Bose Te 1 Sr User Guide

English – 11
SYSTEM SETUP
Step 2: Connect source audio to the AUX input
What you need for this step:
Note: If you currently have audio/video sources  such as a cable/satellite set-top box and 
a DVD player connected to your TV,  do not disconnect them. The audio output from the 
source should be connected to the TV and to  the CineMate 1 SR speaker array. Refer to 
“Product overview” on page 6.
A.Plug one end of the digital audio cable in to the corresponding AUX connector on the 
speaker array.
Note:...

12 – English
SYSTEM SETUP
Step 3: Connect a power cord to the speaker array
What you need for this step:
Plug the small end of the power cord into the connector labeled  Power.
Note: Do not plug the power cord into an AC  power outlet at this time. You will be instructed to do this later in the setup process.
Power cord
Power cord
Hershey_Setup.book  Page 12  Thursday, March 31, 2011  11:44 AM 

English – 13
SYSTEM SETUP
Step 4: Route the cables
A.Arrange the cables as needed for your setup location.
B. OPTIONAL: Secure cables under the clips in the channel running along the length of 
the speaker array.
Channel Cable clip
Hershey_Setup.book  Page 13  Thursday, March 31, 2011  11:44 AM 

14 – English
SYSTEM SETUP
Step 5: Position the speaker array
What you need for this step:
CAUTION: The speaker array must be placed on a solid flat surface. For proper support, all of the feet on the bottom of the speaker  array must be resting on the table top.
A. Turn the speaker array over and place it in front of your TV with the speaker grille 
facing into the room.
CAUTION: When positioning the speaker array, make  sure it is not blocking any ventilation 
openings on your TV. Refer to the owner’s...

English – 15
SYSTEM SETUP
Step 6: Set up the Acoustimass® module
What you need for this step:
CAUTION: Choose a stable and level surface for the Acoustimass module. Vibration can 
cause the speaker to move, particularly on smooth surfaces like marble, glass, or highly 
polished wood.
A. When placing the Acoustimass
® module on bare floors, or other smooth surfaces, 
attach the included rubber feet to the bott om of the module for greater stability and 
to protect your floor.
B. Plug the small end of the...

16 – English
SYSTEM SETUP
D.Place the Acoustimass module according to the following guidelines:
 For best sound quality, stand the Acoust imass module on its feet along the same 
wall as your TV, or along any other  wall in the front third of the room.
 The front opening of the module can face any direction.
 Make sure there is an AC outlet nearby.
CAUTION: Do not operate the Acoustimass module on  its front end, back end, side, or top.
Note: Be sure to remove all protective films from the Acoustimass...

English – 17
SYSTEM SETUP
First time startup
Step 1: Install the remote batteries
What you need for this step:
A. Slide the battery cover off the back of the remote control.
B. Install the two provided AA (IEC LR6) batte ries, matching the plus and minus ends 
of the batteries to the polarity mark ings inside the battery compartment.
C. Slide the battery cover on until it snaps into place.
Step 2: Run the ADAPTiQ® calibration.
What you need for this step:
The ADAPTiQ
® audio calibration system customizes...

18 – English
SYSTEM SETUP
A.Point the remote at the speaker a rray and press the system power button.
B. Check that the power indicator on the speaker array is on (white), indicating the 
system is on, and that the status indicator is off.
C. Put the ADAPTiQ
® headset on your head making sure 
the left and right sensors rest above your ears.
During the audio calibration the headset allows the 
CineMate
® 1 SR system to hear exactly what you 
hear.
D. Slide the ADAPTiQ connector cover off the end of the...

English – 19
SYSTEM SETUP
F.Follow the audible instructions given to you by the system.
Note:  After hearing the language prompt in English, you can press the ADAPTiQ button to select another language. Then press the volume up button to continue.
Note: After you select your language and press the volume up button to continue, you can go back to the beginning of the process at  any time by pressing the ADAPTiQ button.
G. When the process is done, unplug the ADAPTiQ headset from the speaker array and...

2 – Español
INFORMACIÓN DE SEGURIDAD
Lea esta guía del usuario
Dedique el tiempo que sea necesario para seguir atentamente las instrucciones de esta guía 
de instalación y de la guía del usuario, que le ayudarán a configurar y ut ilizar correctamente el 
sistema y a disfrutar de todas sus funciones avanzadas. Guarde estas guías para consultarlas 
en el futuro.
Todos los productos Bose deben utilizarse de acuerdo con las normas locales, estatales, 
federales e industriales.
El símbolo de relámpago con una...