Bissell 9300-b Manual

w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 511
Ope\fat\bons
Carpet c\beaning continued
6. Plug into a proper outlet and turn the power 
and heater switches to the  on ( i ) posi -
tion.  allow 1 minute for the built-in heater 
to warm-up before cleaning.  the P\b oheat 
2X will be fully warmed and will pro\fide 
optimal performance after a minute of   
continuous heated cleaning.
7.  While pressing the trigger, make one slow 
forward wet pass and another one back. 
Caution: Do not overwet.  t...

w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 5
Ope\fat\bons
12
Carpet c\beaning continued
8c. lift the bottom portion of the tank; pour out 
dirty water in the sink through the triangular 
shaped opening in the corner of the tank.
Note: You may notice hair & debri\f 
depo\fit\f on the carpet or in the tank 
that were \boo\fened by the c\beaning 
action. Thi\f debri\f \fhou\bd be picked 
up and thrown away.
8d.   fill the hea\fy duty bladder with clean 
hot tap water, following instructions 1c...

w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 513
Ope\fat\bons
C\beaning with attachment\f
Your PROheat 2X machine come\f 
equipped with a ho\fe and at \bea\ft 
one attachment for c\beaning \ftair\f, 
upho\b\ftery, and more.
1. Important!  if using to clean uphol-
stery, check upholstery tags. 
A.  check manufacturer’s tag before clean -
ing. “W” or “W s” on the tag means 
you can use your P\b oheat 2X.  if the 
tag is coded with an “X” or an “ s” 
(with a diagonal stripe through it), or 
says “...

w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 5
Ope\fat\bons
14
 
8. \bemo\fe and rinse tools in clean, running 
water.  dry and replace in the tool caddy.
9.  it is recommended that you suction clean 
water from a bowl to rinse out the hose. 
10.  before replacing lift end of hose and 
stretch out to ensure all water is cleared 
from hose.
11.  coil flex hose around the tool caddy.
12.  empty 2-in-1 water tank and rinse out, 
following the instructions on page 12.  
13.  \beturn \beadyt ools dial...

w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 515
Ope\fat\bons
Stain remova\b
Do Not De\bay! Attending to an  
accident \foon after it occur\f en\fure\f 
the mo\ft optima\b c\bean. Leaving it 
for an extended period of time may 
cau\fe it to \fet and become   
permanent.
1.  blot up liquids with an absorbent cloth or 
paper towels. White materials are recom -
mended because certain dyes may bleed 
and make the stain worse.
2.  gently scrape up any semi-solids with a 
spoon or spatula.  do not use...

w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 5
Ope\fat\bons
16
Hard f\boor c\beaning
(Se\bect mode\b\f on\by)
Your PROheat 2X mode\b may have 
come with a hard f\boor attachment 
and 2X Hard F\boor So\bution\f Formu\ba. 
If not, the\fe product\f are avai\bab\be 
for purcha\fe by contacting the BISSELL 
Con\fumer Service\f department by 
phone or at the web\fite. The hard f\boor 
too\b provide\f effective c\beaning for \bino-
\beum, viny\b, and ti\be f\boor\f. Caution: Do 
not u\fe on un\fea\bed...

w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 517
Ma\bntenance and ca\fe  
Machine \ftorage
Once your c\beaning i\f comp\bete, 
make \fure the 2-in-1 water tank i\f 
emptied, rin\fed out, and dried before 
the next u\fe. The formu\ba tank can 
remain fi\b\bed and ready to go.
Note: Store c\beaner in a protected, 
dry area. Since thi\f product u\fe\f 
water, it mu\ft not be \ftored where 
there i\f a danger of freezing. 
Freezing wi\b\b damage interna\b  
component\f and void the warranty.
Machine...

w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 5
Ma\bntenance and ca\fe  
18
Machine care continued
6.  the inside of the end caps by the brush 
rolls can be wiped out with a clean paper 
towel, or, if a more thorough cleaning is 
desired, the end caps can be taken off 
using a Phillips head       screwdri\fer and 
rinsed clean. \beplace after cleaning.
7.  any loose hair or debris can be pulled from 
the brush rolls and thrown away.  for the 
most thorough clean before storage, follow 
directions...

w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 519
Ma\bntenance and ca\fe   
 
Bru\fhe\f can be removed for c\beaning 
or rep\bacement a\f needed. 
1. follow small belt remo\fal  instructions on 
page 18.
2.  \bemo\fe brush rolls by pulling them off 
of the metal rods.  Be carefu\b not to 
\bo\fe the \fma\b\b wa\fher at each 
end of the bru\fh ro\b\b\f.
3.  Place cleaned or new brush rolls back 
onto the rods.  make sure one washer is 
on each end of the rollers prior to sliding 
onto the rod.  be...

w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 5
T\foubleshoot\bng
20Bui\bt-in heater ready \bight doe\f not i\b\buminate
Po\f\fib\be cau\fe\f
  Remedie\f
1.	 The	heater 	switch 	is 	not 	turned 	ON 	\f 	I	 )	 1.	 Turn	the	heater	 switch	ON	\f 	I	 )
2.	 The 	\bower 	switch 	is 	not 	turned 	ON 	\f 	I	 )	 2.	 Both	switches	must	be	ON	\f 	I	 ) 	to 	activate 	the	 	
		 	 heater	ready 	light
Reduce Spray or No Spray
Po\f\fib\be cau\fe\f   Remedie\f
1.	 Water	tank 	may 	be 	em\bty	 1.	 Fill	heavy 	duty...