BenQ W6000/W6500 Digital Projector Home Cinema Series User Manual

  21
  Using the projector
EnglishSelecting an input source
The projector can be connected to multiple equipment at the same time. 
When the projector is first turned on, it will attempt to reconnect with the 
input source which was in use when the projector was last shut down.
To  s e l e c t  t h e  v i d e o  s o u r c e :
•  Using the remote control or projector
Press one of the Source keys on the remote control, or press  SOURCE on 
the projector repeatedly until your desired signal is selected.
•...

22 Using the projector  
EnglishUsing the menus
The projector is equipped with multilingual On
-Screen Display (OSD) menus for making various 
adjustments and settings.
Below is the overview of the OSD menu.
To use the OSD menus, please set the OSD menu to your familiar language.
Securing the projector
Using a security cable lock
The projector has to be installed in a safe place to pr event theft. Otherwise, purchase a lock, such as the 
Kensington lock, to secure the projector. You can locate  a...

  23
  Using the projector
EnglishUtilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option for setting up 
password security. The password can be set throug h the On-Screen Display (OSD) menu. Once the 
password is set and this function is selected, the pr ojector is password-protected. Users who do not know 
the correct password can not use the projector.
You will be inconvenienced if you activate the password functionality and...

24 Using the projector  
EnglishEntering the password recall procedure
1. Make sure the 
Input Password page displays on screen. Press and hold 
PRESET MODE  on the projector or remote control for 3 seconds. The 
projector will display a coded number on the screen.
2. Write down the number and turn off your projector.
3. Seek help from the local BenQ service center to decode the number.  You may be required to provide proof of purchase documentation to 
verify that you are an authorized user of the...

  25
  Using the projector
EnglishAdjusting the projected image
Adjusting the projection angle 
There are four adjuster feet on the bottom of the projector. These can be 
used if necessary to change the projecti on angle. Screw the feet in or out as 
appropriate to aim and level the projection angle.
If the screen and the projector are not perpendicular to each other, the projected image becomes vertical 
trapezoidal. To correct this problem, see  Correcting picture distortion on page 25  for details....

26 Using the projector  
EnglishUsing the preset and user modes
Selecting a preset mode
The projector is preset with several pre-defined picture modes so that you can choose one to suit your 
operating environment and input source picture type.
To select a picture mode that suits your need:
•  Using the remote control
1. Press 
PRESET MODE  repeatedly or USER 1, USER 2/ISF NIGHT , 
USER 3/ISF DAY , DEFAULT  on the remote control, or  PRESET 
MODE  on the projector repeatedly until your desired mode is...

  27
  Using the projector
EnglishSetting the User 1/User 2/User 3 mode
There are three user-definable modes if the current available picture modes are not suitable for your need. 
You can use one of the picture modes (except the selected User mode) as a starting point and customize the 
settings.
1. In the  Picture -- Basic  menu, highlight  Picture Mode and press  /  
to select  User 1, User 2 , or User 3  mode.
2. Press   to highlight  Load Settings From .
This function is only available when User 1,...

28 Using the projector  
EnglishFine-tuning the picture quality
No matter what picture mode you have selected, you are able to fine-tune those settings to fit every 
presentation purpose. Those adjustments will be saved to the preset mode you are at when you exit the 
OSD menu.
Adjusting Brightness
Highlight 
Brightness  in the Picture -- Basic  menu and adjust 
the values by pressing  /  on the projector or remote 
control.
The higher the value, the brighter the picture. And the lower 
the setting, the...

  29
  Using the projector
EnglishAdvanced picture quality controls
There are more advanced functions in the  Picture -- Advanced menu to be adjusted to your preference. To 
save the settings, just press  MENU to leave the OSD menu.
Setting Black Level
Highlight  Black Level  and press  /  on the projector or remote control 
to select  0 IRE or 7.5 IRE .
The grayscale video signal is measured  in IRE units. In some areas which 
use NTSC TV standard, the grayscale is measured from 7.5 IRE (black) to 
100...

30 Using the projector  
EnglishSetting a preferred color temperature
To set a preferred color temperature:
1. Highlight 
Color Temperature  and select User 1, User 2 , or User 3  by 
pressing  /  on the projector or remote control.
2. Press  to highlight  Color Temperature User_ Fine Tuning  and press 
ENTER . The Color Temperature User_ Fine Tuning  page displays.
The menu name User_ corresponds with the setting selected 
in Color Temperature.
3. Press  /  to highlight the item you want to change and...