Bosch WVD 24460 User Manual

							31
Washing temperatureYou can change the default washing temperature. 
■Keep touching the temperature button °C Temp. 
until the desired temperature displays. 
²For different clothing, there are different pro-
grammes with respective temperature ranges.
Spin speed You can change the default spin speed. 
■Touch the Í Spin button until desired spin speed 
displays. 
²If setting $ (without final spin) has been selected, 
the washing remains in the final rinsing water. 
Before the laundry can be uploaded, the Drain [or 
Spin Í programme must be performed. Touch Spin 
Í button to select the desired spin speed or touch 
the “ Start/Pause ” button directly to start 
subsequent spin cycle with default spin speed. 
²The speed can be changed at any time by touching 
the Spin Í button until the new speed is displayed. 
Setting “$” (without final spin) is possible until the 
Rinse programme section starts. 
 
						

							32
Finish in timeBefore a programme starts, you can specify by how 
many hours later the programme is to be ended. 
Example of Easy-Care 40 °C 
programme: 
■Touch the 5 button, the display shows the 
minimum finish in time of the selected programme. 
Such as 1h, i.e.1 hours. 
²The minimum finish in time of different programmes 
are different. It depends on the duration of selected 
programme. 
■Touch the 5 button until the desired number of 
hours is displayed. 
²The finish in time can be set in 1-hour steps. The 
time can be delayed up to a maximum of 24h. If a 
finish in time of 24h has been set, the programme 
duration mode can be accessed by touching the 5 
button again. 
You can change other settings 
or 
■Touch the Start/Pause A button. The finish in 
time starts counting down. 
²The finish in time is counted down by the hour. 
When the finish in time has elapsed, the programme 
starts automatically and the programme duration is 
displayed. 
²Changes to the finish in time or an immediate start 
are possible. To do this: 
– Touch the Start/Pause A
 button. The 
programme duration time appears. 
– Touch the Start/Pause A
 button directly to 
start the programme immediately. If required, 
reset the finish in time. 
– Touch the Start/Pause A
 button. 
 
						

							33²If the programme sequence is changed by rotating 
the programme selector or the programme is 
cancelled, the preselected finish in time is also 
cancelled. The programme duration of the newly 
selected programme appears in the display. The 
finish in time must be reselected (see also chapter 
Changing the programme, page 36 and 
Cancelling the programme, page 36). 
²The laundry can be topped up at any time during the 
finish in time. Close the washer-dryer door. 
 
						

							34
Childproof lock You can secure your washer-dryer to prevent selected 
functions from being inadvertently changed. 
If the childproof lock has been selected: 
– no changes can be made while the programme is 
running, 
– the symbol 
@ flashes if a programme setting is 
inadvertently changed, 
– should the appliance be switched off and on while 
a programme is running, the programme will 
continue at the point at which it was interrupted, 
– when the programme ends, the duration time is 
showed as 0:01, the loading door cannot be 
opened, deactivate the childproof lock, the door 
can be opened while the display shows -0-. 
Activating the childproof 
lock
■Set the programme selector to the required 
programme and, if required, select other settings. 
■Load the laundry and close the loading door.
■Touch the Start/Pause A button. The programme 
starts. 
²Release the Start/Pause A
 button. 
Example of Easy-Care 40 °C 
programme: 
■Touch the 5 button and hold down (for approx. 5 
seconds) until the @
 symbol is displayed. 
■Release the 5 button, the childproof lock is 
activated, the symbol is permanently on. 
Deactivating the childproof 
lockThe childproof lock should be deactivated before 
making programme changes or ending programmes 
at selected programme. 
When a different programme has been selected,the 
@
  symbol will continue to flash and the childproof 
lock can be deactivated.But the running programme 
will be terminated and return to ready state.
■Touch the 5 button and hold down (for approx. 5 
seconds) until the @
 symbol goes out. 
²If there is a power failure, the childproof lock
remains on. 
5sec.
 
						

							35
SignalThe acoustic signal indicates:
– that the additional functions (buttons) have been 
switched on or off.
– individual programmes statuses (e.g. start of 
programme, end of programme), operating errors 
and faults.
Start the signal mode
■After setting, run the programme selector to “Off”, 
the volume of signal is stored
* If required,set repeatedly.
1. Set to “Off” 2. One step to right 3. keep selected and
5.release and find the number 
from 0 to 4 4. One step to right
6. One step to right
6. button signals*  7. Information signals*or
Set volume for...
 
						

							36
During washing/drying 
Changing the 
programmeIf you have accidentally selected the wrong 
programme 
■If the childproof lock is active, temporarily 
deactivate, see page 34. 
■Turn the programme selector to a newly selected 
programme. If required, change other settings. 
■Touch the Start/Pause A button. The programme 
starts. 
■If required, re-activate the childproof lock, see page 
34. 
Cancelling the 
programmeIf you would like to terminate a programme and remove 
the laundry: 
■If the childproof lock is active, deactivate, see page 
34.
■Turn the programme selector to Drain [, Spin Í 
or Rinse '
.
If required, select the desired spin speed (but not 
setting “$” (without final spin)). 
²If a programme is interrupted at a high temperature, 
Rinse '
 should be selected to cool down the 
laundry. 
■For drying programme, select time-dry 15 min 
cooling programm to cool down the laundry. 
■Touch the Start/Pause A button. 
■If required, switch on the childproof lock again.
■Wait until programme ends. 
■Deactivate the childproof lock. 
■Turn the programme selector to Off. 
 
						

							37
■Open the washer-dryer door. 
■Remove the laundry.
²If a programme was interrupted at a high 
temperature, such as drying programme, please 
do no open the washer-dryer door until the 
appliance has cooled down.
Pausing the 
programme If you would like to pause a runing programme without 
changing the sequence: 
■Touch the Start/Pause A button during washing 
cycle, the display shows PAUS (pause), if door 
open symbol }
 flashes at this moment means the 
door can be opened after 1 minute later, when the 
}
 symbol and OPEn come on, open the door if 
required, add/remove the laundry, close the door. 
■To continue the programme touch the Start/Pause 
A button again. 
²The pause function cannot be activated during 
drying cycle and water pressure detecting period. If 
a programme was paused at a high water level or 
temperature, the door open symbol does not 
appear. 
 
						

							38
When the programme has ended 
²Display panel: 
– All symbols on the programme status display have 
gone out, washing temperature, spin speed are 
displayed, 
– The programme duration is shown as -0-, 
– If the childproof lock is selected, the @ symbol is 
lit and the programme duration is shown as 0:01. 
Please deactivate the childproof lock, see page 34 
– If too much detergent was added, the *
 symbol 
illuminates.
²If the dry symbol ˆ
 flashes after the drying process 
has finished and the load is not dried adequately, 
consider the following for the next load to be dried: 
– Load the laundry to be dried according to 
recommended load. 
– Select “Spin” with the highest spin speed before 
laundry is dried. 
■Turn the programme selector to Off. 
or
Setting “ $
 ” (without final 
spin) selected²Display panel: 
– The '
 symbol, $ without final spin and the wash-
ing temperature are shown on the programme sta-
tus display, 
– The programme duration is shown as “- - - -”. 
– If the childproof lock is selected, the @
 symbol 
illuminates, 
– If detergent was overdosed, the *
 symbol 
illuminates.
 
						

							39
■If required, deactivate the childproof lock. 
■Select an additional programme Drain [, Spin Í; 
or touch the Start/Pause A
 button directly. 
■If required, activate the childproof lock. 
At the end of the additional programme: 
■If required, deactivate the childproof lock. 
■Turn the programme selector to Off. 
Removing the laundry ■Turn off the tap.
■Open the washer-dryer door. 
If the loading door cannot be opened: Wait 2 minutes 
(safety function is active) 
or 
there is still water in the washer-dryer if the “$” 
(without final spin) option was selected. 
Select the Drain [ or Spin Í programme and touch 
the Start/Pause A button. 
■Unload the laundry.
Caution                                                                            
Remove any foreign objects (e.g. coins, paper clips) 
from the drum and rubber seal - risk of rust! 
■Leave the washer-dryer door and detergent drawer 
open to allow the interior of the washer-dryer to dry. 
After drying: 
■Take the laundry out of the machine immediately to 
prevent creasing. This is particularly import with 
synthetic fabrics. 
Cottons + Linens 
– Cotton and linen items which have been dried to 
iron dry should be rolled together to prevent them 
from drying out completely before they are ironed. 
–Cupboard dry items must be smoothed out and 
folded up. 
Easy-care/synthetics
– Hang shirts and blouses individually on hangers.
 
						

							40
Special applications
Soaking ■Load laundry of the same colour. 
■Pour soaking agent into dispenser II according to 
the manufacturers instructions. 
■Set the programme selector to Cottons and the 
washing temperature 30°C. 
■Touch the Start/Pause A button. The programme 
starts. 
■After approx. 10 minutes, turn the programme 
selector to Off. The laundry is left to lie in the water. 
■Select a programme according to the required 
soaking time, the detergent solution is pumped out. 
²Only little detergent to be dispensed for the main 
wash. 
Starching The laundry must not be treated with fabric softener. 
■Insert the washing.
■Dose a quantity of starch for approx. 15 litres of 
water. Dissolve starch according to the 
manufac­turers instructions. 
■Turn the programme selector to Rinse '.
■Set the spin speed; even setting “$” (without final 
spin) is possible.
■Touch the Start/Pause A button. 
As soon as the water runs in: 
■pull out the detergent drawer a little and 
■pour starch solution into dispenser I. 
■Close the detergent drawer.
If setting “$” has been selected, select the Drain [
 
programme.