Home > Bissell > Cleaner > Bisell PowerForce Turbo Bagless 82H5E User Manual

Bisell PowerForce Turbo Bagless 82H5E User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Bisell PowerForce Turbo Bagless 82H5E User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 201 Bissell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							11www.bissell.com 
    Check rotating floor brush and drive belt
    You should check your vacuum cleaner’s rotating 
    floor brush and drive belt regularly for wear or 
    damage. You should also clean the brush and 
    brush ends of string, hair and carpet fibers. These 
    can wrap around the brush and hamper its ability 
    to effectively clean your carpet.
     Also remove any 
    debris that has accumulated under the brush cover.
    1.  Unplug cleaner from electrical outlet.
    2.  Place handle in low position and turn vacuum  cleaner over so bottom side is up.
    3.  Remove the two screws from the brush  cover (as shown) with a Phillips head 
    screwdriver. Lift the brush cover off.
    4.  Grasp rotating floor brush at both ends and lift.
    5.  Clean strings, hair and other debris from  rotating floor brush, paying particular 
    attention to brush ends.
    6.  Clean strings, hair and other debris from motor  pulley and drive belt areas.
    7.  Check drive belt carefully for wear, cuts or  stressed areas. Replace if worn or damaged.
    8.  Check air passageway for obstructions.  Remove debris from this area.
    Replace drive belt
    Use only BISSELL Style 12 replacement 
    belts in your BISSELL PowerForce Turbo Bagless.
    1.  Unplug cleaner from electrical outlet.
    2.  With rotating floor brush removed from vacuum cleaner (Steps 1-4 of Check rotating floor brush 
    and drive belt), grasp old drive belt and remove 
    from motor pulley. Discard old drive belt.
    3.  Place new drive belt over motor pulley and  stretch other end over rotating floor brush in 
    the space between the bristles.
    4.  Place ends of rotating floor brush down into  slots on sides as shown.
    5.  Turn rotating floor brush by hand several times  in direction of motor pulley. If properly installed, 
    drive belt will center itself on rotating brush.
    6.  Reposition brush cover and replace two  screws. Make sure end of brush cover is 
    snapped into place.
    Maintenance and care
    Motor 
    Pulley
    Air Passageway
    Brush 
    Cover
    Brush 
    Cover
    ug110-4049_82H5_1008.indd   11 ug110-4049_82H5_1008.indd   11 10/14/08   2:40:45 PM
    10/14/08   2:40:45 PM 
    						
    							12www.bissell.com 
    Replace light bulb 
    Use only BISSELL replacement bulbs in your 
    BISSELL PowerForce Turbo Bagless.
    1.  Unplug cleaner from electrical outlet.
    2.  Using a flat screwdriver, table knife or coin, insert into the slot on the right of the lens 
    and gently push inner latch to the left, as 
    shown, to remove the lens.
    3.  Remove the bulb from the socket by grasping  bulb and pulling straight out. Install the new bulb 
    by pushing it gently into the socket until the bulb 
    snaps into place.
    5.  Reposition lens by inserting tab on left side and  then pushing the right side back into place.
    Clearing clog
    Low suction, poor pickup or no suction may be 
    due to a clog in the vacuum cleaner. If you notice 
    a change in the sound of the vacuum motor or a 
    reduction in the spinning action in the dirt 
    container, check for clogs.
    1.  Unplug cleaner from electrical outlet.
    2.  Empty dirt container.
    3.  Check upper tank and primary separator for build up or clogs. Check to make sure primary 
    separator is installed correctly. To unlock the 
    primary separator, grasp the rim and turn 
    toward the left. Pull straight down to remove. 
    If the primary separator is missing or not 
    locked into place, check and clear the tube in 
    the center of the dirt container and properly 
    install primary separator.
    4.  Remove the Twist ‘n Snap hose from the  vacuum by turning to the left. Check the 
    suction inlet, hose and hose wand for clogs. 
    Remove any clogs from the hose using a 
    long, narrow object such as a broomstick.
    5.  Check the foot hose for clogs. If needed,  remove the screw attaching the hose wand 
    base to the vacuum. Straighten the foot hose 
    and unclog with a long, narrow object such 
    as a broomstick.
    6.  If the clog persists, follow the instructions for  checking the rotating floor brush on page 11 
    and inspect the air passageway for obstructions.
    Maintenance and care
    Air Passageway
    Suction 
    Inlet
    Primary Separator
    Hose Wand 
    Base
    ug110-4049_82H5_1008.indd   12 ug110-4049_82H5_1008.indd   12 10/14/08   2:40:50 PM
    10/14/08   2:40:50 PM 
    						
    							Troubleshooting
    WARNING: To reduce the risk of electric shock, turn 
    power switch OFF and disconnect plug 
    from electrical outlet before performing 
    maintenance or troubleshooting.
    13www.bissell.com 
    Vacuum cleaner won’t turnPossible causes Remedies1.  Power cord not firmly plugged in  1.  Check electrical plug
    Vacuum cleaner wont pick up dirtPossible causes  Remedies1.  Incorrect height adjustment  1.  Adjust powerfoot to correct height setting
    2.  Hose not attached to suction opening  2.  Grasp Quick Release handle and firmly push 
         hose wand onto the suction opening.
    3.  Twist n Snap hose not securely attached  3.  Make sure Twist n Snap hose is snapped 
         into locked position
    4.  Crack or hole in hose  4.  Check hose and replace if needed
    5.  Broken or worn drive belt  5.  Replace drive belt, see page 11
    6.  Rotating floor brush bristles worn  6. Replace brush
    7.  Rotating floor brush jammed  7.  Remove brush and clean debris from brush ends
    8.  Clog in vacuum  8.  Follow instructions for clearing 
         clogs on page 12
    9.  Dirt container full  9.  Empty dirt container
    10.  Dirt container not installed properly  10. Position correctly and lock in place
    11.  Filters are dirty  11. Check and clean inner and outer circular 
         filters, pre-motor and post-motor filters
    12. Primary separator  missing or installed incorrectly  12. Check for a clog in the tube in the center of the 
         dirt container, clear and properly install 
         primary  separator
    13.  TurboBrush is clogged 
    or debris is  12. Maintain TurboBrush, see page 10 
    wrapped around the brush
    Tools wont pick up dirtPossible causes  Remedies1.  Crack or hole in hose  1.  Check hose and replace if needed
    2.  Vacuum hose, wand or tools clogged  2.  Follow instructions for clearing clogs on 
         page  12
    3.  Dirt container full  3.  Empty dirt container
    4.  Dirt container or upper tank not installed properly  4.  Position correctly and lock in place
    5.  Filters are dirty  5.  Check and clean inner and outer circular 
         filters, pre-motor and post-motor filters
    6. Primary separator  missing or installed incorrectly  6.  Check for a clog in the tube in the center of the 
         dirt container, clear and properly install 
         primary  separator
    Vacuum cleaner difficult to pushPossible causes   Remedies1.  Incorrect height adjustment  1.  Adjust powerfoot to correct height setting
    Visible dirt escaping from cleanerPossible causes  Remedies1.  Dirt container full  1.  Empty dirt container
    2.  Filters missing or installed incorrectly  2.  Check inner and outer circular filter and 
         post-motor filter for correct installation
    ug110-4049_82H5_1008.indd   13 ug110-4049_82H5_1008.indd   13 10/14/08   2:41:00 PM
    10/14/08   2:41:00 PM 
    						
    							Troubleshooting
    Visible dirt escaping from cleaner (continued)Possible causes  Remedies3.  Dirt container installed incorrectly  3.  Position correctly and lock into place
    4.  Filter cup installed incorrectly  4.  Remove dirt container and make sure filter 
         cup is fully attached
    Other maintenance or service not included in the manual should be performed by an  authorized service representative.
    Thank you for selecting a BISSELL product.
    Please  do  not  return  this  product  to  the  store.             
    14www.bissell.com 
    BISSELL Consumer Services
    If your BISSELL product should require service:In the UK, Australia or New Zealand, call BISSELL Consumer Services at the numbers below and we will give 
    you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local 
    in country distributor for questions, service, or repair. 
    If you have questions about your warranty or need replacement parts plea\
    se contact the numbers below.
    Or visit the BISSELL website - www.bissell.com
    When contacting BISSELL, have model number of unit available.
    Please record your Model Number: ___________________
    Please record your Purchase Date: ___________________
    Note: Please keep your original sales receipt. It provides proof of date of purchase in the event of a 
    warranty claim. See Warranty on page 16 for details.
    Please do not return this product to the store.
    For UK inquiries:
    Monday - Thursday  9 am — 5 pm 
      Friday  9 am — 4 pm 
    BISSELL Homecare (Overseas) Inc. The Boat Yard 
    105 Straight Road 
    Old Windsor 
    Berkshire, SL4 2SE
    United Kingdom 
    Telephone: 0870-225-0109  For Australian inquiries:
    Monday - Friday    9 am — 5 pm 
    BISSELL AUSTRALIA PTY LIMITED Unit 35
    15 Ricketts Road
    Mount Waverley, Victoria 3149
    Australia
    Telephone: 1-800-811-183 
    For all other inquiries: Monday - Friday    8 am — 4 pm 
    BISSELL Homecare, Inc.
    PO Box 1888
    Grand Rapids, MI 49501 USA
    Telephone: 01-616-453-4451 
    Fax: 01-616-453-1383
    For New Zealand inquiries:
    Monday - Friday    9 am — 5 pm 
    Parex Industries Ltd. 5 Tolich Place
    Henderson 0610
    Auckland
    New Zealand
    Telephone: 0800-247-735 
    ug110-4049_82H5_1008.indd   14 ug110-4049_82H5_1008.indd   14 10/14/08   2:41:01 PM
    10/14/08   2:41:01 PM 
    						
    							Replacement parts - BISSELL PowerForce Turbo Bagless
    Below is a list of common replacement parts. While not all of these parts may have come 
    with your specific model, they are available for purchase if desired.  
    Item  Part No.  Part Name
    1 32074  Style 7/9/10/12/14 Drive Belt (2-Pack)
    2  203-1297  Standard Headlight Bulb
    3 203-1056 Crevice  Tool
    4  203-1059  Combination Dusting Brush/Upholstery Tool 
    5 203-1068 Extension  Wand
    6 203-1216  Wire Reinforced Twist ‘n Snap Vacuum Hose (Select Models Only)
    7  203-5624  Wide Brush Roll
    8   32064  Style 9/10/12 Inner & Outer Circular Filter Set
    9  32065  Style 9/10/12 Inner Circular Filter only
    10  3205  Style 12 HEPA Media Filter
    11 203-1215 Pre-Motor Filter
    12 203-7170 TurboBrush Bracket
    13 203-7196 TurboBrush
    15www.bissell.com 
    12345
    67891 0                   
    111213
    ug110-4049_82H5_1008.indd   15 ug110-4049_82H5_1008.indd   15 10/14/08   2:41:02 PM
    10/14/08   2:41:02 PM 
    						
    							16www.bissell.com 
     This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have ques\
    tions regarding what it may 
    cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or 
    contact your local in country distributor.
     Limited One Year Warranty
     Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., will replace (with 
    new or remanufactured components), at BISSELL’s option, free of charge from the date of purchase by the 
    original purchaser, for one year any defective or malfunctioning part do to manufacturers d\
    efect. 
     This warranty applies to product used for personal, and not commercial or rental service. This warranty does  not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction 
    caused by negligence, abuse, or use not in accordance with the User’s Guide is not covered.
    BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL 
    DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. 
    BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. 
    *EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
    THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES 
    EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE 
    BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF 
    MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED 
    TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS 
    DESCRIBED ABOVE.
    ©2008 BISSELL Homecare, Inc
    Grand Rapids, Michigan
    All rights reserved. Printed in China
    Part Number 110-4049
    Rev 10/08
    Visit our website at:
    www.bissell.com
    Warranty - PowerForce Turbo Bagless
    For UK inquiries:
    Monday - Thursday  9 am — 5 pm 
      Friday  9 am — 4 pm 
    BISSELL Homecare (Overseas) Inc. The Boat Yard 
    105 Straight Road 
    Old Windsor 
    Berkshire, SL4 2SE
    United Kingdom 
    Telephone: 0870-225-0109  For Australian inquiries:
    Monday - Friday    9 am — 5 pm 
    BISSELL AUSTRALIA PTY LIMITED Unit 35
    15 Ricketts Road
    Mount Waverley, Victoria 3149
    Australia
    Telephone: 1-800-811-183 
    For all other inquiries: Monday - Friday    8 am — 4 pm 
    BISSELL Homecare, Inc.
    PO Box 1888
    Grand Rapids, MI 49501 USA
    Telephone: 01-616-453-4451 
    Fax: 01-616-453-1383
    For New Zealand inquiries:
    Monday - Friday    9 am — 5 pm 
    Parex Industries Ltd. 5 Tolich Place
    Henderson 0610
    Auckland
    New Zealand
    Telephone: 0800-247-735 
    ug110-4049_82H5_1008.indd   16 ug110-4049_82H5_1008.indd   16 10/14/08   2:41:19 PM
    10/14/08   2:41:19 PM 
    						
    All Bissell manuals Comments (0)

    Related Manuals for Bisell PowerForce Turbo Bagless 82H5E User Manual