Bisell CleanView PROheat 53U6E User Manual

www.bissell.com 11
Operations
Empty	the	2-in-1	 water	tank/
clean removable nozzle cont
5.  When finished, replace nozzle by slightly   
raising front of machine to line up slots on 
the base with the hooks on nozzle. Attach 
at base first and then click nozzle into 
place. 
NOTE:	 If	nozzle	 is	not	 attached	  
properly	 loss	of	suction	 will	occur.
6. To continue carpet cleaning, refer back 
to pages 10 through 11, beginning with 
“Fill the 2-in-1 water tank” on page 10.
If cleaning is complete, refer...

www.bissell.com 
Operations
12
7. Set the ReadyTools dial to the TOOLS setting. 
This will allow spray and suction from the hose. 
8.  Attach the cleaning tool of your choice to 
the end of the hose.
9.  Clean by pressing the spray trigger to spray  
solution onto the area to be cleaned. Slowly  
move the tool back and forth over the soiled  
surface. Release the spray trigger to suction dirty  
water. Continue to clean in the area, working in  
small sections, until dirt is removed.    
Caution:	 Do	Not...

13
Operations
Cleaning	with	Deep	 Reach™	 Tool	 
(select models only)
1.  Set tool on soiled surfaces and press the spray 
trigger to spray solution onto the soiled area 
to be cleaned. 
2.  Slowly move the tool back and forth over the 
soiled surface, keeping the tool in contact with 
the carpet. 
Release spray trigger and move tool slow-
ly over the soiled area to suction up water 
and dirt. 
4. Continue to clean the area, working in small 
sections, until no more dirt can be removed.
Hard Floor...

www.bissell.com 
Operations
Maintenance and care 
14
Hard Floor Cleaning continued
9.  Repeat the motion without pressing the 
spray trigger using the hard floor tool to 
squeegee and suction up the dirty water. 
10.  When finished, remove hard floor tool, 
rinse and let dry before storing. Refer 
to the Maintenance and care section on 
page 15 for machine clean up and  
storage instructions.Machine care
Machine	 care
For best results, a few simple steps can assure 
your machine is well maintained after...

www.bissell.com 15 
Maintenance and care 
Machine	care	continued
5a. Remove the white filter by grasping the post 
and pulling up and out of the unit. Rinse the 
filter under cold water. NOTE: Be careful 
not	to	drop	 the	filter	 into	the	sink	 or	
disposal.
5b.  Replace the white filter back into the filter 
area.  NOTE:	 Make	sure	the	white	 fil-
ter is seated properly before replac-
ing	 the	red	 solution	 filter	cap.
5c.  Replace the red solution filter cap   
and turn clockwise to tighten.
6....

www.bissell.com 
Troubleshooting
16Heat	
indicator	 light	does	 not	illuminate
Possible Causes  Remedies
1. The heater switch is not turned on.  1. Turn on the heater switch located on side of unit.
2.   The machine power switch is not turned on.  2.  Both switches must be on to activate the heat   
     indicator light.
Reduced spray OR no spray
Possible cause  Remedies
1.  Bladder may be empty.   1.  Turn power switch off; refill bladder with clean hand hot tap   
   water and formula.
2.  2-in-1 water...

www.bissell.com 17
Troubleshooting
DirtLifter	PowerBrush	 does	not	turn
Possible cause  Remedies1. The brush belt or pump belt is off or broken.  1. Refer to Remedy 4 on page 16 to check if brush belt or   
    pump belt is broken.
Cleaner	 not	picking	 up	solution
Possible cause  Remedies1.  ReadyTools dial may be on the wrong setting  1.  Set ReadyTools dial to either FLOOR CLEANING or TOOLS. 
  for the cleaning job. 
2.   Poor tool position. (Hand held attachments only).  2.  Adjust angle; apply more...

www.bissell.com 
Replacement parts  
Accessories and formulas
18Item 
Part No.  Part Name
 1 203-0104  Tank Assembly Complete
 2  203-0102  Tank Base
 3  203-0000  Removable Nozzle
 4  215-0628  Replacement Pump Belt (with instructions)
 5  015-0621  Replacement Brush Belt (with instructions)
 6  203-0105  Lint Screen
While	not	all	of	these	 parts	may	not	have	 come	 with	your	 machine,	 all	are 	
available	 to	you	 for	purchase,	 if	desired.
Item  Part No.  Part Name
 1 203-0149  Hard Floor Tool
 2...

 This warranty gives you specific legal rights, and you may also have oth\
er rights which 
may vary from country to country. If you need additional instruction regarding this warranty 
or have questions regarding what it may cover, please contact BISSELL Consumer Care by   
telephone, or regular post as described below, or contact your local in country distributor.
Limited	 Two	Year	 Warranty
 Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL will replace 
(with new or remanufactured...

©2013 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 160-0637
Rev 12/12
Visit our website at:
www.bissell.com
Scotchgard is a trademark of 3M
Microban
® is a registered trademark 
of Microban Products Company
BISSELL Consumer Care
www.bissell.com 20
If	 your	 BISSELL	 product	 should	require	 service:Call BISSELL Consumer Care at the numbers below and we will give you the\
 location of a 
BISSELL Authorized Service Center in your area. If you have questions...