Bisell CleanView PROheat 53U6E User Manual

							www.bissell.com 11
Operations
Empty	the	2-in-1	 water	tank/
clean removable nozzle cont
5.  When finished, replace nozzle by slightly   
raising front of machine to line up slots on 
the base with the hooks on nozzle. Attach 
at base first and then click nozzle into 
place. 
NOTE:	 If	nozzle	 is	not	 attached	  
properly	 loss	of	suction	 will	occur.
6. To continue carpet cleaning, refer back 
to pages 10 through 11, beginning with 
“Fill the 2-in-1 water tank” on page 10.
If cleaning is complete, refer to the 
“Maintenance and care” section on  
page 15.
ReadyTools™
Your deep cleaner comes equipped with a 
hose and at least one attachment for clean-
ing stairs, upholstery, and more.
Important!	 If	using	 the	machine	 to	
clean	 upholstery,	 check	upholstery 	
tags.
1.  Check manufacturer’s tag before cleaning. 
“W” or “WS” on the tag means you can 
use your deep cleaner. If the tag is coded 
with “X” or “S” (with a diagonal strike 
through), or says “Dry Clean Only,” do 
not proceed. Do not use on velvet or silk. If 
manufacturer’s tag is missing or not coded, 
check with your furniture dealer. 
2.  Check for colourfastness in an inconspicu-
ous place.
3.  If possible, check upholstery stuffing. 
Coloured stuffing may bleed through fabric 
when wet.
4.  Plan activities to give upholstery time to 
d r y.  
5.  Vacuum thoroughly to pick up loose 
debris and pet hair. Use a vacuum with 
a brush attachment and a crevice tool to 
clean in fabric folds and tufts.
6.  To begin cleaning with attachments,  
follow the instructions on page 10 for  
filling the 2-in-1 water tank.
5.
Adsdfdd  ghg bvh
cvbbj  jkn hnbj  jkvh
gcg hhjj   jhffhl k llgh
Manufacturer’s tag  
						

							www.bissell.com 
Operations
12
7. Set the ReadyTools dial to the TOOLS setting. 
This will allow spray and suction from the hose. 
8.  Attach the cleaning tool of your choice to 
the end of the hose.
9.  Clean by pressing the spray trigger to spray  
solution onto the area to be cleaned. Slowly  
move the tool back and forth over the soiled  
surface. Release the spray trigger to suction dirty  
water. Continue to clean in the area, working in  
small sections, until dirt is removed.    
Caution:	 Do	Not	 Overwet.
10.  When finished cleaning, remove and 
rinse tool(s) in clean, running water.  
11.  It is recommended that you suction clean 
water from the tap to rinse out the hose. 
12.  Before wrapping hose onto tool rack, lift 
end of hose and stretch out to ensure all 
water is cleared from hose.
ReadyTools™ continued
13. Wrap flex hose around tool rack.
14.  Empty 2-in-1 water tank and rinse out,  
following instructions on page 12.
15.  If the ReadyTools dial becomes difficult to 
turn, the diverter assembly that holds the 
dial may need to be cleaned. To clean, first 
remove nozzle and locate screw that holds 
the diverter assembly in place. With a Phillips 
screwdriver, remove the screw and set aside.
16.  Remove diverter assembly; hold under running 
water making sure water flows through and 
around the dial. Turn the dial about 10 times 
clockwise and 10 more times counter   
clockwise. This should free up any debris.
17.  Wipe diverter assembly with a soft cloth and 
replace back on machine. Replace nozzle.
18.  Return ReadyTools dial to FLOOR 
CLEANING setting.
7.
11.
15. 12.
16.
Run water 
through here Screw  
						

							13
Operations
Cleaning	with	Deep	 Reach™	 Tool	 
(select models only)
1.  Set tool on soiled surfaces and press the spray 
trigger to spray solution onto the soiled area 
to be cleaned. 
2.  Slowly move the tool back and forth over the 
soiled surface, keeping the tool in contact with 
the carpet. 
Release spray trigger and move tool slow-
ly over the soiled area to suction up water 
and dirt. 
4. Continue to clean the area, working in small 
sections, until no more dirt can be removed.
Hard Floor Cleaning
Your deep cleaner may have included a hard 
floor tool and 2X Hard Floor Solutions. The hard 
floor tool provides effective cleaning for linoleum, 
vinyl, and tile floors.   
Caution: Do not use on unsealed   
hardwood	 floors.
1.  Thoroughly vacuum or sweep floor to pick 
up any debris.
NOTE: 	Prior	 to	filling	 with	formula 	
and	 water	 be	sure	 all	carpet	 cleaning 	
formula	 is	thoroughly	 rinsed	from	the	
2-in-1	 water	 tank.
2. Fill BISSELL Hard Floor Solutions to the  
indicated fill line in the built in measuring 
cup and pour into mouth of bladder.
3.  Fill the bladder with clean hand hot tap 
water and set aside.
4.  Attach the hard floor tool to the bottom of 
the machine by hooking it into the nozzle 
and swinging it down until it clicks into 
place. 
5.  Be sure the ReadyTools dial is set to  
FLOOR CLEANING.
6.  Plug into an outlet and turn the power on.
7.  Plan your cleaning route to leave an exit 
path. Be sure to allow adequate time for 
floors to dry. 
8.  While pressing the spray trigger, make 
one slow forward wet pass and another 
back.Caution:	 Do	Not	 Overwet.
1.
3.
4.  
						

							www.bissell.com 
Operations
Maintenance and care 
14
Hard Floor Cleaning continued
9.  Repeat the motion without pressing the 
spray trigger using the hard floor tool to 
squeegee and suction up the dirty water. 
10.  When finished, remove hard floor tool, 
rinse and let dry before storing. Refer 
to the Maintenance and care section on 
page 15 for machine clean up and  
storage instructions.Machine care
Machine	 care
For best results, a few simple steps can assure 
your machine is well maintained after cleaning 
is complete.
1. Flush your machine of any remaining   
residual solution.
  a. Fill the 2-in-1 clean water tank   
(bladder)  with clean hot tap water.
  b. Plug your machine into a proper outlet 
and set the ReadyTools dial to the "FLOOR 
CLEANING" setting. Turn the power on by 
pressing the power button.
  c. Recline the handle and press the spray 
trigger for 15 seconds while making forward 
and backward passes on carpet. Release 
the trigger to suction. Repeat for another 15 
seconds. Continue without pressing the trigger 
until there is no more water being suctioned.
2.  Turn power switch off. Unplug the machine 
and wrap the power cord. 
3.  After emptying the 2-in-1 water tank, rinse 
with running hot tap water, taking care to 
clean underneath and around the heavy duty 
bladder. Clean out red lint screen (located 
on tank lid). Removable nozzle may be 
rinsed if necessary.
4.  Before you place the 2-in-1 water tank back 
onto the machine, remove the red solution 
filter cap (on the base of the machine). 
Remove the cap by inserting a coin or a flat 
head screwdriver into the slot on the top. 
Turn counter clockwise to unscrew.  
WARNING:  To reduce the risk of electric   
shock, or injury, unplug from   
the outlet before servcing.
4.  
						

							www.bissell.com 15 
Maintenance and care 
Machine	care	continued
5a. Remove the white filter by grasping the post 
and pulling up and out of the unit. Rinse the 
filter under cold water. NOTE: Be careful 
not	to	drop	 the	filter	 into	the	sink	 or	
disposal.
5b.  Replace the white filter back into the filter 
area.  NOTE:	 Make	sure	the	white	 fil-
ter is seated properly before replac-
ing	 the	red	 solution	 filter	cap.
5c.  Replace the red solution filter cap   
and turn clockwise to tighten.
6.  Replace the 2-in-1 water tank on   
the machine.
7.  Any loose hair or debris can be pulled from 
the brush roll and thrown away.  
8.  To clean attachments, remove from hose 
and rinse in clean, running water. Dry 
before storing. Clean the hose by suction-
ing clean water from the tap. Before wrap-
ping back on machine, lift end of hose and 
stretch out to ensure all water is cleared 
from hose. Refer to page 13.  
9. 
Wipe the machine’s exterior with a soft cloth.
10.  After carpet is dry, vacuum again to remove 
hair and fuzz
Machine	 storage
Put the unit away in a closet or basement for 
the next use. Store cleaner in a protected, dry 
area. Since this product uses water, it must not 
be stored where there is a danger of freezing. 
Freezing will damage internal components and 
void the warranty. 5a.  
						

							www.bissell.com 
Troubleshooting
16Heat	
indicator	 light	does	 not	illuminate
Possible Causes  Remedies
1. The heater switch is not turned on.  1. Turn on the heater switch located on side of unit.
2.   The machine power switch is not turned on.  2.  Both switches must be on to activate the heat   
     indicator light.
Reduced spray OR no spray
Possible cause  Remedies
1.  Bladder may be empty.   1.  Turn power switch off; refill bladder with clean hand hot tap   
   water and formula.
2.  2-in-1 water tank may not be seated properly.  2. Turn power switch off; remove tank and reseat. 
3.    Pump may have lost prime.  3. Turn power switch off; after 1 minute turn on and depress   
   spray trigger.
4.  The pump belt may be broken.  4. Turn power switch off and unplug from the outlet. To check   
   if a pump belt has broken, you will need a flat head   
   screwdriver. A. Insert the blade end into the slot of the   
   belt access door to release. Examine the belt for breakage.   
   You should be able to see the pump belt looped around   
   the motor shaft. If it is broken or missing, please refer to   
   Replacement Parts on page 18. A replacement belt may be   
   ordered by calling BISSELL Consumer Services. Complete   
   installation instructions will accompany the replacement belt.   
   B. When replacing belt access door be sure to line up slots of   
   belt access door with slots in machine, slide door into place and   
   snap shut.
WARNING:  To reduce the risk of electric shock,   
or injury, unplug from the outlet   
before servcing.
Slots
A.
B.
Pump Belt  
						

							www.bissell.com 17
Troubleshooting
DirtLifter	PowerBrush	 does	not	turn
Possible cause  Remedies1. The brush belt or pump belt is off or broken.  1. Refer to Remedy 4 on page 16 to check if brush belt or   
    pump belt is broken.
Cleaner	 not	picking	 up	solution
Possible cause  Remedies1.  ReadyTools dial may be on the wrong setting  1.  Set ReadyTools dial to either FLOOR CLEANING or TOOLS. 
  for the cleaning job. 
2.   Poor tool position. (Hand held attachments only).  2.  Adjust angle; apply more downward pressure.
3.   Removable nozzle may not be properly attached.  3.  Make sure nozzle is on correctly by slightly raising front   
   of machine to line up slots on the base of the machine   
   with the hooks on nozzle. Attach at base first and   
   then click nozzle into place. Refer to image 5 on page 12.
4.  2-in-1 water tank lid is not properly installed.  4. Re-install lid; refer to the images on page 10. 
5.  2-in-1 water tank is not properly seated.  5. 2-in-1 water tank must be firmly seated to function; remove   
   and reseat 2-in-1 water tank. 
6.  2-in-1 water tank has picked up maximum dirty water.  6. Empty 2-in-1 water tank and refill, refer to the Operation   
   section.
7.  The lint screen may be clogged.  7. Clean out lint screen. Refer to page 12.
Other	 maintenance	 or	service	 not	included	 in	the	 manual	 should	be	 
performed	 by	an	 authorized	 service	representative.
Thank	you	for	selecting	 a	BISSELL	 product.
Please	do	not	 return	 this	product	 to	the	 store.               
						

							www.bissell.com 
Replacement parts  
Accessories and formulas
18Item 
Part No.  Part Name
 1 203-0104  Tank Assembly Complete
 2  203-0102  Tank Base
 3  203-0000  Removable Nozzle
 4  215-0628  Replacement Pump Belt (with instructions)
 5  015-0621  Replacement Brush Belt (with instructions)
 6  203-0105  Lint Screen
While	not	all	of	these	 parts	may	not	have	 come	 with	your	 machine,	 all	are 	
available	 to	you	 for	purchase,	 if	desired.
Item  Part No.  Part Name
 1 203-0149  Hard Floor Tool
 2  203-6651  3" Tough Stain Tool
 3  203-6653  4" Upholstery Tool
 4  203-6654  6" Stair Tool
 5  203-6652  Powered TurboBrush ™
 Hand Tool
 6  203-0116  Spraying 2-in-1 Crevice Tool w/Brush
 7  203-6655  Spraying Crevice Tool
 8  203-8113  Deep Reach
™ Tool  
 9  210-3040  Mesh Tool Storage Bag
10  81L5-E  1.5 L 2X Wash & Protect Professional Formula w/ Scotchgard
™ Protector
11   66W9-E  1.5 L 2X Wash & Protect Pet Stain & Odour Formula w/ Scotchgard ™
 Protector
12  92F4-E  1.5 L 2X Wash & Protect Fresh Fragrance Formula w/ Scotchgard ™
 Protector
1 3  12W4-E  1.5 L 2X Wash & Protect Spring Breeze Fragrance Formula w/   
   Scotchgard™
 Protector
14  33D2-E  1.5 L 2X Wash & Protect Lavender Fragrance Formula w/ Scotchgard ™
 Protector
15  56L9-E  473 mL 2X Hard Floor Solutions 
16  0400-E  651 mL Tough Stain Precleaner
  
1 23456
1
6
13
2
7 8
14
3
9
15
4
11
16
5
12
10
Note: Additional BISSELL formula options may be available at your local \
retailer.  
						

							 This warranty gives you specific legal rights, and you may also have oth\
er rights which 
may vary from country to country. If you need additional instruction regarding this warranty 
or have questions regarding what it may cover, please contact BISSELL Consumer Care by   
telephone, or regular post as described below, or contact your local in country distributor.
Limited	 Two	Year	 Warranty
 Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL will replace 
(with new or remanufactured components), at BISSELL’s option, free of charge from the date 
of purchase by the original purchaser, for two years any defective or malfunctioning part 
do to manufacturers defect. 
  This warranty applies to product used for personal, and not commercial o\
r rental service. 
This warranty does not apply to fans or routine maintenance components s\
uch as filters, 
belts, or brushes. Damage or malfunction caused by negligence, abuse, or\
 use not in 
accordance with the User’s Guide is not covered.
*EXCEPTIONS	 AND	EXCLUSIONS	 FROM	THE	TERMS	 OF	THE	 LIMITED	 WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR 
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING 
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE 
LIMITED TO THE TWO YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE 
ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE 
PURCHASE PRICE OF THE PRODUCT. 
www.bissell.com 
19
Warranty - BISSELL CleanView® ProHeat®
For UK inquiries:
Monday - Thursday     9 am — 5 pm 
Friday      9 am — 4 pm 
BISSELL Homecare (Overseas)  
Ground Floor  
226 Berwick Avenue  
Slough  
Berkshire, SL1 4QT  
United Kingdom 
Telephone: 0844 888 6644 For	
all	other	 inquiries:
Monday - Friday     8 am — 4 pm 
BISSELL	 Homecare,	 Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01 616 453 4451  
Fax: 01 616 453 4451
Note: Additional BISSELL formula options may be available at your local \
retailer.  
						

							©2013 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 160-0637
Rev 12/12
Visit our website at:
www.bissell.com
Scotchgard is a trademark of 3M
Microban
® is a registered trademark 
of Microban Products Company
BISSELL Consumer Care
www.bissell.com 20
If	 your	 BISSELL	 product	 should	require	 service:Call BISSELL Consumer Care at the numbers below and we will give you the\
 location of a 
BISSELL Authorized Service Center in your area. If you have questions about your warranty 
or need replacement parts please contact the numbers below.
Or visit the BISSELL website -  www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date:  ___________________
NOTE:	Please	 keep	your	original	 sales	receipt.	 It	 
provides	 proof	of	purchase	 date	in	the	 event	 of	a	 
warranty	 claim.	See	Warranty	 on	page	 19	for	 details.		
For UK inquiries:
Monday - Thursday     9 am — 5 pm 
Friday      9 am — 4 pm 
BISSELL Homecare (Overseas)  
Ground Floor  
226 Berwick Avenue  
Slough  
Berkshire, SL1 4QT   
United Kingdom 
Telephone: 0844 888 6644 For	
all	other	 inquiries:
Monday - Friday     8 am — 4 pm 
BISSELL	 Homecare,	 Inc.
PO Box 1888
Grand Rapids, Michigan 49501 USA
Telephone: 01 616 453 4451  
Fax: 01 616 453 1383