Home > Bosch > Home Security System > Bosch 7412 G User Manual

Bosch 7412 G User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Bosch 7412 G User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 101 Bosch manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							D9412G/D7412G | Program Entry Guide | 2.0 9000MAINEN | 11
    Bosch Security Systems | 1/04 | 47775E
    2.0 9000MAIN
    Use this programming module to define the
    operating characteristics that affect panel-wide
    functions. There are nine programming categories in
    this module: Phone, Phone Parameters, Routing,
    Enhanced Communications, Area Parameters,
    Command Center, User Interface, Function List, and
    Relay Parameters.
    2.1 Phone
    The control panel can dial up to four different
    telephone numbers when sending event reports. All
    telephone numbers use the same receiver format.
    Event report routing and communication protocols
    are discussed in Section 2.3 Routing.
    Phone 1
    Default:Blank
    Selection:Up to 24 characters (do not enter
    [SPACE])
    0 to 9 Numbers 0 through 9
    C 3-second pause
    D 7-second dial-tone detect.
    # or * Used for the same purpose as pressing
    this key on a telephone keypad when
    manually dialing. For example, an
    asterisk (*) may be needed to access
    your long distance service. Do not use
    these characters when pulse dialing.
    Blank Control panel dials no phone number.
    Programming this item Blank does not
    disable phone routing. To disable
    reporting to this phone, see Section 2.3
    Routing.
    This is the telephone number the control panel dials
    to contact the central station receiver when sending
    event reports. This number is Phone 1 referred to in
    the prompts in Section 2.3 Routing.The control panel is pre-programmed with a
    7-second dial tone detect period. When a dial tone is
    detected or the waiting period ends, the control
    panel begins to dial. To extend the dial tone detect
    period, place a D before the phone number. To
    insert a pause during or after dialing, use C in the
    number sequence. For example, if the control panel
    hangs up before it hears the Modem IIIa
    2 Ack tone
    from the D6500/D6600, program extra Cs after the
    phone number. The control panel waits on line for
    three extra seconds for each C programmed.
    Enter up to 24 of the following characters to define
    dialing characteristics.
    0101
    0101
    0101Using both phone data entry lines: The first
    line of the phone number data entry line
    must be filled (twelve characters) before
    you press [ENTER] to move on to the
    second line. If you enter characters on the
    second line, and there are less than twelve
    characters on the first line, the second line
    clears when you press [ENTER].
    Phone 2
    Default:Blank
    Selection:Up to 24 characters (do not enter
    [SPACE])
    See explanation of Phone 1. This number is Phone
    2, referred to in the prompts in Section 2.3 Routing.
    Phone 3
    Default:Blank
    Selection:Up to 24 characters (do not enter
    [SPACE])
    See explanation of Phone 1. This number is Phone
    3, referred to in the prompts in Section 2.3 Routing.
    Phone 4
    Default:Blank
    Selection:Up to 24 characters (do not enter
    [SPACE])
    See explanation of Phone 1. This number is Phone
    4, referred to in the prompts in Section 2.3 Routing. 
    						
    							D9412G/D7412G | Program Entry Guide | 2.0 9000MAINEN | 12
    Bosch Security Systems | 1/04 | 47775E
    2.2 Phone Parameters
    The program items in this category describe panel-
    wide characteristics for telephone dialing, receiver
    format, and supervision.
    Modem Format
    Default:Yes
    Selection:Yes or No
    Yes
    Radionics’ Modem IIIa2
    Communication Format: Reports
    identify points as 001 through 247 and
    passcode User ID codes as 000 through
    249 at the D6500/D6600 Receiver
    (unless 
    Point/User Flag is
    programmed Yes; see the 
    Point/User
    Flag
     prompt in this section). When
    reporting point events, Radionics’
    Modem IIIa
    2 Communication Format
    also sends point text to the
    D6500/D6600 as programmed in Point
    Assignments.
    No
    BFSK (2300 Hz or 1400 Hz
    acknowledgment tone).
    Central Station Receiver Format for
    Transmission of Reports: Modem format provides
    many reporting advantages over the BFSK format.
    See the D6500/D6600 Report Directory for more
    information about the effect of reporting formats.
    Modem Format must be set to Yes when
    sending events over a network to a D6600
    receiver (NetCom).
    0101
    0101
    0101If Modem Format is No, be sure to assign
    a number to identify Duress Reports in
    BFSK Duress Code in this programming
    section.
    Point/User Flag
    Default:Yes
    Selection:Yes or No
    Yes The control panel sends a flag with
    each report telling the D6500/D6600 to
    convert point numbers and User ID
    numbers to COMEX format. The
    conversions are shown in Table 6 and
    Table 7. No matter how the
    D6500/D6600 is programmed for
    output to the computer system, points
    and User ID numbers are converted
    when this item is Yes. (See the D6600
    Communications Receiver/Gateway
    Computer Interface Manual, Appendix C,
    Numbered Table and Note 1.)
    No The control panel does not send the
    flag. The D6500/D6600 outputs point
    numbers as 001 to 247 (rather than 100
    to 732) and User ID numbers as 000 to
    249 (rather than 000 to F08), as
    indicated in Table 6 and Table 7.
    This program item determines how point and User
    ID numbers are presented at the D6500/D6600
    display, printer, and computer RS-232 output.
    When 
    Modem Format is Yes, the control panel
    sends expanded Radionics’ Modem IIIa2
    Communication Format reports to the
    D6500/D6600. If your central station data files are
    not set up for point and User ID number reporting,
    you can use this program item to convert these
    numbers to COMEX Reports.
    When 
    Modem Format is Yes, the control panel
    sends expanded Radionics’ Modem IIIa2
    Communication Format Reports to the receiver.
    Point/User Flag affects Radionics’ Modem IIIa2
    Communication Format data as shown in Table 6.
    The Bosch Security Systems D6500/D6600 Receiver
    adds the leading zero in the User ID number with
    Point/User Flag programmed No. 
    						
    							D9412G/D7412G | Program Entry Guide | 2.0 9000MAINEN | 13
    Bosch Security Systems | 1/04 | 47775E
    Table 6: Modem IIIa2 Communication Format
    Data - User ID Numbers
    Point/User Flag
    NOPoint/User Flag
    YES
    000000
    001 to 005 001 to 005
    006 to 013601 to 608
    014 to 021 701 to 708
    022 to 029801 to 808
    030 to 037 B01 to B08
    038 to 045C01 to C08
    046 to 053 D01 to D08
    054 to 061E01 to E08
    062 to 069 F01 to F08
    070 to 249000
    Table 7: Modem IIIa2 Communication Format
    Data – Point Numbers
    Point/User Flag
    NOPoint/User Flag
    YES
    001 to 008100 to 800
    009 to 024 101 to 116
    025 to 040201 to 216
    041 to 056 301 to 316
    057 to 072401 to 416
    073 to 088 501 to 516
    089 to 104601 to 616
    105 to 120 701 to 716
    121 to 136801 to 816
    153 to 168 217 to 232
    169 to 184317 to 332
    185 to 200 417 to 432
    201 to 216517 to 532
    217 to 232 617 to 632
    233 – 247717 to 731
    Independent Zone Control Notice: When using
    Independent Zone Controls (IZC) to send
    Opening/Closing Reports by point, do not duplicate
    reporting independent point numbers with User ID
    Reports (see Section 3.1 Passcode/Token Worksheet). For
    example: If an IZC is connected to Point 8, User ID
    8 should not be used.D6000:Opening/Closing User ID numbers are
    identified at the receiver as ZONEs (same
    identification as independent points).
    Table 8: Zones
    User ID Number Zone
    1B
    2C
    3D
    4E
    5F
    66
    77
    88
    911
    92 2
    933
    94 4
    955
    96 0
    D6500/D6600 Receiving BFSK Format:
    Opening/closing User ID numbers are identified at
    the receiver as ZN (same identification as
    independent points). The ZN numbers are based on
    the tens digit of the User ID number. This only
    applies for Users 000 through 099. Users 100
    through 249 do not report in BFSK format.
    DTMF Dialing
    Default:Yes
    Selection:Yes or No
    Yes Dials the programmed phone
    number(s) using DTMF.
    No Pulse dialing only.
    Use dual-tone multi-frequency (DTMF) to dial the
    central station receiver phone number(s) for event
    reports, and/or the RPS. 
    						
    							D9412G/D7412G | Program Entry Guide | 2.0 9000MAINEN | 14
    Bosch Security Systems | 1/04 | 47775E
    Phone Supv Time
    Default:Blank
    Selection:Blank or 10 to 240
    Blank No phone line supervision.
    10 to 240 Enter the number of seconds (in 10
    second increments) you wish to
    supervise the phone line. After a faulted
    phone line restores, it takes the same
    amount of time to initiate restoral
    responses.
    Phone line trouble responses: Command centers
    display SERVC PH LINE # to indicate which
    phone line failed. The command center initiates a
    trouble tone if 
    Buzz on Fail is Yes and CC Trouble
    Tone
     is Yes.
    With dual phone lines (using the D928 Module), the
    restored phone line handles all messages regardless
    of the phone line’s number.
    Phone, Trouble, and Restoral Events report when
    they occur. They report also when a Diagnostic
    Report is initiated from a command center or by a
    Sked.
    Alarm On Fail
    Default:No
    Selection:Yes or No
    Yes Generate alarm responses when a
    phone line fails.
    No Phone failures report as trouble
    responses for Area 1 and/or the
    account number for Area 1.
    0101
    0101
    0101
    Phone Supv Time must be programmed to
    use this feature.
    Phone Failure Alarm Responses: The
    Alarm Bell relay for Area 1 activates. All
    Phone Event messages report as Area 1
    and/or the account number for Area 1.
    Buzz on Fail
    Default:No
    Selection:Yes or No
    Yes Generate panel-wide trouble tones and
    display PHONE FAIL # at command
    centers when a Phone Fail Event
    occurs.
    No Does not generate trouble tones at
    command centers when a Phone Fail
    Event occurs. PHONE FAIL # still
    displays.
    0101
    0101
    0101
    Phone Supv Time must be programmed to
    use this feature.
    De-selecting individual command
    centers for panel-wide trouble tones:
    Panel-wide trouble tones for programming
    CC can turn off individual command
    centers (based on their CC # 1 through 8)
    # Trouble Tone in Command Center
    Parameters as No.
    Two Phone Lines
    Default:No
    Selection:Yes or No
    Yes The D928 Dual Phone Line Module is
    installed. The LEDs on the D928 light
    to indicate primary or secondary line
    trouble and COMM FAIL.
    No No D928 Dual Phone Line Module.
    Use this program item when a D928 Dual Phone
    Line Module is connected to the control panel. Both
    lines must operate the same; either ground start or
    loop start.
    0101
    0101
    0101
    IMPORTANT! Program Phone Supv Time
    when using two phone lines.
    NFPA standards prohibit the use of ground
    start phone lines in systems monitoring
    Fire points. 
    						
    							D9412G/D7412G | Program Entry Guide | 2.0 9000MAINEN | 15
    Bosch Security Systems | 1/04 | 47775E
    BFSK Duress Code
    Default:0
    Selection:0 to 9
    If Duress Enable in Area Parameters is Yes and
    Modem Format in Phone Parameters is No, you
    must program a number to identify Duress Reports
    at the central station.
    Expand Test Rpt
    Default:No
    Selection:Yes or No
    Yes Report events listed in Routing Group
    Test Reports report to the central
    station if they are off-normal.
    No Does not report off-normal conditions
    for the events listed in the Routing
    Group Test Reports at test time.
    Use this program item to add system event
    information to scheduled Test Reports. Test Reports
    are set up as scheduled events. See Section 5.2 Skeds.
    This parameter is related only to Sked
    Function Code 9 (Test Report) and
    whether this Sked transmits Expanded
    Test Report information or not. It does not
    have any bearing on Sked Function Codes
    28 (Expanded Off-Normal Test Report)
    and 29 (Non-Expanded Off-Normal Test
    Report).
    Ground Start
    Default:Long
    Selection:Long or Short
    Long Standard duration of ground. Use this
    setting for most ground start telephone
    systems. The duration is 700
    milliseconds.
    Short Shorter duration of ground. Use this
    setting for telephone systems where
    specified. The duration is 250
    milliseconds.
    Some newer ground start telephone exchange
    switches require a shorter amount of time to initiate
    dial tone. If the control panel cannot initiate a dial
    tone on the ground start line with the default (long)
    setting, try the short setting.Press the [SPACE] bar to scroll through the
    selections. Press [ENTER] when the correct selection
    appears in the display.
    Use this program item only when the control
    panel is connected to ground start
    telephone lines. Ground start is not allowed
    on UL Listed systems.
    2.3 Routing
    Use routing to select full or partial groups of events
    which report to up to four different destinations.
    Routing includes choosing the most important
    destination (route number), the events reported to a
    single or multiple destination, and if the events fail,
    selecting a backup destination.
    2.3.1 Called Party Disconnect
    Telephone companies provide called party
    disconnect to allow the called party to terminate a
    call. The called party must go on hook (hang up) for
    a fixed interval before a dial tone is available for a
    new call. This interval varies with telephone
    company equipment. D9412G/D7412G firmware
    allows for called party disconnect by adding a 35
    second on hook interval to the dial tone detect
    function. If the control panel does not detect a dial
    tone in 7 seconds, it puts the phone line on hook for
    35 seconds to activate called party disconnect, goes
    off hook and begins a 7-second dial tone detect. If
    no dial tone is detected, the control panel dials the
    number anyway. Each time the number is dialed,
    the control panel records this as an attempt. After
    ten attempts, the control panel goes into
    communications failure and Comm Fail Route #
    displays on the command centers.
    2.3.2 Route Number Groups: Which Has the
    Highest Priority?
    To program a group, first choose a route number.
    The lower the route number, the higher priority that
    group has (for example, events reported for Route 1
    have a higher priority than Routes 2, 3, or 4 if each
    group tries to send a message at the same time). This
    becomes important when programming duplicate
    reports or choosing the events you want to ensure
    report first regardless of the number of events that
    need to report to multiple groups. Route 1 group
    primary device is the first destination the control
    panel attempts to dial if an event in that group must
    be reported. If the control panel is idle, any event
    generated for any group initiates a dialing sequence. 
    						
    							D9412G/D7412G | Program Entry Guide | 2.0 9000MAINEN | 16
    Bosch Security Systems | 1/04 | 47775E
    2.3.3 Programming a Primary and Backup
    Destination
    Each route number has an 
    R# Primary Device and
    an 
    R# Backup Device. In typical applications
    where two phone numbers are programmed, the 
    R#
    Primary Device
     destination is the phone number
    the route group attempts to dial first. If the
     R#
    Primary Device
     destination fails to connect to the
    central station receiver after two dialing attempts, the
    R# Backup Device destination is dialed. In
    addition, the control panel can be programmed so
    the 
    R# Primary Device and/or the R# Backup
    Device
     can be an SDI device, such as a D9133TTL-
    E Network Interface Module. The control panel can
    also be programmed to make only one attempt for
    the 
    R# Primary Device before attempting to send
    events using the 
    R# Backup Device.
    2.3.4 Enhanced Routing
    In previous versions, only Phone numbers 1 through
    4 could be programmed for the Primary and Backup
    Destinations. The D9412G/D7412G allow events to
    be transmitted to up to four additional SDI Paths.
    The D9133TTL-E Network Interface Module (with
    Ethernet) connects directly to the SDI Bus and
    occupies SDI Address 88. For additional information
    regarding the specific programming requirements for
    enhanced communications, see Sections 2.4 Enhanced
    Routing and 6.5 Enhanced Communications.
    2.3.5 Programming a Duplicate Report
    To allow an event within a group to report to
    multiple groups, the event should be Yes for each
    route number available. For instance, programming
    Fire Alarms for Route Group 1 and Route Group 2
    results in the fire alarms first reporting to Route
    Group 1 followed by a duplicate report to Route
    Group 2.2.3.6 Routing Destination Communication
    Failures
    When the 
    R# Primary Device fails to connect with
    the central station after one or two attempts (see
    RG# 1 Attempt in Section 6.6.1 Route Group
    Attempts), the 
    R# Backup Device phone number or
    SDI Path is attempted. The central station receives
    the original event with a COMM FAIL PHONE# =
    (1, 2, 3, or 4) if the 
    R# Primary Device destination
    is a phone number. If the 
    R# Primary Device is an
    SDI Path, the central station receives the original
    event with A COMM FAIL RG# SDI## (SDI Path
    1 = 88, SDI Path 2 = 89, SDI Path 3 = 90, SDI Path
    4 = 91). When all attempts to both the 
    R# Primary
    Device
     and R# Backup Device fail, a Comm Fail
    RG# Event is generated. Comm Restore Events are
    not generated.
    2.3.7 Message Prioritization within a Route
    Number
    The D9412G/D7412G Control Panels meet the
    digital reporting requirements for UL 864. Fire
    Alarm Events have the highest priority and are
    reported first for each group. The next highest
    priority events are in the following order: panic,
    duress, medical, intrusion alarm, supervisory, and all
    troubles and restorals.
    0101
    0101
    0101To comply with NFPA and UL864, you
    must program Route 1 to report only Fire
    Alarm Events to ensure the fastest
    reporting time.
    2.3.8 Dialing Attempts
    The D9412G/D7412G Control Panels have a
    prompt called 
    RG# 1 Attempt (see Section 6.6.1
    Route Group Attempts.).
    If this item is set to No, the control panel first makes
    up to six attempts to make contact using the primary
    device within a route group. If unsuccessful, it makes
    up to four attempts to make contact using the
    backup device before initiating a Comm Fail Report.
    When only one destination is programmed, the
    control panel makes ten attempts to contact that
    destination. Each group takes approximately 10
    minutes to go into Comm Fail.
    If this item is set to Yes, the control panel only
    makes one attempt (instead of two) to contact the
    primary device before attempting to contact the
    backup device. The route group still makes a total of
    ten attempts; however, the 
    R# Primary Device
    makes five attempts and then the R# Backup
    Device
     makes five attempts. 
    						
    							D9412G/D7412G | Program Entry Guide | 2.0 9000MAINEN | 17
    Bosch Security Systems | 1/04 | 47775E
    Route #
    Default:1
    Selection:1 to 4
    1 First group sent
    2 Second group sent
    3 Third group sent
    4 Fourth group sent
    Enter the number specifying the route group to
    program. The route represents the group you wish to
    send a group of reports. The groups are prioritized. 1
    is the first group to report and 4 is the last group to
    report. Each group has a primary and a backup
    device. The primary device is the first (most
    important) destination used to reach the
    programmed route within this group. The backup
    device is used if the primary device fails.
     R# Primary Device
    Default:Blank
    Selection:Blank, 1 to 4
    1 Phone 1 or SDI Path 1 is this group’s
    primary destination.
    2 Phone 2 or SDI Path 2 is this group’s
    primary destination.
    3 Phone 3 or SDI Path 3 is this group’s
    primary destination.
    4 Phone 4 or SDI Path 4 is this group’s
    primary destination.
    Enter the number specifying the primary device.
    R# Backup Device
    Default:Blank
    Selection:Blank, 1 to 4
    1 Phone 1 or SDI Path 1 is this group’s
    backup destination if the primary
    destination fails.
    2
    Phone 2 or SDI Path 2 is this group’s
    backup destination if the primary
    destination fails.
    3 Phone 3 or SDI Path 3 is this group’s
    backup destination if the primary
    destination fails.
    4 Phone 4 or SDI Path 4 is this group’s
    backup destination if the primary
    destination fails.
    Enter the number specifying the backup device. The
    backup device is used when the primary device fails
    to reach the programmed destination.
    View Events?
    Default:No
    Selection:Yes or No
    Yes
    Access each routing group and
    program individual events for this
    route group only (D5200).
    No
    Continue programming without
    viewing individual groups.
    The D5200 Programmer reveals the following sub-
    prompts. Leaving 
    View Events? as No allows the
    user to ignore a large area of programming that
    might not need to be changed. 
    						
    							D9412G/D7412G | Program Entry Guide | 2.0 9000MAINEN | 18
    Bosch Security Systems | 1/04 | 47775E
    Fire Reports
    Selecting Yes enables a report to be sent when the
    event occurs.
    Table 9: Diagnostic Reports
    Report Selections Description
    R# Fire AlarmYes, NoReports Fire Event.
    R# Fire Restore
    (Alarm)Yes, NoReports fire restoral
    from alarm.
    R# Fire MissingYes, NoReports missing Fire
    point.
    R# Fire Trouble
    Yes, NoReports fire trouble.
    R# Fire
    Supervis
    Yes, NoReports fire
    supervision.
    R# Fire Restore
    (T/M/S)Yes, NoReports fire restoral
    from trouble,
    missing, or bypass.
    R# Fire CancelYes, NoReports canceled
    fire alarm.
    R# Fire Sup
    MissYes, NoReport fire
    supervisory missing.
    R# Fire Supv
    Rest*Yes, NoReports restorals
    from Fire
    Supervision.
    *  This event is not reported when using BFSK format.
    Burglar Reports
    Selecting Yes enables sending a report when the
    event occurs.
    Table 10: Burglar Reports
    Report Selections Description
    R# AlarmYes, NoReport Burglar Alarm
    Event.
    R# Burg
    RestoreYes, NoReports non-fire
    restoral from trouble,
    missing, or
    supervisory.
    R# DuressYes, NoDuress Report.
    R# Missing
    AlarmYes, NoReports missing
    Alarm point.
    R# Usr Code
    Tmpr
    Yes, NoReports user code
    tamper.
    R# Trouble Rpt
    Yes, NoReports Trouble
    Event.
    R# Missing TrblYes, NoReports Missing
    Trouble Event.
    R# Non Fire
    SuprvYes, NoReports Non-fire
    Supervision Event.
    R# Pt Bus FailYes, NoReports point bus
    failure.
    R# Pt Bus Rstl
    Yes, NoReports restoral of
    point bus after failure.
    R# Non Fire
    Cncl
    Yes, NoReports canceled
    non-fire alarm.
    R# Alarm
    RestoreYes, NoReports non-fire
    restoral from alarm.
    R# Sup MissingYes, NoReports supervisory
    missing.
    R# Unverfied
    Evt†*Yes, NoReports Unverified
    Events for Cross
    points.
    † This event is not reported when using BFSK format.
    *  This event does not produce a corresponding Restoral
    Event.
    0101
    0101
    0101The Unverified Event is transmitted when a
    single point programmed in Cross Point
    Group faults into an alarm condition then
    restores before the Cross Point Time
    elapses. This event encompasses both
    Fire and Non-fire points. It is not, however,
    related to the Verify Time used for smoke
    detectors. 
    						
    							D9412G/D7412G | Program Entry Guide | 2.0 9000MAINEN | 19
    Bosch Security Systems | 1/04 | 47775E
    Restoral Reports are not sent if the
    control panel is reset after a point is
    bypassed and then the point is
    unbypassed. This is true for both Fire and
    Non-fire points.
    The 9000 Series Control Panels log a
    Ground Fault Event as Trouble Point 256.
    User Reports
    Selecting Yes enables a report to be sent when the
    event occurs.
    Table 11: User Reports
    Report Selections Description
    R# Point
    Bypass
    Yes, NoReports Point
    Bypass Event.
    R# Forced
    PointYes, NoReports Forced
    Point Event.
    R# Point OpenYes, NoReports Point
    Opening Event.
    R# Point Close
    Yes, NoReports Point
    Closing Event.
    R# Forced ArmYes, NoReports point forced
    armed.
    R# Fail To
    OpenYes, NoReports Fail to
    Open Event.
    R# Fail To
    Close
    Yes, NoReports Fail to
    Close Event.
    R# Ext Clos Tm
    Yes, NoReports Extend
    Close Time Event.
    R# Opening
    Rpt
    Yes, NoReports Opening
    Events.
    R# Forced
    CloseYes, NoReports Point
    Forced Close Event
    R# Closing RptYes, NoReports Closing
    Events.
    R# FC Perim
    InstYes, NoReports Forced
    Close Perimeter
    Instant Armed Event.
    R# FC Perim
    Delay
    Yes, NoReports Forced
    Close Perimeter
    Delay Armed Event.
    R# Perim Inst
    ArmYes, NoReports Perimeter
    Instant Armed Event.
    R# Perim Delay
    Arm
    Yes, NoReports Perimeter
    Delay Armed Event.
    R# Send User
    TextYes, NoReports user text. 
    						
    							D9412G/D7412G | Program Entry Guide | 2.0 9000MAINEN | 20
    Bosch Security Systems | 1/04 | 47775E
    Test Reports
    0101
    0101
    0101To send a single Test Report (R# Test
    Report), enable Sked Function Code #9
    (Test Report) in the Skeds section of the
    program.
    To expand this Test Report to include any
    off-normal point condition or other off-
    normal conditions of events listed in Diag
    Reports as a Non-status Event following a
    Test Report, Expand Test Rpt in Section
    2.2 Phone Parameters must be
    programmed Yes.
    Events R# Log Threshold, R# Log
    Overflow, and R# RAM Fail are added to
    the reports sent with Expanded Test
    Reports if they are enabled in RAM Reports
    and Expand Test Rpt is also enabled.
    To initiate a Status Report, which includes
    all R# S: ____ Events as a Status Event (as
    opposed to a Non-status Event), Sked
    Function Code #10 must be enabled in the
    Skeds section of the program.
    Reporting off-normal conditions as a Status
    Report following a Test Report is required
    by some automation systems. Reporting off-
    normal conditions as a Non-status Report,
    which follows a Test Report, is required for
    other automation systems.
    An off-normal condition is any point which is
    missing, trouble, supervisory, or in alarm (as
    opposed to normal). Also, points not
    cleared at the command center report as
    off-normal.
    Control Panels with Firmware version 6.30
    or higher can generate an Expanded Off-
    Normal Test Report by using Sked Function
    Code 28 or a Non-Expanded Off-Normal
    Test Report using Sked Function Code 29.
    To generate this event, one or more points
    must be in an off-normal state at the time
    the Sked executes. Expanded Off-Normal
    Test Reports include the Off Normal Test
    Report Event as well as events for any
    points that are in an off-normal state at the
    time the report is generated. Non-Expanded
    Off-Normal Test Report Events are only
    sent when a point is in the off-normal state
    but only sends the Off Normal Test Report
    Event.
    Table 12: Test Reports
    Report Selections Description
    R# S: AlarmYes, NoStatus Alarm Report
    R# S: Trouble
    Yes, NoStatus Trouble
    Report
    R# S:
    Supervised
    Yes, NoStatus Supervised
    Report
    R# Status
    ReportYes, NoStatus Report
    R# S: OpenYes, NoStatus Open Report
    R# S: Close
    Yes, NoStatus Close Report
    R# Test ReportYes, NoTest Report
    R# S: Perim
    InstYes, NoStatus Perimeter
    Instant Arm Report
    R# S: Perim
    Delay
    Yes, NoStatus Perimeter
    Delay Arm Report
    R# S: Fire Supv
    Yes, NoStatus Fire
    Supervision Report
    R# S: Fire
    Alarm
    Yes, NoStatus Fire Alarm
    Report
    R# S: Fire Trbl
    Yes, NoStatus Fire Trouble
    Report
    R# S: Msng
    Fire
    Yes, NoStatus Fire Missing
    Report
    R# S:
    MsngBurgTrYes, NoStatus Burg Missing
    Trouble Report
    R# S:
    MsngBurgAl
    Yes, NoStatus Burg Missing
    Alarm Report
    R# S:
    FireSpMsngYes, NoStatus Fire
    Supervision Missing
    Report
    R# S:
    SuperMsng
    Yes, NoStatus Non-fire
    Supervision Missing
    Report
    R# S:
    DrLeftOpenYes, NoStatus Door Left
    Open Report
     Diag Reports
    Selecting Yes enables sending a report when the
    event occurs. If the off-normal state of the following
    events (indicated with an *) still exist, they report
    when a Test Report (see the 
    Test Reports sub-
    prompt in Section 2.3.8 Dialing Attempts) is initiated
    and Expanded Test Rpt is programmed Yes. 
    						
    All Bosch manuals Comments (0)