BenQ Xl2411z User Manual

  11   How to assemble your monitor hardware
4. Connect the power cable to the monitor.
Plug one end of the power cord into the socket 
labelled   on the rear of the monitor. Do not 
connect the other end to a power outlet just yet. 
5. Route the cables via the cable clip.
6. Connect-to and turn-on the power.
Plug the other end of the power cord into a power 
outlet and turn it on.
Picture may differ from product supplied for your region.
Turn on the monitor by pressing the power button 
on the monitor....

12  How to assemble your monitor hardware  
How to detach the stand base
1. Prepare the monitor and area.
Turn off the monitor and the power before 
unplugging the power cable. Turn off the computer 
before unplugging the monitor signal cable.
Protect the monitor and screen by clearing a flat 
open area on your desk and placing a soft item like 
a towel on the desk for padding, before laying the 
screen face down on a flat clean padded surface.
Please be careful to prevent damage to the monitor. Placing...

  13   How to assemble your monitor hardware
Adjusting the monitor height
To extend the monitor stand to a higher position, press 
the lower part of the height release on the stand while 
holding the bottom of the monitor at the same time. 
And pull the stand and the monitor upward together 
to the desired height.
If the height release in the proceeding operation cannot be 
pressed down, press the top of the monitor once as 
illustrated on the right before you proceed.
If you prefer to lower the monitor...

14  How to assemble your monitor hardware  
• Avoid placing hands on the upper or lower part of the 
height-adjustable stand or at the bottom of the 
monitor, as ascending or descending monitor might 
cause personal injuries. Keep children out of reach of 
the monitor while performing this operation.
• If the monitor has been rotated to portrait mode and height adjustment is desired, you should 
be noted that the wide screen will keep the monitor from being lowered to its minimum 
height.
 

  15   How to assemble your monitor hardware
Rotating the monitor
1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 
degrees.
Click to launch the 
Display Pilot Software (if installed from the CD), and check Auto Pivot to 
set the display to rotate with the monitor automatically.
Alternatively, right-click the desktop and select 
Screen resolution from the popup menu. Select 
Portrait in Orientation, and apply the setting.
Depending on...

16  How to assemble your monitor hardware  
Viewing angle adjustment
You may position the screen to the desired angle with -5° to + 20° monitor tilt, 90° (left and 
right total) monitor swivel, and 130 mm monitor height.
4. Adjust the monitor to the desired viewing 
angle.
-5O~ +20O
-45O ~ +45O-45O ~ +45O
130 mm
 

  17   How to assemble your monitor hardware
Using the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the 
installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, 
please read the precautions carefully.
Precautions
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power...

18  Getting the most from your BenQ monitor  
Getting the most from your BenQ monitor
To gain the most benefit from your new BenQ color LCD flat screen monitor, you should install 
the custom BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor 
CD-ROM.
The circumstances under which you connect and install your BenQ LCD Monitor will 
determine which process you need to follow to successfully install the BenQ LCD Monitor 
driver software. These circumstances relate to which version of...

  19   Getting the most from your BenQ monitor
How to install the monitor on a new computer
This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver 
software on a new computer which has never had a monitor driver installed before. This 
instruction is only suitable for a computer which has never been used before, and for which the 
BenQ LCD Monitor is the first ever monitor to be connected to it.
1.  Follow the instructions in How to assemble your monitor hardware...

20  Getting the most from your BenQ monitor  
How to upgrade the monitor on an existing computer
This instruction details the procedure for manually updating the existing monitor driver 
software on your Microsoft Windows computer. It is currently tested as compatible for 
Windows 8 and Windows 7 Operating System (OS). 
Installing monitor driver software involves selecting an appropriate information file (.inf) on the 
BenQ LCD Monitor CD-ROM for the particular model monitor you have connected, and...