BenQ Projector I500 User Manual

  31
OperationsStarting up the projector1.  Plug the power cable into the projector and a power outlet. Turn on the power outlet switch (where fitted). The POWER indicator light on the 
projector lights orange after power has been applied.
2.  Connect any video equipment to the respective port on the rear of the projector. If you do not want to project video via such equipment but 
want to access the BenQ Launcher, you do not need to connect any video equipment.
3.  Press   on the projector or   on the...

32
• Use OK to confirm the selected menu item.
Step 1: 
Specify Projector Position.
The Setup Wizard screenshots below are for reference only and may differ from the actual design.For more information about projector position, see Choosing a location on page 22. 

  33
Step 2: 
Specify OSD Language.
Step 3: 
Specify Auto Keystone.
Available languages may vary by the product supplied for your region and may be updated without prior notice. 

34
Step 4: 
Specify Auto Source.
Step 5:
Specify the Network Settings (either connecting to a WLAN AP or using LAN connection).
 
You may need to enter a password if you choose to connect to a WLAN AP. 

  35
Now you’ve completed the initial setup.
5.  Switch on the connected equipment.
6.  The projector starts to search for available input signals. The current input signal being scanned displays on the screen. If the projector is unable 
to detect a valid signal, the projector will automatically open the BenQ Launcher. You may press   on your remote control to select your 
desired input signal.
7.  If the horizontal frequency of the input source exceeds the range supported by the projector, the No...

36
Shutting down the projector1.  Press   on the projector or   on your remote control. The projector displays a shutdown confirmation message. 
2.  Press   or   a second time. The POWER indicator light flashes orange and the fans run for about two minutes to cool the lamp. The 
projector does not respond to any commands during the cooling process.
3.  When the cooling process ends, the POWER indicator light will show a solid orange.
If the projector will not be used for an extended period, unplug the...

  37
Securing the projectorUsing the security barThe projector has to be installed in a safe place to prevent theft. It has a security lock bar located at the bottom of the projector which you can use to 
secure the projector via a variety of purchasable self-locking cables. Selecting an input sourceThe projector can be connected to multiple equipment at the same time. However, it only displays one full screen at a time. When starting up, the 
projector automatically searches for the available signals....

38
To select the video source:
1.  Press  on your remote control to display the source selection bar.
2.  Press  /  until your desired signal is selected and press OK.
Once detected, the selected source information displays on the screen for seconds. If there are multiple pieces of equipment connected to the 
projector, repeat steps 1-2 to search for another signal.
The native display resolution of this projector is in a 16:10 aspect ratio. For best display picture results, you should select and use an...

  39
Adjusting the projected imageAdjusting the projection angle The projector is equipped with a quick-release adjuster foot and a rear adjuster foot. These adjusters change the image height and projection angle. 
To adjust the projection angle:
• Press the quick-release button and lift the front of the projector. Once the image is positioned as desired, release the quick-release button to lock 
the foot in position.
• To retract the foot, hold up the projector while pressing the quick-release button,...

40
Fine-tuning the image clarityTo sharpen the picture, rotate the focus ring on the projector.Correcting keystoneKeystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not 
perpendicular to the screen. 
You may correct this in the following way.
• Using the OSD settings menu
• Select Key s t o n e.