BenQ W6000/W6500 Digital Projector Home Cinema Series User Manual

  41
  Using the projector
English
Advanced Setup menu
Background Color
( Blue )
Allows you to choose the color of the background screen that will be displayed 
when there is no input source detected.
Menu Settings
Menu Display Time (10 sec)
Sets the length of time the OSD will remain active after your last key press. The 
range is from 5 to 30 seconds in 5-second increments.
Menu Position (Center)
Sets the On-Screen Display (OSD) menu position.
Input SourceSelects an input source to be projected. See...

42 Using the projector  
English
Information menu
This menu shows you the current operating status of the projector.
Some picture adjustments are available only when certain input sources are in use. Unavailable 
adjustments are not shown on the screen.
Reset All Settings
Returns all settings to the factory preset values.
The following settings will still remain: names of user modes, 
Keystone, Language, Projector Position, High Altitude Mode, 
Password, Key Lock, and ISF.
ISF
The ISF calibration menu...

  43
  Additional information
English
Additional information
Care of the projector
Your projector needs little maintenance. The only thing  you have to do on a regular basis is keep the lens 
clean. Never remove any parts of the projector except  the lamp. Contact your dealer or local customer 
service center if the projector fails to operate as expected.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface. Before you attempt to clean the lens, turn 
the projector off,...

44 Additional information  
EnglishLamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage 
is automatically calculated by the 
built-in timer. The method of 
calculating the equivalent lamp hour is as follows:
Equivalent lamp hour 
= 1 (hours used in  Economic mode) + 3/2 (hours used in  Normal mode)
See Setting Lamp Power as Economic  below for more information on 
Economic mode.
To obtain the lamp hour information:
1. Press  MENU and...

  45
  Additional information
EnglishTiming of replacing the lamp
When the Lamp indicator lights up red or a message  appears suggesting it is time to replace the lamp, 
please install a new lamp or consult your dealer. An  old lamp may cause a malfunction in the projector and 
in some instances the la mp may explode. Go to  http://lamp.BenQ.com for a replacement lamp.
The Lamp indicator light and Temperature warning light  will light up if the lamp becomes too hot. Turn 
the power off and let the...

46 Additional information  
English1. Turn the power off and disconnect the 
projector from the power outlet. Turn off all 
connected equipment and disconnect all other 
cables. See  Turning the projector off  on 
page 36  for details.
2. Slightly lift the projector up. Loosen the screws  on the lamp cover (located on the left side).
3. Remove the lamp cover. 
4. Loosen the screws that hold the lamp to the  projector. If the screws are not loosened 
completely, they could injure your fingers.
5. Lift...

  47
  Additional information
EnglishResetting the lamp timer
Do not reset the lamp timer if the lamp has not been replaced as this could cause damage.
1. After the start-up logo, press  MENU and then press  /  until the 
Advanced Setup  menu is highlighted.
2. Press  to highlight  Lamp Settings and press ENTER. The Lamp 
Settings  page displays.
3. Highlight  Reset Lamp Timer  and press ENTER. A warning message 
displays asking if you want to reset the lamp timer. Highlight  Reset 
and press  ENTER....

48 Additional information  
EnglishIndicators
There are three indicators which show the status of 
the projector. Check the following for information 
about the indicator lights. If there is anything wron g, turn the projector off and contact your dealer.
 When the projector is in a normal state
 When the projector is in an abnormal state
PowerTe m pLampStatus & Description
Orange Off OffStand-by mode
Green
Flashing Off OffPowering up
Green Off OffNormal operation
Orange
Flashing Off Off
•  The...

  49
  Additional information
EnglishTroubleshooting
ProblemCauseRemedy
The projector does not 
turn on. There is no power from the power 
cable.
Plug the power cable into the AC inlet on the 
rear of the projector, and plug the power cable 
into to the power outlet. If the power outlet 
has a switch, make sure that it is switched on. 
(See page 20.)
Attempting to turn the projector on 
again during the cooling process. Wait until the cooling down process has 
completed.
The lamp cover is not securely...

50 Additional information  
EnglishSpecifications
All specifications are subject to change without notice. 
 Optical
Projection system
Single-chip DLPTM system.
DMD chip 0.65 DLP (1920 x 1080)
Lens F = 2.48 to 2.83, f = 24.1 to 36.14 mm
Projection screen size 28 to 300
Lamp 280W
 Electrical
CompatibilityPC: 640 x 400 to 1920  x 1200
Video: NTSC, PAL, SECAM, YPbPr (480i/480p/576i/576p), HDTV 
(720p/1080i/1080p)
DDC 2B
Color Space Typ. = 70% NTSC (Target Color Gamut = HDTV Rec. 709)
 Terminals
InputAnalog...