BenQ Bl3200pt User Manual

  11   How to assemble your monitor hardware
Tighten the thumbscrew on the bottom of the monitor 
base as illustrated. And then turn the stand 
counterclockwise to face forward.
Orient and align the stand arm with the monitor ( ), 
push them together until they click and lock into place 
().
Gently attempt to pull them back apart to check that 
they have properly engaged.
Carefully lift the monitor, turn it over and place it 
upright on its stand on a flat even surface.
You should position the monitor...

12  How to assemble your monitor hardware  
To Connect the DVI-D Cable
Connect the plug of the DVI-D cable (at the end 
without the ferrite filter) to the monitor video socket. 
Connect the other end of the cable (at the end with the 
ferrite filter) to the computer video socket.
Tighten all finger screws to prevent the plugs from 
accidently falling out during use.
Or
To Connect the HDMI Cable
Connect the plug of the HDMI cable to the HDMI port 
on the monitor. Connect the other end of the cable to 
the...

  13   How to assemble your monitor hardware
You may connect headphones to the headphone jack 
found on the back side of the monitor.
4. Connect USB devices.
Connect the USB cable between the PC and the 
monitor (via the upstream USB port at the back). This 
upstream USB port transmits data between the PC and 
the USB devices connected to the monitor.
Connect USB devices via other USB ports 
(downstream) on the monitor. These downstream USB 
ports transmit data between connected USB devices 
and the...

14  How to assemble your monitor hardware  
5. Connect the memory card.
Insert an SD, MMC, or MS memory card following the 
direction indicated on the card to exchange files.
Requires card reader driver for Windows 8.1 operating 
system. Install the driver from the supplied CD.
Supported memory card formats are as follows:
• SD / SDHC / SDXC
• MMC
• Memory Stick / Memory Stick Pro
• MS Duo / MS-Pro Duo
6. Connect the OSD Controller to the 
monitor.
Connect the OSD Controller to the mini USB port...

  15   How to assemble your monitor hardware
8. Organize the cables.
Attach the wire holder to its socket on the rear of the 
monitor. And insert the cables one after one into the 
wire holder ( ).
Route the cables via the cable management hole ( ).
9. Connect-to and turn-on the power.
Plug the other end of the power cord into a power 
outlet and turn it on.
Picture may differ from product supplied for your region.
Switch the power switch next to the AC power input 
jack to ON.
Turn on the monitor by...

16  How to assemble your monitor hardware  
How to detach the stand and the base
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging 
the power cable. Turn off the computer before 
unplugging the monitor signal cable.
Protect the monitor and screen by clearing a flat open 
area on your desk and placing a soft item like a towel on 
the desk for padding, before laying the screen face down 
on a flat clean padded surface.
Please be careful to prevent damage to the monitor....

  17   How to assemble your monitor hardware
Turn the stand counterclockwise until you cannot go 
further.
And then detach the base from the stand.
 

18  How to assemble your monitor hardware  
Adjusting the monitor height
To adjust the monitor height, hold both the left and the 
right sides of the monitor to lower the monitor or lift 
it up to the desired height.
• Avoid placing hands on the upper or lower part of the 
height-adjustable stand or at the bottom of the monitor, as 
ascending or descending monitor might cause personal 
injuries. Keep children out of reach of the monitor while 
performing this operation.
• If the monitor has been rotated...

  19   How to assemble your monitor hardware
Rotating the monitor
1. Pivot the display.
Before rotating the monitor with a portrait viewing orientation, the display has to be rotated 90 
degrees.
a. Go to 
Display and Auto Pivot. Select On.
b. Click to launch the 
Display Pilot Software (if installed from the CD), and check Auto Pivot 
to set the display to rotate with the monitor automatically.
Alternatively, right-click the desktop and select 
Screen resolution from the popup menu. 
Select 
Portrait in...

20  How to assemble your monitor hardware  
Viewing angle adjustment
You may position the screen to the desired angle with -5° to + 20° monitor tilt, 90° (left and 
right total) monitor swivel, and 150 mm monitor height.
4. Adjust the monitor to the desired viewing 
angle.
-5-5O O
 ~ +20~ +20O-5O ~ +20O-45-45O O ~ +45~ +45O-45O ~ +45O
150 mm