BEKO WML 15105 D User Manual

							
WML 15105 D
WML 15085 D
WML 15065 D
Washing Machine
Veïas mazgâjamâ mašîna
Plně automatická pračka
Automatická pračka
 
						

							
2 - EN
1 Warnings
General Safety•  Never place your machine on a carpet covered floor. Otherwise, 
lack of airflow from below of your 
machine may cause electrical parts to 
overheat. This may cause problems 
with your washing machine.
•  If the power cable or mains plug is 
damaged you must call Authorized 
Service for repair.
•  Fit the drain hose into the discharge  housing securely to prevent any 
water leakage and to allow machine to take in and discharge water as 
required. It is very important that the 
water intake and drain hoses are not 
folded, squeezed, or broken when 
the appliance is pushed into place after it is installed or cleaned.
•   Your washing machine is designed 
to continue operating in the event of 
a power interruption. Your machine 
will not resume its program when 
the power restores. Press the 
“Start/Pause/Cancel” button for 3 
seconds to cancel the program (See, 
Canceling a Program)
•   There may be some water in your  machine when you receive it. This is 
from the quality control process and 
is normal. It is not harmful to your machine.
•  Some problems you may encounter  may be caused by the infrastructure. 
Press "Start/Pause/Cancel" button 
for 3 seconds to cancel the program 
set in your machine before calling the 
authorized service.
First Use•   Carry out your first washing process without loading your machine and with detergent under “Cottons 90°C” 
program.
•  Ensure that the cold and hot water  connections are made correctly when 
installing your machine.
•  If the current fuse or circuit breaker is  less than 16 Amperes, please have 
a qualified electrician install a 16 
Ampere fuse or circuit breaker.
•  While using with or without a  transformer, do not neglect to have 
the grounding installation laid by a 
qualified electrician. Our company shall not be liable for any damages that may arise when the machine is 
used on a line without grounding.
•  Keep the packaging materials out  of reach of children or dispose them  by classifying according to waste 
directives.
Intended use•  This product has been designed for home use.
•   The appliance may only be used for 
washing and rinsing of textiles that 
are marked accordingly.
Safety instructions•   This appliance must be connected to  an earthed outlet protected by a fuse 
of suitable capacity.
•   The supply and draining hoses must  always be securely fastened and 
remain in an undamaged state.
•  Fit the draining hose to a washbasin  or bathtub securely before starting up 
your machine. There may be a risk of 
being scalded due to high washing 
temperatures!
•  Never open the loading door or  remove the filter while there is still 
water in the drum.
•   Unplug the machine when it is not in 
use.
•  Never wash down the appliance with  a water hose! There is the risk of 
electric shock!
•   Never touch the plug with wet hands. 
Do not operate the machine if the 
power cord or plug is damaged.
•   For malfunctions that cannot be 
solved by information in the operating manual:
•  Turn off the machine, unplug it,  turn off the water tap and contact 
an authorized service agent. You 
may refer to your local agent or 
solid waste collection center in your 
municipality to learn how to dispose 
of your machine.  
If there are children in your 
house...•   Keep children away from the machine when it is operating. Do not let them tamper with the machine.
•   Close the loading door when you  leave the area where the machine is 
located.
 
						

							
3 - EN
2 Installation
Removing packaging 
reinforcement
Tilt the machine to remove the packaging 
reinforcement. Remove the packaging 
reinforcement by pulling the ribbon.
Opening the transportation locksA  Transportation safety bolts must be removed before operating the 
washing machine! Otherwise, the machine will be damaged!
1.  Loosen all the bolts with a spanner  until they rotate freely (“C”)
2.  Remove transportation safety bolts  by turning them gently.
3.  Fit the covers (supplied in the bag 
with the Operation Manual) into the 
holes on the rear panel. (“P”)
C Keep the transportation safety bolts 
in a safe place to reuse when the 
washing machine needs to be moved 
again in the future.
C Never move the appliance without the transportation safety bolts 
properly fixed in place!
Adjusting the feetA  Do not use any tools to loosen the lock nuts. Otherwise, they can be damaged.
1.  Manually (by hand) loosen the lock 
nuts on the feet.
2.  Adjust them until the machine stands  level and firmly.
3.  Important: Tighten all lock nuts up 
again.
Connecting to the water supply.Important:
•   The water supply pressure required 
to run the machine must be 1-10 bar (0,1 – 1 MPa).
•   Connect the special hoses supplied 
with the machine to the water intake valves on the machine. 
•  In order to prevent water leakage that 
may occur at the connection points,  there are rubber seals (4 seals for the 
models with double water inlet and 2 seals for other models) attached to the hoses. These seals should be used at the tap and machine connection ends of the hoses. The plain end of the hose fitted with a filter must be attached to the tap and the elbowed end must be attached 
to the machine. Tighten the nuts of 
the hose well by hand; never use 
wrenches to tighten the nuts.
•  Models with a single water inlet 
should not be connected to the hot water tap.
When returning the appliance to its place 
after maintenance or cleaning, care should 
be taken not to fold, squeeze or block the hoses.
Connecting to the drainThe water discharge hose can be attached to the edge of a washbasin or bathtub. The drain hose should be firmly fitted into the drain as to not get out of its housing.
Important:
•   The end of the drain hose must be  directly connected to the wastewater 
drain or to the washbasin.
•   The hose should be attached to a 
height of at least 40 cm, and 100 cm at most.
•   In case the hose is elevated after 
laying it on the floor level or close 
to the ground (less than 40 cm 
above the ground), water discharge 
becomes more difficult and the 
laundry may come out wet.
•   The hose should be pushed into the  drainage for more than 15 cm. If it is 
too long you may have it shortened.
 
						

							
4 - EN
•  The maximum length of the combined hoses must not be longer than 3.2 m.
Electrical connectionConnect the machine to an earthed outlet 
protected by a fuse of suitable capacity.
Important:
•   Connection should comply with national regulations.
•   The voltage and the allowed fuse  protection are specified in the section 
“Technical Specifications”.
•   The specified voltage must be equal 
to your mains voltage.
•   Connection via extension cords or 
multi-plugs should not be made.B  A damaged power cable must be  replaced by a qualified electrician.
B  The appliance must not be operated unless it is repaired! There is the risk 
of electric shock!
3 Initial preparations for 
washing
Preparing clothes for washingLaundry items with metal attachments such as, bras, belt buckles and metal buttons will damage the machine. Remove metal attachments or place the items in a clothing 
bag, pillow case, or something similar.
•  Sort the laundry according to type  of fabric, color, and degree of soiling 
and permissible water temperature. 
Always follow the advice on the garment labels.
•   Place small items like infants’ socks 
and nylon stockings, etc. in a laundry 
bag, pillow case or something similar. 
This will also save your laundry from 
getting lost.
•   Wash “machine washable” or “hand  washable” labeled products only with 
an appropriate program.
•   Do not wash colors and whites 
together. New, dark colored cottons 
may release a lot of dye. Wash them 
separately.
•   Use only dyes/color changers and  lime removers suitable for machine 
wash. Always follow the instructions on the packaging.
•   Wash trousers and delicate clothes  turned inside out.
Correct load capacityC Please follow the information in the “Program Selection Table”. Washing 
results will degrade when the 
machine is overloaded.
Loading doorThe door locks during program operation 
and the Door Locked Symbol (Figure 3-13i) 
lights up. The door can be opened when the symbol fades out.
Detergents and softenersDetergent DrawerThe detergent drawer is composed of three compartments:
The detergent dispenser may be in two 
different types according to the model of 
your machine.
– (I) for prewash
– (II) for main wash
- (III) siphon 
– () for softener
Detergent, softener and other cleaning agentsAdd detergent and softener before starting 
the washing program.
Never open the detergent dispenser drawer 
while the washing program is running!
When using a program without pre-wash, 
no detergent should be put into the pre-
wash compartment (Compartment no. I).
Detergent quantityThe amount of washing detergent to be 
used depends on the amount of laundry, the 
degree of soiling and water hardness.
•   Do not use amounts exceeding  the quantities recommended on 
the package to avoid problems of 
excessive foam, poor rinsing, financial 
savings and finally, environmental 
protection.
•   Never exceed the (> max 
						

							
5 - EN
4  Selecting a program and operating your machine
Control panel
1 -  Spin Speed Adjustment Knob *
2 -  Temperature Adjustment Button *
3 -  Start/Pause/Cancel Button
4 -  Auxiliary Function Keys
5 -  Program Selection Knob6 -  On/Off Button
7 -  Program Follow-up Indicators
8 -  Child-proof Lock Indicator *
* According to your machine’s model
Turning the machine onYou can prepare the machine for program 
selection by pressing the “On/Off” button. 
When the “On/Off” button is pressed, the 
“Ready” light illuminates indicating that the 
door is ulocked. Press the “On/Off” button 
again to shut down the machine.
Program selectionSelect the appropriate program from the 
program table and the following washing 
temperature table according to type, 
amount and degree of soiling of the laundry. 
Select the desired program with the 
program selection button.
C Each of these programs consist of a 
complete washing process, including 
wash, rinse and, if required, spin 
cycles.
90˚C Normally soiled, white cottons and linens.
60˚C  Normally soiled, fade proof 
colored linens, cottons or synthetic clothes and lightly soiled white linens 
40˚C-30°C- Cold  
Blended clothes including synthetics and woolens as well as delicate clothes.
C Programs are limited with the highest 
spin speed appropriate for that 
particular type of cloth.
Main programs Depending on the type of textile, the 
following main programs are available:
•CottonsYou can wash your durable clothes with 
this program. Your laundry will be washed 
with vigorous washing movements during a 
longer washing cycle.
•SyntheticsYou can wash your less durable clothes on 
this program. Gentler washing movements 
and a shorter washing cycle is used 
90°
60°
40
°
30° 60°
40°
40°
30°30°Reset
3’’
1000500
7
345
6
 
						

							
6 - EN
compared to the “Cottons” program. It is 
recommended for your synthetic clothes 
(such as shirts, blouses, synthetic/cotton blended garments, etc.). For curtains and 
lace, the “Synthetic 40” program with pre-
wash and anti-creasing functions selected is 
recommended.
•DelicatesYou can wash your delicate clothes 
on this program. It has more sensitive 
washing movements and does not make 
intermediate spinning compared to 
“Synthetic” program.
•WoolensYou can wash your machine-washable 
woolen garments on this program. Wash 
by selecting the proper temperature 
according to the labels of your clothes. 
It is recommended to use appropriate 
detergents for woolens. 
•Hand WashYou can wash your woolen/delicate clothes that bear “not machine- washable” labels 
for which hand wash is recommended on 
this program. It washes the laundry with 
very tender washing movements without damaging your clothes.
Additional programs For special cases, there are also extra 
programs available:
C Additional programs may differ according to the model of your 
machine.• Super This program washes for a longer period 
at 40°C and gives the same result as the 
"Cottons 60°C" program, thus it saves 
energy. It is suitable for clothes for which 
you cannot use the "Cotton 60°C" program. 
• MiniThis program is used to quickly wash (30 minutes) a small amount of lightly soiled cotton garments.
Special programsFor specific applications, you can select any 
of the following programs:
• RinseThis program is used when you want to 
rinse or starch separately.
• Pump + SpinThis program spins with maximum possible rpm in the default setting after the water 
drains from the machine.
C You should use a lower spin speed for delicate laundries.
Spin Speed selectionYou can have your clothes spun at the maximum rpm selection on your machine by using the selection knob in models equipped with an rpm selection knob. In 
order to protect your clothes, your machine 
will not spin above 800 rpm on synthetic 
programs and 600 rpm on woolens 
program. Furthermore, if you want to skip 
the spin cycle and take your clothes out, 
turn the rpm selection knob to “no spin” 
position. 
In machines not equipped with a spin speed selection knob, the machine will spin in the maximum possible rpm in the default setting 
of the selected program.
 
						

							
7 - EN
Program selection and consumption table
• : Selectable
* : Automatically selected, not cancellable.
**: Energy Label programme (EN 60456)
Water and power consumption and programme duration may differ from the table 
shown, subject to changes in water pressure, water hardness and temperature, ambient 
temperature, type and amount of laundry, selection of auxiliary functions, and fluctuations in 
the supply voltage.
C The auxiliary functions in the table may differ according to the model of your machine.
 Programme
Max. Load (kg)
Programme Duration (~min)
Water Consumption (l)Energy Consumption (kWh)
PrewashRinse PlusRinse Hold
Spin speed reductionNo SpinNo Heat
 Cottons905133451.65••••••
 Cottons60**5140450.95••••••
 Cottons405142450.69••••••
 Super405182450.78•••
 Synthetics602.5113520.92••••••
 Synthetics402.5104520.56••••••
 Synthetics302.595520.30••••••
 Delicate30277450.36•••••
 Woollens
401.570450.36•••••
 Hand wash30145320.21•••
 Mini302.530430.17•••
 
						

							
8 - EN
Auxiliary functionsAuxiliary function selection keysSelect the required auxiliary functions before 
starting the program.
C Auxiliary function buttons may differ according to the model of your 
machine.
Auxiliary function selectionIf an auxiliary function that should not be 
selected together with a previously selected 
function is chosen, the first selected function will be cancelled and the last 
auxiliary function selection will remain active.
For example: If you want to select pre-wash 
first and then quick wash, pre-wash will be 
cancelled and quick wash will remain active.
Auxiliary function that is not compatible 
with the program cannot be selected. (see 
“Program Selection Table”)
Pre-washA pre-wash is only worthwhile for heavily 
soiled laundry. Without pre-wash you save 
energy, water, detergent and time. Pre-
wash without detergent is recommended for 
lace and curtains.
Rinse PlusWith this function, you can increase the 
number of current rinsing steps. Thus, 
sensitive skins’ risk of being affected by the 
remainder detergent on the clothes will be 
decreased.
Rinse holdIf you do not want to unload your clothes immediately after the cotton, synthetics, 
woolen and delicate fabrics program, you 
may release your clothes inside the machine 
in the last rinsing water by pressing the rinse 
hold button in order to prevent your clothes 
become wrinkled. After this process you 
may spin your laundry by pressing “Start/
Pause/Cancel” button or you may end the 
program by pressing “Start/Pause/Cancel” 
button for 3 sec.
•  In the machines equipped with spin 
speed selection knob or button, you 
can spin by selecting the desired 
spin speed and press "Start/Pause/
Cancel" button.
•  As for machines not equipped with a 
spin speed selection knob, you can 
end the program without a spin cycle 
by pressing the “Start/Pause/Cancel” 
button and draining the water. If you 
wish your clothes be spun, you can spin them by selecting “pump+spin” 
program. 
Reducing SpeedYou may use the speed reduction button whenever you wish to spin your clothes below the maximum spin speed. When 
speed reduction button is pressed, spin 
speed will be at the minimum rpm given on the panel.
No spinYou may use this program if you do not want to spin your clothes at the end of cottons, synthetics, woolen or delicate 
programs.
Cold WashingIf you wish to wash your clothes in cold 
water, you can use this program.
Starting the ProgramPress “Start/Pause/Cancel” button to start 
the program.  “Start/Pause/Cancel” button 
will light up to indicate that the program has 
started. The door is locked and the “Lid” light fades.
Progressing a programProgress of a running program is shown 
through the program follow-up indicator. At 
the beginning of every program step, the 
relevant indicator lamp will light up and light 
of the completed step will turn off. 
C If the machine is not spinning, the  program may be in rinse hold mode 
or the automatic spin correction 
system has been activated because of excessive unbalanced distribution of laundry in the machine.
Changing the selections after the 
program has started
You can use this feature after your machine 
has started to wash different textile groups 
in the same batch of clothes under higher 
or lower temperatures. You must cancel 
the ongoing program in order to change the 
washing program.
For example, press and hold the “Start/
Pause/Cancel” button for 3 seconds to 
“Cancel” the program in order to select 
“Cottons 40” program instead of “Cottons 
60” program. Select the “Cottons 40” 
program by rotating the program knob. 
Press "Start/Pause/Cancel" button to start 
the program.
Switching the machine to standby 
modePress “Start/Pause/Cancel” button momentarily to switch your machine to the standby mode. Auxiliary functions can be 
 
						

							
9 - EN
cancelled or selected in accordance with 
the step the program is at. The door can be 
opened if the water level is suitable. Laundry may be added / taken out by opening the 
door.
Child-proof lockYou can protect the appliance from being 
tampered by children by means of the child-
proof lock. In this case, no change can be 
made in the running program.
The machine is switched to child-lock by 
pressing the 1st and 2nd auxiliary functions 
from the left for 3 sec. 1st auxiliary function 
light will flash continuously. To deactivate 
the child-proof lock, press the same buttons 
for 3 sec.
Ending the program through 
cancelingIn order to cancel the selected program, 
press the "Start/Pause/Cancel" button for 3 
seconds. The machine starts to discharge 
the water. “Wash” and “Program Finished” 
lights will light up. "Start/Pause/Cancel" and 
“Wash” lights will go off after discharging 
process is over and the “Lid” light will start 
flashing. “Lid” lamp will light up continuously when the door is unlocked. 
If the program is cancelled in the middle 
of the process, “Wash” and “Program 
Finished” lights will light up. The machine can drain all the water or can take in water for 3 times at most to cool down the clothes 
and complete draining process. When the 
water discharging process is completed, 
the “Wash” light will go off, the “Program 
Finished” light will light up and the “Lid” light will continuously flash until the door is unlocked.
End of programThe “Program Finished” lamp on the 
program follow-up indicator will light up 
when the program comes to an end. The lid 
is unlocked 2 minutes later, the “Program 
Finished” and “Lid” lamps will light up 
continuously. The machine is now ready for 
a second cycle. 
If any key is pressed when the machine is 
at the end of the program or if the position 
of the selection knob is changed, the 
“Program Finished” light will go off and only 
the “Lid” lamp will remain as lit. If the door 
is still locked, the “Lid” light will continue flashing until the door is unlocked. 
Press the “On/Off” button to shut down the 
machine.
5 Maintenance and cleaning
Detergent DrawerRemove any powder residue buildup in the 
drawer. To do this;
1.  Press the dotted point on the siphon 
in the softener compartment and pull 
towards you until the compartment is 
removed from the machine.
C If more than a normal amount of 
water and softener mixture starts to 
gather in the softener compartment, the siphon must be cleaned.
2.  Wash the dispenser drawer and the 
siphon with plenty of lukewarm water in a washbasin. 
3.  Replace the drawer into its housing 
after cleaning.  Check if the siphon is in its original location.
Inlet water filtersThere is a filter at the end of each water intake valve at the back side of the machine and also at the end of each water intake 
hose where they are connected to the tap. 
These filters prevent the foreign substances 
and dirt in the water to enter into the machine. Filters should be cleaned as they 
get dirty.
•  Close the taps.
•  Remove the nuts of the water intake 
hoses to clean the surfaces of the filters on the water intake valves with 
an appropriate brush.
•  If the filters are very dirty, you can 
pull them out by means of pliers and clean them.
•  Take out the filters on the flat ends of 
the water intake hoses together with 
the gaskets and clean thoroughly 
under streaming water.
•  Replace the gaskets and filters 
 
						

							
10 - EN
•   Place a large container at the end of the hose. Drain the water off into the 
container by pulling out the plug at the end of the hose. If the amount of 
water to be drained off is greater than 
the volume of the container, replace 
the plug, pour the water out, then 
resume the draining process.
•   After draining process is completed,  replace the plug into the end of the 
hose and fit the hose back into its place.
If your product is not supplied with an 
emergency drain hose, do the following as 
shown in the figure below:
•   Place a large container in front of the  filter to receive water flowing from the 
filter.
•   Loosen pump filter (anticlockwise) 
until water starts to flow out of it. 
Direct the flowing water into the 
container you have placed in front of 
the filter. You can use a piece of cloth 
to absorb any spilled water.
•   When there is no water left, turn the 
pump filter until it is completely loose 
and remove it.
•   Clean any residues inside the filter  as well as fibers, if any, around the 
propeller region.
•   If your product has a water jet  feature, be sure to fit the filter into its 
housing in the pump. Never force the 
filter while replacing it into its housing. 
Fit the filter fully into its housing; 
otherwise, water may leak from the 
filter cap.
4- Close the filter cap.
Close the two-piece filter cap of your 
product by pushing the tab on it.
Close the one-piece filter cap of your 
product by fitting the tabs on the bottom 
into their positions and pushing the upper part of it.
carefully to their places and tighten 
the hose nuts by hand.
Draining any remaining water and 
cleaning the pump filterYour product is equipped with a filter 
system which ensures a cleaner water 
discharge that extends pump life by 
preventing solid items such as buttons, 
coins and fabric fibers from clogging the 
pump propeller during discharge of the 
washing water.
•   If your machine fails to drain the 
water, the pump filter may be 
clogged. You may have to clean 
it every 2 years or whenever it is 
plugged. Water must be drained off 
to clean the pump filter. 
In addition, water may have to be drained 
off completely in the following cases:
•   before transporting the machine (e.g. 
when moving house)
•   when there is the danger of frost
In order to clean the dirty filter and 
discharge the water;
1- Unplug the machine to cut off the supply 
power.
A There may be water at 90°C in the  machine. Therefore, the filter must 
be cleaned only after the inside water 
is cooled down to avoid hazard of 
scalding.
2- Open the filter cap. The filter cap may be 
composed of one or two pieces according 
to the model of your machine.
If it is composed of two pieces, press the 
tab on the filter cap downwards and pull the 
piece out towards yourself.
If it is composed of one piece, hold it from 
both sides and open it by pulling out.
3- An emergency drain hose is supplied 
with some of our models. Others are not 
supplied with this item.
If your product is supplied with an 
emergency drain hose, do the following as 
shown in the figure below:
•  Pull out the pump outlet hose from its 
housing.