Boxlight Projector P7 WX32N User Manual

10
Part names and functionsTerminals
① ②
③④
⑤ ⑥⑦
⑧
⑨⑩
①   AUDIO OUT 
*
      - Connect external audio amplifier to this 
       jack.
      - Output audio signal from  
②，⑦ or
⑧ .
②   AUDIO IN (R/L) 
*
      - Connect the video equipment connected 
       to  ③  or 
④  to this jack.
      -
 For a mono audio signal (a single audio
       jack), connect it to L(MONO) jack.
③   COMPONENT/VIDEO IN
     - Connect video signal to VIDEO port.
     - Connect composite video or component 
      video signal to...

11
Part names and functions
Top Control and Indicators
①  POWER indicator
     - Lights red when the projector is in stand-   
       by mode.
     - Lights green during operations.
      - Flashes green in the Power management  
       mode.
       - Flashes red during fans cooling.
     - Lights orange when abnormal is detected 
       in the projector.
     - Flashes orange when internal temperature 
       is abnormally high. 
②
  WARNING indicator
     Lights red when the life of the projection...

12
Remote control① POWER 
   Turn on or turn off the projector.(Page 21)
② VGA
  Select VGA as input source.(Page 28)
③ INPUT 
  Enter input source menu to select input 
    source directly. (Page 28)
④ HDMI
 *  
  Select HDMI as input source.(Page 28)
⑤ MENU
  Open or close the screen menu.(Page 22)
⑥ COMPONENT 
    Select component as input source.(Page 28)
⑦ BLANK 
  Temporarily close the image on the screen.
   (Page 27)
⑧ VIDEO 
  Select Video as input source.(Page 28)
⑨ S-VIDEO 
  Select S-video as...

13
⑱⑲
⑳
⑭
⑯ ⑫
⑬
⑮
⑰
⑫  DZOOM+
    Select the digital zoom + mode.(Page 27)
⑬ TIMER 
    Enable the timer function.(Page 27)
⑭  VOUME +  
   Increase the volume level.(Page 2 5)
⑮ AUTO 
    Enter auto setup mode.(Page 2 4)
⑯  VOUME -  
   Decrease the volume level.(Page 25)
⑰  FREEZE 
    Freeze the projected image.(Page 26)
⑱ DZOOM- 
    Select the digital zoom - mode.(Page 27)
⑲
 MUTE
     Mute the sound.(Page 25)
⑳  BACK 
  Return to main menu.(Page 22)
Part names and functions  

14
 Install remote control batteriesOperating range
①  Open the battery
      compartment lid. ② Install new batteries
     into the compartment.③ Replace the 
      compartment lid.
Two AAA  batteries
For correct polarity 
(+ and –), be sure 
battery terminals 
are in contact 
with pins in the 
compartment.
Point the remote control toward the projector 
remote receiver when pressing any button. 
The maximum operating range for the remote 
control is about 5 meters and 60 degrees 
vertically and...

15
4:3
16:9
16:10
Installation
Positioning the projector
 Note:
● The brightness in a room has a great influence on picture quality . It is recommended to limit the 
     ambient lighting in order to get the best image.
● All measurements are approximate and may vary from the actual sizes.
Screen size
(WxH)mm
4:3 aspect 
ratio 30"
100" 150" 200" 300"
610x457 2032x1524
3048x2286 4064x30486096x4572
Maximum 0.88m3.00m4.49m 6.00m 9.02m
Minimum 1.06m3.60m5.40m 7.21m10.83m
Screen size...

16
InstallationConnecting to computer(Digital and analog RGB)
Cables used for connection:
● VGA cable                                                              ● Serial control cable
● HDMI cable                             
Unplug the power cords of both the projector and external equipment from the  AC outlet 
before connecting the cables.
HDMI output*
HDMIcable*
HDMI*RS-232C port Serial output
Serial 
control 
cable Monitor output
Monitor input
VGA
cable VGA
cable
VGA input VGA output
This terminal...

17
Installation
Connecting to video equipment (Video, S-Video)
Cables used for connection:(Cables are not supplied with the projector)\
● Video cable                                                  ● S-Video cable
●  RCA cable                                                   ● Audio cable
 
         S-VIDEO IN Video 
output
Component
 output Audio
 output
*Audio
 output*Audio
 output*
VIDEO IN
S-VIDEO
cable
RCA
cable
Audio
cable
*Audio
cable*Audio
cable*Video
cable
COMPONENT AUDIO IN
L/R
*AUDIO...

18
(R)* (L)*
(R)* (L)*
Audio 
cable*Audio cable*(stereo)Audio cable*(stereo) Note: The left and right 
channels  are combined when 
there  is  only  the  L(mono)  is           
inserted.
External audio equipment
Unplug the power cords of both the projector and external equipment from the 
AC outlet 
before connecting the cables.
Installation
Connecting to audio equipment
Cables used for connection:
● Audio cable(Cables are not supplied with the projector)                             
Audio input*
Audio...

19
Installation
Connect the AC power cord to the projector.
Connecting the AC power cord
This projector uses nominal input voltages of 
100–240V AC and it automatically applies to 
different input voltages. It is designed to work 
with a single-phase power system having a 
grounded neutral conductor. To reduce the risk 
of electrical shock, do not plug into any other 
type of power system. If you are not sure of 
the type of power being supplied, consult your 
authorized dealer or service station....