Bissell 9500p Manual

www.bissell.com 800.237.769111
Operations
Carpet cleaning continued
6. Plug into a proper outlet and turn the power 
and heater switches to the on ( i )  
position. allow 1 minute for the built-in 
heater to warm-up before cleaning. the 
ProHeat 2X will be fully warmed and   
will provide optimal performance after   
a minute of continuous heated cleaning.
7.  cleaning strokes. While pressing the 
trigger, make one slow forward wet 
pass and another one back. Caution: 
Do not overwet. t ake care not to...

www.bissell.com 800.237.7691
Operations
12
Carpet cleaning continued
8c. lift the bottom portion of the tank; pour out 
dirty water in the sink through the triangular 
shaped opening in the corner of the tank.
Note: Check the red lint screen in 
the top of the tank and clean if 
necessary. You may notice hair & 
debris deposits on the carpet or in 
the tank that were loosened by the 
cleaning action. This debris should 
be picked up and thrown away.
8d.  fill the heavy duty bladder with clean 
hot tap...

www.bissell.com 800.237.769113
Operations
Cleaning with attachments
Your ProHeat 2X machine comes 
equipped with a hose and at least 
one attachment for cleaning stairs, 
upholstery, and more.
1. Important! if using to clean uphol-stery, check upholstery tags. 
A.  check manufacturer’s tag before clean-
ing. “W” or “Ws” on the tag means 
you can use your ProHeat 2X. if the tag 
is coded with an “X” or an “s” (with a 
diagonal stripe through it), or says “dry 
clean only”, do not proceed with any 
deep...

www.bissell.com 800.237.7691
Operations
14
 
8. Remove and rinse tools in clean, running 
water. dry and replace in the tool caddy.
9.  it is recommended that you suction clean 
water from a bowl to rinse out the hose. 
10.  before replacing lift end of hose and 
stretch out to ensure all water is cleared 
from hose.
11.  coil flex hose around the tool caddy.
12.  empty 2-in-1 water tank and rinse out,  
following the instructions on page 12.  
13.  Return Readyt ools dial to floor setting.
Deep reach...

www.bissell.com 800.237.769115
Operations
Stain removal
Do Not Delay! Attending to an  
accident soon after it occurs ensures 
the most optimal clean. Leaving it 
for an extended period of time may 
cause it to set and become  
permanent.
1. blot up liquids with an absorbent cloth or 
paper towels. White materials are recom-
mended because certain dyes may bleed 
and make the stain worse.
2.  gently scrape up any semi-solids with a 
spoon or spatula. do not use a knife or other 
utensil with sharp edges...

www.bissell.com 800.237.7691
Operations
16
Hard floor cleaning
Your ProHeat 2X model may have 
come with a hard floor attachment 
and 2X Hard Floor Solutions Formula. 
If not, these products are available 
for purchase by contacting the BISSELL 
Consumer Care department by phone 
or at the website. The hard floor tool 
provides effective cleaning for linoleum, 
vinyl, and tile floors. Caution: Do not 
use on unsealed hardwood floors.
1. Vacuum or sweep thoroughly to pick up 
any loose debris and pet...

www.bissell.com 800.237.769117
Maintenance and care  
Machine storage
once your cleaning is complete, make sure 
the 2-in-1 water tank is emptied, rinsed out, 
and dried before the next use. the formula 
tank can remain filled and ready to go.
Note: Store cleaner in a protected, 
dry area. Since this product uses 
water, it must not be stored where 
there is a danger of freezing. 
Freezing will damage internal  
components and void the warranty.
Machine care
For best results, a few simple steps can...

www.bissell.com 800.237.7691
Maintenance and care  
18
Machine care continued
6.  the inside of the end caps by the brush 
rolls can be wiped out with a clean paper 
towel, or, if a more thorough cleaning is 
desired, the end caps can be taken off 
using a Phillips head       screwdriver and 
rinsed clean. Replace after cleaning.
7.  any loose hair or debris can be pulled from 
the brush rolls and thrown away. for the 
most thorough clean before storage, follow 
directions on pages 18 & 19 for removal...

www.bissell.com 800.237.769119
Maintenance and care   
 
Brushes can be removed for cleaning 
or replacement as needed. 
1. follow small belt removal instructions on   
page 18.
2.  Remove brush rolls by pulling them off 
of the metal rods.
3.  Place cleaned or new brush rolls back 
onto the rods. make sure one washer is 
on each end of the rollers prior to sliding 
onto the rod. be sure to let the rod slide 
through the bushing to insure proper fit.
4.  Re-attach the long belt on the bottom to 
the cogs...

www.bissell.com 800.237.7691
Troubleshooting
www.bissell.com 800.237.769120Built-in heater ready light does not illuminate
Possible causes 
Remedies
1.  The heater switch is not turned ON ( I )  1.  Turn the heater switch ON ( I )
2.   The power switch is not turned ON ( I )  2.  Both switches must be ON ( I ) to activate the   
    heater ready light
Reduce Spray or No Spray
Possible causes  Remedies
1.  Water tank may be empty   1.  Fill heavy duty bladder with hot tap water
2.   Formula tank may be...