Bisell PROheat 2 7901J User Manual

11
Set up the machine following instructions in 
the Features section on pages 6-10.
Use any BISSELL Advanced Deep Cleaning Formula in the 
SmartMix Bottle when cleaning carpets, stairs or 
upholstery. Use clean water in the SmartMix Bottle for 
gentle cleaning or rinsing.
Choose the SmartMix setting to match the cleaning job.
Set the ReadyTools switch to either Tools/PreTreat or 
Floor Cleaning.
PreTreating is recommended to improve cleaning 
effectiveness for heavily soiled carpet in high traffic...

Repeat cleaning passes until solution being pulled up 
appears clean.
Continue passes without pressing the trigger until you 
can’t see any more water being pulled up. 
Note: Both the SmartMix Bottle and the clean 
water Tank must have liquid in them in 
order for the machine to spray. If one is 
empty, the machine will temporarily lose 
prime and will not spray cleaning solution 
or water.
After cleaning, you may want to turn the SmartMix Dial 
to the Water Rinse setting to give your carpeting a final...

13
Use your BISSELL Deep Cleaner as a Precleaner. With 
one of the tools attached to the Flex Hose, set the 
ReadyTools Dial to Tools/PreTreat and the Smart Mix 
Dial to the High Traffic setting. Spray the area with 
cleaning solution and allow the BISSELL Advance Deep 
Cleaning Formula to penetrate for 3-5 minutes.
Once the Precleaning is complete, use the attached tool 
to gently scrub the stain with back and forth strokes.
Allow to dry. Some difficult stains may require a 
second treatment.
Check...

14
Choose the 4” Upholstery Tool, the 3” Tough Stain Tool, or 
the Spraying Crevice Tool and connect to the Flex Hose.
Plug into a proper outlet and turn Power Switch ON.
While pressing the trigger, slowly move the spraying tool back 
and forth over the soiled surface. Release the trigger to suction 
soiled water.
Continue to clean soiled area, working in small sections, 
until no more dirt can be removed.
Caution: Do not overwet.
When the cleaning job is complete refer to the 
Maintenance section on...

First attach left side (short Tab) catching Tab over Floor Nozzle edge.
Gently bend long Tab (right side) outward to easily snap over 
edge of clear nozzle on left.
Set up machine following instructions in the Features
section on pages 6-10. Be sure to thoroughly rinse out any 
remaining BISSELL Advanced Deep Cleaning Formula from 
the SmartMix Bottle to prevent slippery linoleum, vinyl, and 
tile floors. Use BISSELL Floor Cleansing Formula in the 
SmartMix Bottle.
Check ReadyTools Dial - it should be...

16
Routine Maintenance Continued
Remove and rinse tools in clean, running water. Dry and 
replace on Tool Caddy.
Coil Flex Hose around storage brackets on Tool Caddy.
Remove Tank-In-Tank, dispose of dirty water. Refer to the 
Features section on Pages 8-9.
Rinse out Tank-In-Tank and replace on the machine; Clean out 
Lint Screen.
Clean out the Flow Indicator Filter each time it is used to ensure 
best cleaning performance. Unscrew the Flow Indicator Cap, lift 
out the Red Rotor and White Filter. Rinse...

17
Remove the black brush arm that holds the brush in place. 
Set the black brush arm aside (see illustration).
Remove the “toothed” Brush Belt from the brush then from 
the red pump pulley. Set the “toothed” Brush Belt and 
brush aside.
Locate and remove broken Pump Belt.
With the unit still on its side, loop one end of the 
replacement Pump Belt around the red pump pulley and 
then the other end around the silver motor shaft (see 
illustration). Do not twist the replacement Pump Belt.
Re-install the...

SmartTemp Ready Light Does Not Illuminate.
Possible Causes  Remedies
 The Power Switch is not turned ON.    Turn the Power Switch ON.
Reduced Spray OR No Spray.
Possible Causes Remedies
 Bladder may be empty.    Refill Bladder with clean hand hot tap water.
  SmartMix Bottle may be empty.    Fill with any BISSELL Advanced Deep Cleaning Formula for 
     cleaning or water if rinsing. 
 The Filter may be clogged.    Clean out Flow Indicator Filter, page 16. 
  Tanks may not be seated properly.    Turn...

19
Replacement Parts - BISSELL ProHeat II
23BRUSH
SUCTIO
N4
5678
9101113
14161719
20212223
12
15
If your BISSELL product should require service:
 In the UK call BISSELL Consumer Services at the number below and we will give you the location of a BISSELL Authorized Service 
Center in your area. For all other countries contact your local in country distributor for questions, service, or repair. 
If you have questions about your warranty or need replacement parts please contact the numbers below.
For UK...

20
©2003 BISSELL HOMECARE, Inc.
Grand Rapids, Michigan
All rights reserved. Printed in USA.
Part Number 310-5811
Rev 04/03
Visit our website at:
www.bissell.com
Scotchgard is a trademark of 3M
About Your Warranty
  This warranty gives you specific legal rights, and you may also have other rights which may vary from 
country to country. If you need additional instruction regarding this warranty or have questions regard-
ing what it may cover, please contact BISSELL Consumer Services by telephone, or...