BenQ Sh910 Digital Projector User Manual

Operation 61
3. 
SOURCEQuick Auto Search On/Off
Color Space ConversionAuto/RGB/YUV
4. 
SYSTEM 
SETUP: 
Basic
Language
Projector PositionFront Table/Rear Table/Rear 
Ceiling/Front Ceiling
Menu SettingsMenu display 
time5 sec/10 sec/15 sec/20 sec/25 
sec/30 sec
Menu positionCenter/Top-left/Top-right/Bottom-
right/Bottom-left
Reminder Messge On/Off
Operation 
SettingsDirect Power On On/Off
Auto Power OffDisable/5 min/10 min/15 min/20 
min/25 min/30 min
Quick Cooling On/Off
Blank TimerDisable/5 min/10 min/15...

Operation 62
5. 
SYSTEM 
SETUP: 
Advanced
High Altitude 
ModeOn/Off
Audio SettingsSRS On/Off
Mute On/Off
Volume
Microphone 
Volume
Power on/off Ring 
ToneOn/Off
Lamp SettingsLamp Mode Normal/Economic
Reset lamp timer
Equivalent lamp hour
Security 
SettingsChange password
Change Security 
SettingsPower on Lock
Web Control Lock
Baud Rate2400/4800/9600/19200/ 38400/
57600/115200
Test Pattern On/Off
Closed CaptionClosed Caption 
EnableOn/Off
Caption VersionCC1/CC2/CC3/CC4
Standby 
SettingsNetwork On/Off...

Operation 63 Note that the menu items are available when the projector detects at least one valid signal. If 
there is no equipment connected to the projector or no signal detected, limited menu items 
are accessible.
5. 
SYSTEM 
SETUP: 
AdvancedNetwork 
SettingsWired LANStatus
DHCP
IP Address
Subnet Mask
Default Gateway
DNS Server
Apply
Wireless LANStatus
SSID
IP Address
Connection Mode
DHCP
IP Address
Subnet Mask
Apply
Remote DesktopAccount
Password
Connect/Disconnect
Projection Log in 
CodeOn/Off
Mac...

Operation 64
Description of each menu
• The default values listed in this manual, especially on pages 64-72, are for reference only. 
They may vary between the projectors due to the continuous improvement to the  
products.
FUNCTIONDESCRIPTION
Wall ColorCorrects the projected picture’s color when the projection surface is 
not white. See Using Wall Color on page 32 for details.
Aspect RatioThere are four options to set the images aspect ratio depending on 
your input signal source. See Selecting the...

Operation 65
FUNCTION)DESCRIPTION
Picture ModePre-defined picture modes are provided so you can optimize your 
projector image set-up to suit your program type. See Selecting a 
picture mode on page 31 for details.
Reference 
Mode
Selects a picture mode that best suits your need for the image quality 
and further fine-tune the image based on the selections listed on the 
same page below. See Setting the User 1/User 2 mode on page 31 for 
details.
This function is only available when User 1 or User 2 is...

Operation 66
FUNCTIONDESCRIPTION
Brilliant Color
Adjusts white peaking while maintaining correct color presentation. 
See Adjusting Brilliant Color on page 32 for details.
This function is only available when User 1/2 is selected.
Color 
TemperatureSee Selecting a Color Temperature on page 32 for details.
This function is only available when User 1/2 is selected.
3D Color 
ManagementSee 3D Color Management on page 33 for details.
This function is only available when User 1/2 is selected.
Save Settings...

Operation 67
FUNCTIONDESCRIPTION
LanguageSets the language for the On-Screen Display (OSD) menus. See Using 
the menus on page 25 for details.
Projector 
PositionThe projector can be installed on a ceiling or behind a screen, or with 
one or more mirrors. See Choosing a location on page 15 for details.
Menu 
Settings
Menu display time
Sets the length of time the OSD will remain active after your last key 
press. The range is from 5 to 30 seconds in 5-second increments.
Menu position
Sets the On-Screen...

Operation 68
FUNCTIONDESCRIPTION
Remote 
ReceiverSets which IR remote sensor of the projector will receive the signal 
from the remote control.  
Background 
ColorAllows you to select which background color will display when no 
signal is input into the projector. Three options are available: Black, 
Blue, or Purple.
Splash 
Screen
Allows you to select which logo screen will display during projector 
start-up. Three options are available: BenQ logo, Black, or Blue.
4. SYSTEM SETUP: 
Basic menu 

Operation 69
FUNCTIONDESCRIPTION
High Altitude 
ModeA mode for operation in high altitude areas. See Operating in a high 
altitude environment on page 35 for details.
Audio 
Settings
Allows you to enter the audio setting menu. See Adjusting the sound 
on page 35 for details.
SRS
See Turning on/off the SRS on page 36 for details.
Mute
See Muting the sound on page 35 for details.
Volume
See Adjusting the sound level on page 35 for details.
Microphone volume
See Adjusting the microphone’s sound level on...

Operation 70
FUNCTIONDESCRIPTION
Baud RateSelects a baud rate that is identical with your computer’s so that you 
can connect the projector using a suitable RS-232 cable. This function 
is intended for qualified service personnel.
Test PatternSelecting On enables the function and the projector displays the grid 
test pattern. It helps you adjust the image size and focus and check that 
the projected image is free from distortion.
Closed 
Caption
Closed Caption Enable
Activates the function by selecting...