Bosch WVD 24460 User Manual

							51Water not visible in the drum. Not a fault. 
The water lies below the visible part of the drum.
Washing solution is not completely 
drained.Pumped blocked by foreign objects.  Clean the pump (refer to page 44). 
Fluff-producing laundry was 
washed. The water drainage pipe or 
drain hose is blocked.Clean drainage pipe and/or 
drainage hose.
Water runs out from under the 
appliance.Screw fitting of the inlet hose is 
leaking.Tighten the screw-fitting.
Drainage hose is leaking. Replace the drain hose.
Foam comes out of the detergent 
drawer. The *symbol is displayed 
at the end of the programme.Too much detergent or detergent 
not suitable for use in washing 
machines used.Mix 1 tablespoon of fabric softener 
with
½ litre of water and pour into 
chamber II of the detergent 
dispen­ser. 
Reduce detergent dosage for next 
wash cycle or use detergent which 
is suitable for use in washing 
machines.
The washing has not been spun 
correctly.Large laundry items have become 
entangled and are not evenly 
distributed in the drum.
For safety reasons, the high-speed 
final spin cycle was automatically 
cancelled.Do not put only large items in the 
drum.
Spin cycle actuated several times. Not a fault. 
Unbalanced load detection system is attempting to compensate the 
imbalance by spinning the washing several times.
Washing result not satisfactory. Soiling is greater than expected or 
recommended load has been 
exceeded.Select suitable programme and 
touch the Wash Plus È
 button 
or reduce load.
Detergent was underdosed. Dose detergent according to the 
manufacturers instructions.
Detergent residue on the washing. Some phosphate-free detergents 
contain water-insoluble residue 
which may appear as light stains on 
the washing.Select Rinse  immediately or 
brush out the washing after drying.
Grey residue on the washing. Soiling caused by ointment, grease 
or oil.Select maximum detergent dosage 
and maximum permitted 
temperatu­re for the next wash 
cycle. Problems Cause Remedial action
 
						

							52Programme duration changed 
during the programme sequenceNot a fault. 
See also explanations in the chapter Display field, programme 
duration from page 10.
Programme duration reduced Not a fault.
For small amounts of laundry, a reduc tion in time of approx. 30 minutes 
can result, depending on washing/drying programme.
Programme duration extended An overdosage of detergent has 
caused excessive formation of 
froth.An additional rinse cycle and 
spin cycle was run to ensure a good 
rinsing result.
The *
 symbol is displayed when 
the overdosage of detergent is 
detected.Reduce the detergent dosage for 
the next wash cycle.
For severe imbalances during   items 
spinning, an increase in time of  
approx. 10 minutes can occur . 
because of repeated distribution of 
the laundry. Wash large and small together in 
order to reduce the imbalance
If very cold water must be heated up, an increase in time up to 20 minutes 
can result. 
Drying programme does  Drying programme not selected.  Select the desired drying not start 
programme. 
Drying time/mode not set, or, set 
drying time is too short.. Set the reasonable drying time/
mode
Tap not turned on.  Turn on the tap. 
Loading door not closed properly.  Check whether laundry is trapped in 
door. Close the loading door (a click 
should be heard). 
Pump is blocked.  Clean the pump, 44. 
If the fault recurs, call Customer Service, see page 52.  Problems Cause Remedial action
 
						

							53
Consumption values 
Normal programme Additional 
optionLoad Consumption values** Programme 
duration
Power Water
Cottons 40 °C_ 5 kg 0.46 kWh  51.6 l 1:08 h 
Cottons 60 °C_ 5 kg 1.02 kWh  51.5 l 1:25 h 
Cottons Eco 60 °C Wash Plus
È* 5 kg 0.90 kWh 44.9 l 2:10 h 
Cottons 90 °C
(the hot washing solution is mixed 
with approx.7 litres of cold water 
before being drained)_ 5 kg 1.72 kWh  58.6 l 1:50 h 
Delicate/Silk 30 °C_ 2 kg 0.32 kWh  39 l 0:37 h 
Wool Ï  30 °C_ 2 kg 0.17 kWh  33.1 l 0:41 h 
Easy-Care = 40 °C_ 2,5 kg 0.34 kWh  33.8 l 0:50 h 
Dark Wash h
 30 °C_ 2,5 kg 0.32 kWh  52.1 l 1:06 h 
Sensitive s
  40 °C_ 5 kg 0.81 kWh  73.5 l 1:23 h 
Sport Wash ]
 30 °C_ 2,5 kg 0.21 kWh  38.6 l 0:41 h 
Super  Quick …
  30 °C_ 2 kg 0.21 kWh  34.8 l 0:15 h 
Mixed Load 40 °C_ 2,5 kg 0.60 kWh  36.2 l 0:50 h 
Intensive Dry Š_ 2,5 kg 1.83 kWh  30.6 l 1:51 h 
Gentle Dry ‰_ 1,5 kg 1.16 kWh  29 l 1: 27 h 
Cottons Eco 60 °C + Intensive Dry 
Š
  (2 auto drying cycles)Wash Plus
È* 5 kg 4.56 kWh 106 l 5:52 h 
(2:10 h 
+3:42 h)
* Programme setting with Wash PlusÈ* option for test in accordance or in conformity with EN 50 229 and 
IEC 50 229. 
**  Consumption values will  differ from the indicated values depending on the water pressure, water hardness, 
water inlet temperature, ambient temperature, type and quantity of laundry and degree of soiling, utilised 
detergent, fluctuations in the mains voltage and selected additional options. 
 
						

							54
Customer service 
Before you call customer service, please check 
whether you can eliminate the fault yourself (see from 
page 47). 
A technician who is called out to give advice will 
charge you, even if the appliance is still under 
guarantee. 
You can find your nearest customer service in the 
enclosed address list. Please provide customer 
service with the product number (E-Nr.) and the 
production number (FD) of the appliance. 
These numbers are shown on the rating plate which 
can be found on the frame of the open door and also 
on the identification plate, enclosed by a thick line, on 
the front of the machine behind the nameplate. 
Please note the two numbers in the space provided 
above.
In specifying the product number and production 
number of your appliance, you help us in our attempt 
to prevent unnecessary travelling and the associated 
extra costs.
Rating plate
E-Nr.FD
Product number Production number
 
						

							53
Installation instructions
Installing, connecting and transporting 
Safety instructions mRisk of injury! 
The washer-dryer is heavy. Take care when lifting it. 
Caution                                                                            
Frozen hoses may tear/burst. Do not install the 
washer-dryer in an area where there is a risk of frost or 
outdoors. 
The washer-dryer may be damaged. Do not lift the 
washer-dryer by its projecting parts (e. g. door). 
In addition to the safety information listed here, the 
local water and electricity supplier may have special 
requirements. 
If in doubt, have the appliance connected by a 
specialist. 
Standard 
accessories– Water-inlet hose. 
– Elbow for attaching the drainage hose e.g.  to the 
sink. 
– Power cord. 
Moisture in the drum is due to the final inspection 
which every washer-dryer undergoes before it leaves 
the factory. 
Depending on the connection situation, the following 
part is also required: 
– 1 hose clip 
Ø 24-40 mm (DIY store) is also 
required for connection to a siphon. 
The bag contains: 
– Covers for holes left by removing the transport 
bolts. 
 
						

							54
Useful tools The following tools are helpful: 
– Box wrench A/F 13 for removing the transportation 
bolts. 
– Spirit level for aligning the washer-dryer. 
Dimensions a = 600 mm 
b = 560 mm 
c = 850 mm 
Weight 67 kg 
Installation surface Appliance stability is important so that the washer-dryer 
does not wander during the spin cycles. 
The installation surface must be solid and level. Soft 
floor coverings, e. g. carpets or floor coverings with a 
foam backing are not suitable. 
If the washer-dryer is to be installed on a wooden floor: 
■If possible, install the washer-dryer in a corner. 
■Screw a water-resistant wooden board (at least 30 
mm thick) to the floor. 
■Secure the washer-dryer feet with fixing brackets*.
If the washer-dryer is to be installed on a base: 
■Secure the washer-dryer feet with fixing brackets*. 
*  Holding brackets (set) can be obtained from a 
specialist store or the Customer Service, order no. 
WMZ 2200. 
 
						

							55
Removing the 
transportation 
protection devices mCaution 
The transport bolts must always be removed before 
using the appliance for the first time and must be 
retained for any subsequent transport (e.g. when mov-
ing). 
■Release all screws A using the A/F 13 wrench until 
they can be moved freely.
■Remove the four spacers. They will fall to the floor 
when you tip the machine.
■Insert the covers. 
B
A
D
C
 
						

							56
Built-under or built-in 
appliance installation The appliance must be built under or built in prior to 
connecting the power supply. 
The appliance can be built into or under a kitchen work 
surface. For this purpose, a recess width of 60 cm is 
required. 
■The washer-dryer must only be installed under a 
one-piece worktop that is permanently attached to 
the surrounding cabinets. 
Caution                                                                            
For safety reasons in built-under installation, a cover 
plate* must be assembled by a specialist in place of 
the appliance cover plate. 
*  Cover plate (set) can be obtained from a specialist 
store or the Customer Service, order no. WMZ 
2420. 
 
						

							57
Hose and cable 
lengths 
Connection on left side 
Connection on right side 
Other hoses Available from specialist dealers: 
– Extended supply hose (approx. 2.20 m). 
mcmax.100mcmax.100
110cm~
~
100cm~
~
110cm~
~
mcmax.100mcmax.100
150cm~
~
140cm~
~
150cm~
~
 
						

							58
Connecting the water mRisk of electric shock! 
To prevent leaks or water damage, it is essential to
follow the instructions in this chapter! 
Water inlet hose  Caution                                                                            
Operate the washer-dryer with cold drinking water only. 
Do not connect to the mixer tap of an unpressurised 
hot-water apparatus. 
If in doubt, have the appliance connected by a 
specialist. 
Do not use a used inlet hose. Only use the inlet hose 
supplied or one which was purchased from an 
authorised specialist dealer. 
The water inlet hose must not be 
– kinked or crushed, 
– modified or severed (strength is no longer 
guaranteed). 
Plastic threads must only be tightened by hand. Do not 
remove the strainers from the water supply hose. 
Check the mains water pressure: 
– The water pressure should be between 1 and 10 
bars (when the tap is turned on, at least 8 litres of 
water is discharged per minute). 
– If the water pressure is higher, install a pressure 
reducing valve. 
Connect the water supply hose 
■to the rear panel of the washer-dryer and ... 
■to the tap. 
■After connecting the water inlet hose: Turn on the 
water tap completely, and check connection points 
for water-tightness. 
min. 10 mm