BenQ Xl2411z User Manual

							  11   How to assemble your monitor hardware
4. Connect the power cable to the monitor.
Plug one end of the power cord into the socket 
labelled   on the rear of the monitor. Do not 
connect the other end to a power outlet just yet. 
5. Route the cables via the cable clip.
6. Connect-to and turn-on the power.
Plug the other end of the power cord into a power 
outlet and turn it on.
Picture may differ from product supplied for your region.
Turn on the monitor by pressing the power button 
on the monitor. 
Turn on the computer too, and follow the 
instructions in Getting the most from your BenQ 
monitor on page 18 to install the monitor 
software.
To extend the service life of the product, we recommend 
that you use your computers power management function.
 
						

							12  How to assemble your monitor hardware  
How to detach the stand base
1. Prepare the monitor and area.
Turn off the monitor and the power before 
unplugging the power cable. Turn off the computer 
before unplugging the monitor signal cable.
Protect the monitor and screen by clearing a flat 
open area on your desk and placing a soft item like 
a towel on the desk for padding, before laying the 
screen face down on a flat clean padded surface.
Please be careful to prevent damage to the monitor. Placing 
the screen surface on an object like a stapler or a mouse will 
crack the glass or damage the LCD substrate voiding your 
warranty. Sliding or scraping the monitor around on your 
desk will scratch or damage the monitor surround and 
controls. 
2. Release the thumbscrew on the bottom of 
the monitor base and detach the monitor 
base as illustrated.
1
2
 
						

							  13   How to assemble your monitor hardware
Adjusting the monitor height
To extend the monitor stand to a higher position, press 
the lower part of the height release on the stand while 
holding the bottom of the monitor at the same time. 
And pull the stand and the monitor upward together 
to the desired height.
If the height release in the proceeding operation cannot be 
pressed down, press the top of the monitor once as 
illustrated on the right before you proceed.
If you prefer to lower the monitor stand height, push 
the stand downward while holding both left and right 
sides of the monitor. 
Height release
 
						

							14  How to assemble your monitor hardware  
• Avoid placing hands on the upper or lower part of the 
height-adjustable stand or at the bottom of the 
monitor, as ascending or descending monitor might 
cause personal injuries. Keep children out of reach of 
the monitor while performing this operation.
• If the monitor has been rotated to portrait mode and height adjustment is desired, you should 
be noted that the wide screen will keep the monitor from being lowered to its minimum 
height.
 
						

							  15   How to assemble your monitor hardware
Rotating the monitor
1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 
degrees.
Click to launch the 
Display Pilot Software (if installed from the CD), and check Auto Pivot to 
set the display to rotate with the monitor automatically.
Alternatively, right-click the desktop and select 
Screen resolution from the popup menu. Select 
Portrait in Orientation, and apply the setting.
Depending on the operating system on your PC, different procedures should be followed to adjust the screen 
orientation. Refer to the help document of your operating system for details.
2. Fully extend the monitor and tilt it.
Gently lift the display up and extend the stand to the 
maximum extended position. Then tilt the monitor.
The monitor should be vertically extended to allow to rotate 
from landscape to portrait mode.
3. Rotate the monitor 90 degrees clockwise as 
illustrated.
To avoid the edge of the LCD display hitting the monitor base 
surface while it is being rotated, do tilt and extend the monitor 
to the highest position before you start to rotate the display. You 
should also make sure there are no obstacles around the monitor 
and there is enough room for cables.
90
 
						

							16  How to assemble your monitor hardware  
Viewing angle adjustment
You may position the screen to the desired angle with -5° to + 20° monitor tilt, 90° (left and 
right total) monitor swivel, and 130 mm monitor height.
4. Adjust the monitor to the desired viewing 
angle.
-5O~ +20O
-45O ~ +45O-45O ~ +45O
130 mm
 
						

							  17   How to assemble your monitor hardware
Using the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the 
installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, 
please read the precautions carefully.
Precautions
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power before disconnecting the cables from the LCD monitor.
1. Remove the monitor stand.
Lay the screen face down on a clean and 
well-padded surface. Detach the monitor base as 
instructed in How to detach the stand base on page 
12.
2. Remove the monitor stand.
Use a a cross-pointed screwdriver to release the 
screws that fixing the monitor stand to the 
monitor. The use of a magnetic-head screwdriver is 
recommended to avoid of losing the screws.
Then pull the monitor stand backward away from 
the monitor.
In case you intend to use your monitor on the stand in the 
future, please keep the monitor base, monitor stand, and 
screws somewhere safe for future use.
3. Follow the instruction manuals of the wall 
mount bracket you purchased to complete 
the installation.
 
						

							18  Getting the most from your BenQ monitor  
Getting the most from your BenQ monitor
To gain the most benefit from your new BenQ color LCD flat screen monitor, you should install 
the custom BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor 
CD-ROM.
The circumstances under which you connect and install your BenQ LCD Monitor will 
determine which process you need to follow to successfully install the BenQ LCD Monitor 
driver software. These circumstances relate to which version of Microsoft Windows you are 
using, and whether you are connecting the monitor and installing the software onto a new 
computer (without existing monitor driver software), or whether you are upgrading an existing 
installation (which already has existing monitor driver software) with a newer monitor.
In either case however, the very next time you turn on your computer (after connecting the 
monitor to your computer), Windows will automatically recognize the new (or different) 
hardware, and will launch its 
Found New Hardware wizard.
Follow the wizard instructions until it asks you to select a monitor model. At that point, click 
the 
Have Disk button, insert the BenQ LCD Monitor CD-ROM and select the appropriate 
monitor model. Further details and step-by-step instructions for either an automatic (new) or 
upgrade (existing) installation, see:
• How to install the monitor on a new computer on page 19.
• How to upgrade the monitor on an existing computer on page 20.
• If you require a User Name and Password to login to your Windows computer, you must be logged on as an 
Administrator or as a member of the Administrators group in order to install the monitor driver software. 
Furthermore, if your computer is connected to a network which has security access requirements, network 
policy settings may prevent you from installing software on your computer.
• To check the name of the purchased model, refer to the specification label on the back of the monitor.
 
						

							  19   Getting the most from your BenQ monitor
How to install the monitor on a new computer
This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver 
software on a new computer which has never had a monitor driver installed before. This 
instruction is only suitable for a computer which has never been used before, and for which the 
BenQ LCD Monitor is the first ever monitor to be connected to it.
1.  Follow the instructions in How to assemble your monitor hardware on page 8. 
When Windows starts, it will automatically detect the new monitor and launch the 
Found 
New Hardware Wizard
. Follow the prompts until it displays the option to Install 
Hardware Device Drivers
.
2.  Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
3.  Check 
Search for a suitable driver for my device option, and click Next.
4.  Check the option for CD-ROM drives (uncheck all others) and click 
Next.
5.  Look to confirm that the wizard has selected the correct name of your monitor and click 
Next.
6.  Click 
Finish.
7.  Restart the computer.
If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor 
connected to it (and has monitor driver software installed), you should not be following these instructions. You 
should instead be following the instructions for How to upgrade the monitor on an existing computer.
To find the suitable driver files for the purchased model, refer to the following table.
Driver filesSuitable models
XL2411T XL2411T / XL2411TE
XL2411Z XL2411Z / XL2411ZE
 
						

							20  Getting the most from your BenQ monitor  
How to upgrade the monitor on an existing computer
This instruction details the procedure for manually updating the existing monitor driver 
software on your Microsoft Windows computer. It is currently tested as compatible for 
Windows 8 and Windows 7 Operating System (OS). 
Installing monitor driver software involves selecting an appropriate information file (.inf) on the 
BenQ LCD Monitor CD-ROM for the particular model monitor you have connected, and 
letting Windows install the corresponding driver files from the CD. You need only steer it in the 
right direction. Windows has an Upgrade Device Driver Wizard to automate the task and guide 
you through the file selection and installation process. 
See:
• How to install on Windows 8 system on page 21.
• How to install on Windows 7 system on page 22.
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows, 
however, as at the time of writing, BenQ has done no testing of this driver on other versions of Windows and 
cannot guarantee its operation on those systems.