Bissell 9300-b Manual

							w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 511
Ope\fat\bons
Carpet c\beaning continued
6. Plug into a proper outlet and turn the power 
and heater switches to the  on ( i ) posi -
tion.  allow 1 minute for the built-in heater 
to warm-up before cleaning.  the P\b oheat 
2X will be fully warmed and will pro\fide 
optimal performance after a minute of   
continuous heated cleaning.
7.  While pressing the trigger, make one slow 
forward wet pass and another one back. 
Caution: Do not overwet.  t ake care 
not to run o\fer loose objects or edges of 
area rugs.  stalling brush may result in pre -
mature belt failure.  
Note: Your machine i\f equipped 
with a circuit breaker that wi\b\b 
automatica\b\by \fhut off the bru\fh if 
a \barge or \boo\fe object i\f caught 
in the bru\fh ro\b\b. If that happen\f, 
be \fure to unp\bug your machine, 
remove the foreign object, and 
then p\bug the machine back in to 
re\fet the circuit breaker. 
\belease the trigger and make one slow 
forward and backward pass o\fer the 
same area to remo\fe any residual   
dirty water and aid in drying. \bepeat 
cleaning passes until solution being 
pulled up appears clean.   continue 
passes without pressing the trigger until 
you can’t see any more water being 
pulled up. 
8.  \bemo\fe the tank from the base of the 
machine by lifting up on the tank carry 
handle.  carry like a bucket to a utility sink 
or outside where you will dispose of the 
dirty water.
8a.  unlatch the top of the tank from the 
bottom by lifting up on the tank latch   
located on the back of the tank.
8b.  \bemo\fe the top of the tank by lifting up on 
the handle. 
Note how the \bip on the top tank 
\feparate\f from the groove in the 
bottom tank. Thi\f p\bacement i\f 
important when putting the tank 
back together.
6.
WARNING: to reduce the risk of due to inter -
nal component damage, use only 
bissell  cleaning fluids intended 
for use with the deep cleaner.
Power Switc\f
Heater Switc\f
Keep p\benty of genuine 
BISSELL 2X formu\ba on hand 
\fo you can c\bean whenever it 
fit\f your \fchedu\be. A\bway\f u\fe 
genuine BISSELL deep c\beaning  
formu\ba\f. Non-BISSELL 
 
c\beaning \fo\bution\f may harm 
the machine and void the 
warranty.
8.
8b. 8a.  
						

							w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 5
Ope\fat\bons
12
Carpet c\beaning continued
8c. lift the bottom portion of the tank; pour out 
dirty water in the sink through the triangular 
shaped opening in the corner of the tank.
Note: You may notice hair & debri\f 
depo\fit\f on the carpet or in the tank 
that were \boo\fened by the c\beaning 
action. Thi\f debri\f \fhou\bd be picked 
up and thrown away.
8d.   fill the hea\fy duty bladder with clean 
hot tap water, following instructions 1c 
through 1e on page 10.
Note: Remember to \fecure the 
tank \batch in the back and te\ft   
to make \fure it i\f \fecure before 
picking up the tank. A\bway\f check 
the \beve\b of c\beaning formu\ba in 
the formu\ba tank at the \fame time, 
and refi\b\b a\f needed.
9.  Water rinse (recommended). \binsing is an 
optional step that can be done during the 
cleaning process or after the carpeted area 
has been completed.  switch to the water 
rinse setting, on the  custom  clean dial and 
follow the same path as you did for clean -
ing.  take care to do a forward (wet) stroke 
by depressing the trigger, and a backward 
(wet) stroke, followed by a forward and 
backward (dry) stroke, releasing the trigger. 
c ontinue this until the water you see coming 
up the nozzle is clear. ( see page 17 for 
more machine care tips.)8d. 8c.
9.
Keep p\benty of genuine 
BISSELL 2X formu\ba on hand 
\fo you can c\bean whenever it 
fit\f your \fchedu\be. A\bway\f u\fe 
genuine BISSELL deep c\beaning  
formu\ba\f. Non-BISSELL   
c\beaning \fo\bution\f may harm 
the machine and void the 
warranty.  
						

							w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 513
Ope\fat\bons
C\beaning with attachment\f
Your PROheat 2X machine come\f 
equipped with a ho\fe and at \bea\ft 
one attachment for c\beaning \ftair\f, 
upho\b\ftery, and more.
1. Important!  if using to clean uphol-
stery, check upholstery tags. 
A.  check manufacturer’s tag before clean -
ing. “W” or “W s” on the tag means 
you can use your P\b oheat 2X.  if the 
tag is coded with an “X” or an “ s” 
(with a diagonal stripe through it), or 
says “ dry  clean  only”, do not proceed 
with any deep cleaning machine.  do 
not use on \fel\fet or silk.  if manufactur -
er’s tag is missing or not coded, check 
with your furniture dealer.
B.  check for colorfastness in an incon -
spicuous place.
C.  if possible, check upholstery stuffing. 
c olored stuffing may bleed through 
fabric when wet.
D.  Plan acti\fities to allow upholstery 
time to dry.
E.  Vacuum thoroughly to pick up loose 
debris and pet hair.  use a \facuum 
with a brush attachment and a cre\fice 
tool to clean in fabric folds.
2.  follow the instructions on page 10 for filling 
the 2-in-1 water tank and the formula tank.
3.  set \beady tools dial to the " tools" 
setting.  this will allow spray and suction 
from the hose. 
4.  set  custom  clean dial for hea\fy traffic, 
normal clean, light clean, or water rinse 
as desired.
5.  attach the cleaning tool to the end of the hose.  
6.  Plug in and turn on the power switch and 
heater (if desired).
7.  clean by pressing the trigger to spray 
solution onto the area to be cleaned. 
s lowly mo\fe the tool back and forth o\fer 
the soiled surface. \belease the trigger to 
suction soiled water.  continue to clean in 
the area, working in small sections, until no 
more dirt can be remo\fed. \binse (optional) 
and suction as needed.   
Caution: Do no overwet.
Adsdfdd  ghg bvh
cvbbj  jkn hnbj  jkvh
gcg hhjj   jhffhl k llgh
Manufacturer’s tag
5.
WARNING: to reduce the 
risk of injury, be extra careful when 
cleaning stairs.  make sure machi ne is 
secure and le\fel.  
						

							w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 5
Ope\fat\bons
14
 
8. \bemo\fe and rinse tools in clean, running 
water.  dry and replace in the tool caddy.
9.  it is recommended that you suction clean 
water from a bowl to rinse out the hose. 
10.  before replacing lift end of hose and 
stretch out to ensure all water is cleared 
from hose.
11.  coil flex hose around the tool caddy.
12.  empty 2-in-1 water tank and rinse out, 
following the instructions on page 12.  
13.  \beturn \beadyt ools dial to floor setting.
Deep reach too\b attachment
(Se\bect mode\b\f on\by) 
Do Not De\bay! Attending to an acci-
dent \foon after it occur\f en\fure\f the 
mo\ft optima\b c\bean. Leaving it for an 
extended period of time may cau\fe 
it to \fet and become permanent.
1. follow the instructions on page 10 for filling 
the 2-in-1 water tank and the formula tank.
2.  follow instructions 3-6  on page 13 under 
" c leaning with attachments".
3.  set tool on stain and press the trigger to 
spray solution onto the area to be cleaned.
4.  Slowly move the tool \fack and forth 
over the soiled surface, keeping the tool 
in contact with the carpet.
5.  Release trigger and move tool slowly 
over the soiled area to suction up water 
and dirt.
6.  Continue to clean the area, working in 
small sections, until no more dirt can \fe 
removed. 
7.  Remove tool from hose when finished. 
Clean under warm water \fefore storing.
C\beaning with attachment\f continued
10.
3.
5.
7.  
						

							w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 515
Ope\fat\bons
Stain remova\b
Do Not De\bay! Attending to an  
accident \foon after it occur\f en\fure\f 
the mo\ft optima\b c\bean. Leaving it 
for an extended period of time may 
cau\fe it to \fet and become   
permanent.
1.  blot up liquids with an absorbent cloth or 
paper towels. White materials are recom -
mended because certain dyes may bleed 
and make the stain worse.
2.  gently scrape up any semi-solids with a 
spoon or spatula.  do not use a knife or other 
utensil with sharp edges because it could 
damage the carpet or upholstery.
3.  if the area has dried, remo\fe the 
remaining semi-solids and residue with a 
sweeper or \facuum.
4.  be sure to test any spot remo\fal formulas 
in an inconspicuous area first.  this is 
important as some dyes and materials 
could be damaged or discolored by 
cleaning sol\fents.  if such a change should 
occur, try a different solution or call a pro -
fessional.
5.  if cleaning on  berber carpeting, gently 
run your machine o\fer a hidden area.  if 
no fuzzing occurs, continue cleaning in 
soiled area.
6.  using the  bissell t ough  stain Pre cleaner, 
spray e\fenly o\fer soiled area.  do not 
o\ferwet. Wait 3-5 minutes.  gently work 
the solution by blotting area with a clean, 
damp, color safe cloth.
7.  clean using either the  FLOOR 
CLEANING,  or TOOLS setting on the 
\beadyt ools dial.  
						

							w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 5
Ope\fat\bons
16
Hard f\boor c\beaning
(Se\bect mode\b\f on\by)
Your PROheat 2X mode\b may have 
come with a hard f\boor attachment 
and 2X Hard F\boor So\bution\f Formu\ba. 
If not, the\fe product\f are avai\bab\be 
for purcha\fe by contacting the BISSELL 
Con\fumer Service\f department by 
phone or at the web\fite. The hard f\boor 
too\b provide\f effective c\beaning for \bino-
\beum, viny\b, and ti\be f\boor\f. Caution: Do 
not u\fe on un\fea\bed hardwood f\boor\f.
1.  Vacuum or sweep thoroughly to pick up 
any loose debris and pet hair.
2.  mo\fe any furniture, if needed.
3.  fill the formula tank to "W ate\b" line 
with water.  fill to "fo\bmula" line with 
bissell 2X Hard  floor solutions.
4.  fill the 2-in-1 water tank with hot tap 
water and set aside.
5.  attach the hard floor tool onto the bot -
tom of the machine by hooking it into 
the nozzle and swinging it down until it 
clicks into place. 
6.  set \beadyt ools dial to the "floo\b 
cleaning" setting.
7.  set the  custom  clean dial to  no\bmal 
clean.
8.  Plug into an outlet and turn the power 
switch and heater ON (  I ).
9.  slowly mo\fe the machine forward and 
back o\fer hard floor surface one time 
while depressing trigger.   
Caution: Do not overwet.
10.  \bepeat the motion without pressing the 
trigger using the hard floor tool to squee -
gee and suction up the dirty water.
11.  allow adequate time for floors to dry.
12.  \bemo\fe hard floor tool, rinse and dry 
before storing.
13.  \binse out the formula tank.
WARNING : to reduce the risk of fire, elec -
tric shock or injury unplug from 
outlet before ser\ficing.
WARNING :
to reduce the risk of fire   
and electric shock- when clean -
ing a hard floor, the  bissell bare 
floor tool kit 203-5642 must be 
used and it must only be used with 
bissell  Hard floor  solutions or 
bissell  2X Hard  floor  solutions 
cleaning fluid intended for use with 
this appliance.
5.  
						

							w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 517
Ma\bntenance and ca\fe  
Machine \ftorage
Once your c\beaning i\f comp\bete, 
make \fure the 2-in-1 water tank i\f 
emptied, rin\fed out, and dried before 
the next u\fe. The formu\ba tank can 
remain fi\b\bed and ready to go.
Note: Store c\beaner in a protected, 
dry area. Since thi\f product u\fe\f 
water, it mu\ft not be \ftored where 
there i\f a danger of freezing. 
Freezing wi\b\b damage interna\b  
component\f and void the warranty.
Machine care
For be\ft re\fu\bt\f, a few \fimp\be \ftep\f can 
a\f\fure your machine i\f we\b\b maintained 
after your c\beaning i\f comp\bete.
1.  flush your machine of any remaining 
residual solution.
A.  fill the 2-in-1 clean water tank with 
clean hot tap water.
B.  Plug your machine into a proper outlet 
and set the  custom  clean dial to the 
rinse setting.  turn the power on by 
pressing the power button. 
C.  \becline the handle and press the spray 
trigger for 15 seconds while making   
forward and backward passes on carpet. 
\belease the trigger to suction. \bepeat for 
another 15 seconds.  continue without 
pressing the trigger until there is no more 
water being suctioned.
2.  turn power and heater switches  off (o ). 
u nplug the machine and wrap the power 
cord.  empty the 2-in-1 water tank.
3.  \binse out 2-in-1 water tank, with running hot 
tap water, taking care to clean underneath 
the hea\fy duty bladder, and all around it.  
4.  the top half of the tank can be rinsed clean 
through the nozzle area.  also, pop out the 
red filter underneath the top half of the tank 
and rinse out. \beplace before putting the 
top and bottom hal\fes of the tank together.
5.  before you place the cleaned 2-in-1 water tank 
back onto the machine, simply unscrew the 
floor nozzle using a Phillips head screwdri\fer. 
t his can be rinsed out at the faucet.  then 
replace back onto the machine by starting 
from the bottom of the nozzle and hooking the 
tabs into the holes on the bottom sides of the 
machine.  secure into place with the screw.  
3 & 4
WARNING:   
To reduce the ris\f of fire, 
electric shoc\f or i\bjury 
u\bplug from outlet before 
servici\bg.
Filter
Tip:
let all parts dry com-
pletely before storing  
						

							w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 5
Ma\bntenance and ca\fe  
18
Machine care continued
6.  the inside of the end caps by the brush 
rolls can be wiped out with a clean paper 
towel, or, if a more thorough cleaning is 
desired, the end caps can be taken off 
using a Phillips head       screwdri\fer and 
rinsed clean. \beplace after cleaning.
7.  any loose hair or debris can be pulled from 
the brush rolls and thrown away.  for the 
most thorough clean before storage, follow 
directions on pages 18 & 19 for remo\fal 
and replacement of the brush rolls and belts.
8.  to clean attachments that may ha\fe been 
used, remo\fe from hose and rinse under 
clean, running water.  dry and replace 
attachment in the tool caddy.  clean the 
hose by suctioning clean water from the tap. 
b efore replacing, lift end of hose and stretch 
out to ensure all water is cleared from hose. 
\befer to page 14.
9.  after carpet is dry, \facuum again to 
remo\fe hair and fuzz.
 
Occa\fiona\b rep\bacement of one or 
both be\bt\f may become nece\f\fary. 
If that i\f needed, p\bea\fe fo\b\bow the 
in\ftruction\f be\bow.
1. turn off the machine, and unplug it from 
the outlet.
2.  \bemo\fe both the 2-in-1 water tank and 
the formula tank.  set aside.
3.  unscrew the front nozzle and remo\fe it. 
s et aside.
4.  turn the machine on its side. 
IMPORTANT: cord \fide down.
5.  \bemo\fe the clear end cap by unscrew-
ing the 2 black screws.  take care not to 
drop the screws into the unit.
6.  \bemo\fe 1 sil\fer screw.
7.  \bemo\fe pi\fot arm by gently lifting up.
8.  \bemo\fe small brush belt.
9.  \beplace small brush belt, and re\ferse 
steps abo\fe.3.
5.
4.
7.
9.
2.
6. 8.
WARNING: t o reduce the risk of fire, electric 
shock, or injury,turn power   
off  and disconnect plug from 
electrical outlet before performing 
maintenance or troubleshooting.
Sma\b\b be\bt remova\b and rep\bacement  
						

							w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 519
Ma\bntenance and ca\fe   
 
Bru\fhe\f can be removed for c\beaning 
or rep\bacement a\f needed. 
1. follow small belt remo\fal  instructions on 
page 18.
2.  \bemo\fe brush rolls by pulling them off 
of the metal rods.  Be carefu\b not to 
\bo\fe the \fma\b\b wa\fher at each 
end of the bru\fh ro\b\b\f.
3.  Place cleaned or new brush rolls back 
onto the rods.  make sure one washer is 
on each end of the rollers prior to sliding 
onto the rod.  be sure to let the rod slide 
through the bushing to insure proper fit.
4.  \be-attach the long belt on the bottom to 
the cogs of the small roller brushes.
5.  Place small belt o\fer back roller and 
metal cog.
6.  Place pi\fot arm in place and screw in 
place using the sil\fer screw.
7.  \be-attach clear end cap by tightening 
with the (2) black screws.
8.  \beturn front nozzle to front of unit, by 
latching from underneath and then 
securing with a screw.
  if you ha\fe any questions or are ha\fing   
trouble installing or replacing your 
belt(s) or brushes, please call  BISSELL 
Con\fumer Service\f  or \fisit 
www.bi\f\fe\b.ca for instructional \fideo.
2.
4.
6.
8. 3.
5.
7.
Bru\fh remova\b and \barge be\bt rep\bacement
WARNING: t o reduce the risk of fire, 
electric shock or injury, 
unplug from the outlet 
before ser\ficing.  
						

							w w w . b i s s e \f \f . c a  8 0 0 . 2 6 3 . 2 5 3 5
T\foubleshoot\bng
20Bui\bt-in heater ready \bight doe\f not i\b\buminate
Po\f\fib\be cau\fe\f
  Remedie\f
1.	 The	heater 	switch 	is 	not 	turned 	ON 	\f 	I	 )	 1.	 Turn	the	heater	 switch	ON	\f 	I	 )
2.	 The 	\bower 	switch 	is 	not 	turned 	ON 	\f 	I	 )	 2.	 Both	switches	must	be	ON	\f 	I	 ) 	to 	activate 	the	 	
		 	 heater	ready 	light
Reduce Spray or No Spray
Po\f\fib\be cau\fe\f   Remedie\f
1.	 Water	tank 	may 	be 	em\bty	 1.	 Fill	heavy 	duty 	bladder 	with 	hot 	ta\b 	water
2.	 Formula 	tank 	may 	be 	em\bty	 2.	 Fill	formula	 tank	with	BISSELL	 2X		
		 	 Formula	for	cleaning
3.	 Tank 	may	not	be	seated 	com\bletely	 3.	 Turn	\bower	OFF	\f0).	Remove 	and	reseat 	tank
4.	 Pum\b 	may	have 	lost	\brime.	 4.	 Turn	\bower 	OFF 	\f0) 	and 	then 	back 	ON 	\fI). 	Wait 	one 	minute,	 	
		 	 then	de\bress 	trigger
DirtLifter® PowerBru\fh doe\f not turn
Po\f\fib\be cau\fe\f   Remedie\f
1.	 The	belt	is	off 	or	broken	 1.	 Turn	\bower	OFF	\f	O 	)	and 	un\blug 	unit	from 	outlet. 	Follow		
		 	 instructions	on 	\bage 	19
2.	 The	 unit	is	in	 the	 u\bright	 \bosition	 2.	 Brushes	only	rotate	 when	unit	is	reclined	 using	the		
		 	 detent	\bedal
3.	 Circuit	breaker 	on 	machine 	may 	have 	tri\b\bed 	
3.	 Turn	the 	machine 	OFF 	\f 	O 	) 	and 	un\blug 	from 	outlet. 	Check	
		 	 to	see 	if 	foreign 	object 	is 	caught 	in 	brush 	roll. 	Remove		
		 	 object.	Plug 	machine 	in 	to 	reset 	circuit 	breaker
C\beaner not picking up \fo\bution
Po\f\fib\be cau\fe\f   Remedie\f
1.	 ReadyTools	dial 	may 	be 	at 	wrong 	setting	 1.	 Set	ReadyTools 	dial 	to 	either 	FLOOR 	CLEANING 	or 	TOOLS 	setting	
2.	 Tank	 may	not	be	seated	 \bro\berly	 2.	 Pick	u\b	both	 the	2-in-1	 water	tank	and 	formula 	tank 	and	 	
		 	 reseat	them 	so 	they 	fit 	snugly 	on 	the 	unit	
3.	 Tank	 may	not	be	assembled	 \bro\berly	 3.	 Check	to	make	 sure	the	"li\b"	 of	the	 nozzle	 is	securely	 	
		 	 hooked	into 	the 	groove 	on 	bottom 	of 	Tank 	\fsee 	\bage 	10)
4.	 Solution	 or	2-in-1	 water	tank	is	em\bty	 4.	 Check	fluid 	levels 	in 	heavy 	duty 	bladder 	and 	formula 	tank.	
5.	 2-in-1	 water	tank	has	\bicked	 u\b	maximum	 dirty	water	 5.	 Em\bty	 2-in-1	water	tank.	Refill	heavy	 duty	bladder	 with		
	and	 red	float	 door	has	closed.	 	 clean	hot	ta\b	water	 and	re\blace.	
6.	 Red 	float 	"door" 	in 	the 	tank 	may 	have 	closed 	as 	a 	result 	of 	bum\bing	 6.	 Turn 	the 	machine 	OFF	 \f	O	),	 allowing 	red 	float 	door 	to 	release	
an 	object 	or 	moving 	machine 	back 	and 	forth 	too 	quickly	 	 into 	the 	o\ben 	\bosition. 	Turn 	unit 	back 	ON	 \f	I	)	 to	 continue	 	
		 	 cleaning.	Be 	sure 	your 	forward 	and 	backward 	strokes 	are 	done	 	
		 	 at	a 	slower 	\bace.
Other maintenance or \fervice not inc\buded in the manua\b \fhou\bd be   
performed by an authorized \fervice repre\fentative.
Thank you for \fe\becting a BISSELL product.
P\bea\fe do not return thi\f product to the \ftore.             
For any que\ftion\f or concern\f, BISSELL i\f happy to be of 
\fervice. Contact u\f direct\by at 1-800-263-2535.