BEKO WMB 91242LC User Manual

21EN
Programme and consumption table
EN2Auxiliary functions
Programme (°C)
Max. Load (kg)Water Consumption (l)Energy Consumption (kWh)Max. Speed***ЗамачиваниеБыстрая стиркаДополнител\fное полосканиеЛегкая глажкаRinse HoldPet hair removal
Selectable temperature range °C
\bлопок909872.701600••••••90-Cold
\bлопок609851.801600••••••90-Cold
\bлопок409851.001600••••••90-Cold
Детская909802.701600*•90-30
\bлопок Эко60**9661.351600••••••60-Cold
\bлопок Эко409800.951600••••••60-Cold...

22EN
• : Selectable
* : Automatically selected, no canceling.
** : Energy Label programme (EN 60456)
 *** If maximum spin speed of the machine is lower then this value, you \
can only select up to the maximum spin speed.
- : See the programme description for maximum load.
C The auxiliary functions in the table may vary according to the model of your machine.
C Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature, ambient temperature, type and...

23EN
Auxiliary function selection
Select the desired auxiliary functions before starting the programme. Furthermore, you may also select or cancel auxiliary functions that are suitable to the running programme by pressing 
the Start / Pause / Cancel button when the machine is operating. For this, the machine must be in a step before the auxiliary function you are going to select or cancel.
Depending on the programme, press a, b, c or d buttons to select the desired auxiliary function. Symbol of the...

24EN
• Pet hair removal
This function helps to remove pet hair that remain on your garments more effectively.
When you select this function, Prewash and Extra Rinse steps are added to the normal programme. Thus, washing is performed with more water (30%) and the pet hair is removed more effectively.
A Never wash your pets in the washing machine.
Time display
Remaining time to complete the programme appears on the display while the programme is running. Tim is displayed as “01:30” in hours and minutes...

25EN
Starting the programme
1. Press Start / Pause / Cancel button to start the programme.
2. Start symbol showing the startup of the programme will turn on.
3. Loading door is locked and Door Locked symbol appears on the display.
4. The symbol of the step from which the programme has started appears on the display (Prewash, Main Wash, Rinse, Softener and Spin).
Progress of programme
Progress of a running programme is indicated on the display with a set of symbols.
Relevant symbol appears on the display...

26EN
5.  Make changes in auxiliary functions, temperature and speed settings if necessary.
6.  Press Start / Pause / Cancel button to start the machine.
C The loading door will not open if the water temperature in the machine is high or the water level is above the door opening.
Child Lock
Use Child Lock function to prevent children from tampering with the machine. Thus you can avoid any changes in a running programme.
C You can switch on and off the machine with On / Off button when the Child Lock is...

27EN
6 Maintenance and cleaning
Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals.
Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every 4-5 washing cycles) as shown below in order to prevent accumulation of powder detergent in time.
1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine.
C If more than normal amount of water and...

28EN
1. Close the taps.
2. Remove the nuts of the water intake hoses to access the filters on the water intake valves. Clean them with an appropriate brush. If the filters are too dirty, take them out by means of pliers and clean them.
3. Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water.
4. Replace the gaskets and filters carefully in their places and tighten the hose nuts by hand.
Draining remaining water and 
cleaning the...

29EN
at the end of the hose. When the container is full, block the inlet of the hose by replacing the plug. After the container is emptied, repeat the above procedure to drain the water in the machine completely.
c. When draining of water is finished, close the end by the plug again and fix the hose in its place.
d. Turn the pump filter to take it out.
Discharging the water when the product does not have an emergency draining hose:
a. Place a large container in front of the filter to catch water from the...

30EN
7 Troubleshooting
Programme cannot be started or selected. 
• Washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). >>> Press and hold Start / Pause / Cancel button for 3 seconds to reset the machine to factory settings. (See "Canceling the programme")
Water in the machine.
• Some water might have remained in the product due to the quality control processes in the production. >>> This is not a failure; water is not harmful to the...