②
③
④
⑤
⑥
Basic operation  
						

							24
Auto setup functionAdjust zoom and foucus
This function is available just by pressing the  
AUTO button on the remote control. The system 
then automatically performs various settings in the 
setup menu, including input source search and 
auto pc adjust.
Rotate the zoom ring to zoom in or zoom out 
the image.
Rotate the focus ring to adjust the focus of the 
image.
Zoom ring
(back)
Remote control AUTO Focus ring
(front)
Basic operation  
						

							25
VolumeRemote controlMUTE
VOLUME +/- 
Menu operation
Volume menu
Volume
Press  to increase the volume and  to 
decrease  the volume.
Mute
Press
 button to switch the mute function On/
Off. 1 Press the MENU button to display the screen 
   menu.  Press 
 button to select the Setting 
   menu icon. Press OK to enter the submenu 
   entry.
2 Press 
 button to select Volume and then 
    press OK button.
3 Press 
 button to select Volume or Mute to  
   adjust.
PC adjust
Display
Color adjust
Setting
Expand
Info.
Move Next Exit
On Start                    Off
Standby Mode                Normal
High Land                   Off
Lamp Control
Cooling Fast                Normal
Closed caption              Off
Key Lock   
Iris                        Off
Terminal                    VGA OUT
Sound                       
    Volume   12
    Mute     Off
Basic operation
Direct operation
VOLUME
Press the VOLUME +/- button on the remote 
control to adjust the volume.
MUTE
Press the MUTE button on the remote control 
and select On to turn off the audio temporarily. To 
restore the audio to its previous level, press the 
MUTE button again and select  Off or press the 
VOLUME+/– buttons. 
Mute function is also effective for AUDIO OUT 
jack.  
						

							26
Remote control operation
INPUT 
Press INPUT button on the remote control to 
select the input source.
FREEZE 
Press FREEZE button to freeze the picture on the 
screen. To cancel the freeze function, press the 
FREEZE button again or press any other button.MUTE
Press MUTE button on the remote control to turn 
off the volume. Press MUTE button again or any 
other buttons to cancel mute function.
VOLUME +/-  
Press image VOLUME +/- button on the remote 
control to increase or decrease the volume.
INPUT 
Remote control
FREEZE
VOLUME +/-  MUTE 
Basic operation
Using the remote control for some frequently used operations is advisable. Just pressing one of the 
buttons enables you to make the desired operation quickly without callin\
g up the screen menu.

Note:
   See the next page for the description of other    
   buttons.  
						

							27
D.ZOOM+ 
Press D.ZOOM+ button, the on-screen menu 
will disappear, while the information on digital 
zoom + appears. You can press Select to zoom 
in the image size, and press   ▲▼◄►to move 
the image horizontally and vertically.
The moving is effective only when the image is 
larger than the size of the screen.
D.ZOOM-  
Press D.ZOOM- button, the on-screen menu 
will disappear, while the information on digital 
zoom - appears. Press OK button to zoom in 
the image size.
To exit the “digital zoom +/-“mode, press any 
button except the D.ZOOM+/- and the OK 
button. 
To return to normal size, select “ Screen size” 
in  "Display" menu to adjust screen size, or 
Press    button to move the image 
horizontally or vertically.   BLANK 
BLANK 
Press BLANK button to black out the image. 
To restore to normal, press the BLANK button 
again or press any other button. 
The screen changes each time you press the 
button as follows:
Black out →Normal →Black out →Normal ...
“Blank” disappears after 4 seconds if there is 
no other button operation.
TIMER Blank ImageBlank
02：02
D.ZOOM +/- 
Basic operation
TIMER 
Press TIMER button. The timer display “00:00” 
appears on the screen and the timer starts to 
count time (00:00–59:59).
To stop the Timer, press TIMER button again, and 
then the Timer display disappears.
Timer display
Remote control  
						

							28
Input select
Direct Operation
Press HDMI, VGA, COMOPNENT, S-VIDEO 
or VIDEO button to select HDMI, VGA IN, 
Component, S-video or Video as input source.When input source is from 
computer connected to VGA 
IN 1 terminal with VGA cable,  
please select VGA IN 1.When input source is from 
computer connected to VGA IN 
2/VGA OUT terminal with VGA 
cable,  please select VGA IN  2.
 Note:
  -  When the Input Search function is set to On in the Auto setup function, the input signal will be 
    searched automatically.
  - When VGA IN 2/VGA OUT terminal is used as VGA OUT, VGA IN 2 can not be selected.  Menu operation
1 Press MENU button on the remote control or 
   top control to display the input select menu. 
2 Press 
 button to select HDMI,VGA IN, 
   Component, S-video or Video , then press 
   OK button. Top control
Input select menu
Remote control
INPUT 
VGA IN 2
INPUT VIDEO
HDMI
COMPONENT VGA 
S-VIDEO
    HDMI    
    VGA IN 1
    VGA IN 2
    Component
    S-video
    Video  
When input source is from  
equipment connected to HDMI  
terminal with HDMI cable,  
please select  HDMI.
(
Some model 
doesn't support this function.)
HDMI
ComponentSelect it when the input source 
is from the video equipment 
connected to COMPONENT 
terminal with a RCA cable.
Select it when the video input 
signal is connected to S-VIDEO 
terminal. Select it when the video input 
signal is connected to VIDEO 
IN terminal.
VGA IN 1
   S-video  Video  
						

							29
PC Adjust
Auto PC adj.
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and 
Vertical to conform to your computer.
Store Menu operation
The system parameters adjusted in the Auto PC 
adj. can be stored in the projector.
√ Note:
  - Total dots and horizontal & vertical positions of some computers cannot b\
e fully adjusted with this 
     Auto PC adj. function. When the image is not provided properly with this function, manual adjustments 
    are required.
  - The Auto PC adj. cannot be operated when 480i, 576i, 480p, 576p, 720p, 1035i, or 1080i is selected in 
    the System menu of computer inputx.
Auto PC adj.PC adjust Menu
1 Press MENU button on  the remote control to  
   display screen menu. Press  
  button to 
   select PC adjust,then press OK button.
2 Press   button to select Auto PC 
   adj.,then  press OK button.PC adjust
Display
Color adjust
Setting
Expand
Info.
Move Next Exit
Auto PC adj.             
Fine sync                             16
Total dots                          1056
Horizontal                           216
Vertical                              27
Display area H                       800
Display area V                       600
Reset 
Mode free
Store