BEKO WMB 91242LC User Manual

							21EN
Programme and consumption table
EN2Auxiliary functions
Programme (°C)
Max. Load (kg)Water Consumption (l)Energy Consumption (kWh)Max. Speed***ЗамачиваниеБыстрая стиркаДополнител\fное полосканиеЛегкая глажкаRinse HoldPet hair removal
Selectable temperature range °C
\bлопок909872.701600••••••90-Cold
\bлопок609851.801600••••••90-Cold
\bлопок409851.001600••••••90-Cold
Детская909802.701600*•90-30
\bлопок Эко60**9661.351600••••••60-Cold
\bлопок Эко409800.951600••••••60-Cold
Синтетика604551.001000••••••60-Cold
Синтетика404550.521000••••••60-Cold
Экономичная 20º203.5450.161600•20
Микс 40404550.621000••••••40-Cold
Одеяло40-600.60100060-40
Экспресс 14’302420.101400••30-Cold
Ежедневная909702.021400••90-Cold
Ежедневная609701.201400••90-Cold
Ежедневная309800.301400••90-Cold
Шерст\f402560.301000••40-Cold
Ручная301.5400.25100030-Cold
Темные вещи404950.601000*•40-Cold
Самоочистка70-1102.00800*70
Освежающая-2350.031000•-
  
						

							22EN
• : Selectable
* : Automatically selected, no canceling.
** : Energy Label programme (EN 60456)
 *** If maximum spin speed of the machine is lower then this value, you \
can only select up to the maximum spin speed.
- : See the programme description for maximum load.
C The auxiliary functions in the table may vary according to the model of your machine.
C Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions and spin speed, and changes in electr\
ic voltage.
C You can see the washing time of the programme you have selected on the display of the machine. It is normal that small differences may occur between the time shown on the display and the real washing time.
  
						

							23EN
Auxiliary function selection
Select the desired auxiliary functions before starting the programme. Furthermore, you may also select or cancel auxiliary functions that are suitable to the running programme by pressing 
the Start / Pause / Cancel button when the machine is operating. For this, the machine must be in a step before the auxiliary function you are going to select or cancel.
Depending on the programme, press a, b, c or d buttons to select the desired auxiliary function. Symbol of the selected auxiliary function appears on the display.
abc d
C Some functions cannot be selected together. If a second auxiliary function conflicting with the first one is selected before starting the machine, the function selected first will be canceled and the second auxiliary function selection will remain active. For example, if you want to select Quick Wash after you have selected the Prewash, Prewash will be canceled and Quick Wash will remain active.
C An auxiliary function that is not compatible with the programme cannot be selected. (See "Programme and consumption table")
C Auxiliary Function buttons may vary according to the model of the 
machine.
• Замачивание (Prewash)
A Prewash is only worthwhile for heavily soiled laundry. Not using the Prewash will save energy, water, detergent and time.
F1 appears on the display when you select this function (a).
• Быстрая стирка (Quick Wash)
This function can be used in Cottons and 
Synthetics programmes. It decreases the 
washing times and also the number of rinsing steps for lightly soiled laundry.
F2 appears on the display when you select this function (b).
C When you select this function, load your machine with half of the 
maximum laundry specified in the programme table.
• Дополнительное полоскание (Rinse Plus)
This function enables the machine to make another rinsing in addition to the one already made after the main wash. Thus, the risk for sensitive skins (babies, allergic skins, etc.) to be effected by the minimal detergent remnants on the laundry can be reduced.
F3 appears on the display when you select this function (c).
• Легкая глажка (Anti-Creasing)
This function creases the clothes lesser when they are being washed. Drum movement is reduced and spinning speed is limited to prevent creasing. In addition, washing is done with a higher water level.
F4 appears on the display when you select this function (d).
• Rinse Hold
If you are not going to unload your clothes immediately after the programme completes, you may use rinse hold function to keep your laundry in the final rinsing water in order to prevent them from getting wrinkled when there is no water in the machine. Press Start / Pause /Cancel button after this process if you want to drain the water without spinning your laundry. Programme will resume and complete after draining the water.
If you want to spin the laundry held in water, adjust the Spin Speed and press Start / Pause / Cancel button.
The programme resumes. Water is drained, laundry is spun and the programme is completed.
• Soaking
The Soaking auxiliary function ensures better removal of stains ingrained into the clothes by holding them in the detergent water prior to startup of the programme.
  
						

							24EN
• Pet hair removal
This function helps to remove pet hair that remain on your garments more effectively.
When you select this function, Prewash and Extra Rinse steps are added to the normal programme. Thus, washing is performed with more water (30%) and the pet hair is removed more effectively.
A Never wash your pets in the washing machine.
Time display
Remaining time to complete the programme appears on the display while the programme is running. Tim is displayed as “01:30” in hours and minutes format.
C  Programme time may differ from the values in the "Programme and consumption table" depending on the water pressure, water hardness and temperature, ambient temperature, amount and the type of laundry, auxiliary functions selected and the changes at the mains voltage.
Delayed start
With the Delayed Start function the startup of the programme may be delayed up to 24 hours. Delayed start time can be increased by increments of 30 minutes. 
C Do not use liquid detergents when you set Delayed Start! There is the risk of staining of the clothes.
1.  Open the loading door, place the laundry and put detergent, etc.
2. Select the washing programme, temperature, spin speed and, if required, the auxiliary functions.
3. Set the desired delayed start time by pressing the Delayed Start + or - buttons. Delayed Start symbol flashes.
4.  Press Start / Pause / Cancel button. Delayed start countdown starts. Delayed Start symbol illuminates steadily. Start symbol appears. “:” sign in the middle of the delayed start time on the display starts flashing.
C Additional laundry may be loaded during the delayed start period. At the end of the countdown, Delayed Start symbol disappears, washing cycle starts and the time of the selected programme appears on the display.
Changing the delayed start period
If you want to change the time during countdown:
1.  Press Start / Pause / Cancel button. “:” sign in the middle of the delayed start time on the display stops flashing. Pause symbol appears. Delayed Start symbol flashes. Start symbol disappears.
2. Set the desired delayed start time by pressing the Delayed Start + or - buttons.
3. Press Start / Pause / Cancel button. Delayed Start symbol illuminates steadily. Pause symbol disappears. Start symbol appears.
4. “:” sign in the middle of the delayed start time on the display starts flashing.
Canceling the Delayed Start function
If you want to cancel the delayed start countdown and start the programme immediately:
1. Press Start / Pause / Cancel button. “:” sign in the middle of the delayed start time on the display stops flashing.
2. Start symbol disappears. Pause symbol and Delayed Start symbol flashes.
3. Decrease the delayed start time by pressing the Delayed Start - button. Programme duration appears after 30 minutes.
4. Press Start / Pause / Cancel button to start the programme.
  
						

							25EN
Starting the programme
1. Press Start / Pause / Cancel button to start the programme.
2. Start symbol showing the startup of the programme will turn on.
3. Loading door is locked and Door Locked symbol appears on the display.
4. The symbol of the step from which the programme has started appears on the display (Prewash, Main Wash, Rinse, Softener and Spin).
Progress of programme
Progress of a running programme is indicated on the display with a set of symbols.
Relevant symbol appears on the display at the beginning of each programme step and all symbols remain lit at the end of the programme. The farthermost right symbol indicates the current programme step.
Prewash
If the Prewash auxiliary function is selected, Prewash symbol appears on the display indicating that the prewash step has started.
Main Wash
Main Wash symbol indicating that the 
main wash step has started appears on the display.
Rinse
Rinse symbol indicating that the rinsing step has started appears on the display.
Softener
Softener symbol indicating that the softener step has started appears on the display. 
Spin
Appears at the beginning of the final spin step and remains lit during Spin and Pump special programmes.
C If the machine does not pass to the spinning step, Rinse Hold function might be active or the automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry 
in the machine.
Loading door lock
There is a locking system on the loading door of the machine that prevents opening of the door in cases when the water level is unsuitable.
Door Locked symbol appears when the loading door is locked. This symbol will flash until the loading door becomes ready to open when programme completes or the machine is paused. Do not force to open the loading door in this step. Symbol disappears when the door is ready to open. You can open the door 
when the symbol disappears.
Changing the selections after 
programme has started
Switching the machine to pause mode
Press the Start / Pause / Cancel button to switch the machine to pause mode. Pause symbol appears on the display indicating that the machine is paused. Start symbol disappears.
F2F4F1F3
Changing the speed and temperature 
settings for auxiliary functions
Depending on the step the programme has reached, you may cancel or activate the auxiliary functions; see, "Auxiliary function selection". 
You may also change the speed and temperature settings; see, "Spin speed selection" and "Temperature selection".
Adding or taking out laundry
1.  Press the Start / Pause / Cancel button to switch the machine to 
pause mode. The programme follow-up light of the relevant step during which the machine was switched into 
the pause mode will flash.
2. Wait until the Loading Door can be opened.
3. Open the Loading Door and add or take out the laundry.
4. Close the Loading Door.
  
						

							26EN
5.  Make changes in auxiliary functions, temperature and speed settings if necessary.
6.  Press Start / Pause / Cancel button to start the machine.
C The loading door will not open if the water temperature in the machine is high or the water level is above the door opening.
Child Lock
Use Child Lock function to prevent children from tampering with the machine. Thus you can avoid any changes in a running programme.
C You can switch on and off the machine with On / Off button when the Child Lock is active. When you switch on the machine again, programme will resume from where it has stopped.
To activate the Child Lock:
Press and hold 2nd and 4th Auxiliary Function buttons for 3 seconds. “Con” appears on the display.
C Same phrase will appear on the display if you press any button when Child Lock is enabled.
To deactivate the Child Lock:
Press and hold 2nd and 4th Auxiliary Function buttons for 3 seconds. “COFF” appears on the display.
C Do not forget to disable the child lock at the end of the programme if it was enabled before. Otherwise, machine will not allow to select a new programme.
Canceling the programme
Press and hold Start / Pause / Cancel button for 3 seconds. Start symbol 
flashes. Symbol of the step at which the programme was cancelled remains lit. "End" appears on the display and the programme is cancelled.
C If you want to open the loading door after you have cancelled the programme but it is not possible to open the loading door since the water level in the machine is above the loading door opening, then turn the Programme Selection knob to Pump+Spin programme and discharge the water in the machine.
Machine is in Rinse Hold mode
Spin symbol flashes and Pause symbol illuminates when the machine is in Rinse Hold mode.
If you want to spin your laundry when the machine is in this mode:
Adjust the spin speed and press Start / Pause / Cancel button. Pause symbol disappears and Start symbol appears. Programme resumes, discharges the water and spins the laundry.
If you only want to drain the water without spinning:
Just press Start / Pause / Cancel button. Pause symbol disappears. Start symbol appears. Programme resumes and discharges the water only.
End of programme
“End” appears on the display at the end of the programme. Symbols of the programme steps remain lit. Auxiliary function, spin speed and temperature that were selected at the beginning of the programme remain selected.
  
						

							27EN
6 Maintenance and cleaning
Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals.
Cleaning the detergent drawer
Clean the detergent drawer at regular intervals (every 4-5 washing cycles) as shown below in order to prevent accumulation of powder detergent in time.
1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine.
C If more than normal amount of water and softener mixture starts to gather in the softener compartment, the 
siphon must be cleaned.
2.  Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin. Wear protective gloves or use an appropriate brush to avoid touching of the residues in the drawer with your skin when cleaning.
3. Insert the drawer back into its place after cleaning and make sure that it is seated well.
Cleaning the loading 
door and the drum
Residues of softener, detergent and dirt may accumulate in your machine in time and may cause unpleasant odours and washing complaints. To avoid this, use the Drum Cleaning programme. If your machine is not featured with Drum Cleaning programme, use Cottons-90 programme and select Additional Water or Extra Rinse auxiliary functions as well. 
Before starting the programme, put max. 100 g of powder anti-limescale into the main wash detergent compartment (compartment nr. II). If the anti-limescale 
is in tablet form, put only one tablet into compartment nr. II. Dry the inside of the bellow with a clean piece of cloth after the programme has come to an end. 
C Repeat Drum Cleaning process in every 2 months.
C Use an anti-limescale suitable for the washing machines. 
After every washing make sure that no foreign substance is left in the drum.
If the holes on the bellow shown in the figure is blocked, open the holes using a toothpick.
C Foreign metal substances in your machine will cause rust stains. Clean the stains on the drum surface by using cleaning agents for stainless steel. Never use steel wool 
or wire wool.
Cleaning the body 
and control panel
Wipe the body of the machine with soapy water or non-corrosive mild gel detergents as necessary, and dry with a soft cloth.
Use only a soft and damp cloth to clean the control panel.
A Never use sponge or scrub materials. These will damage the painted and plastic surfaces.
Cleaning the water 
intake filters
There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected 
to the tap. These filters prevent foreign substances and dirt in the water to enter the washing machine. Filters 
should be cleaned as they do get dirty.
  
						

							28EN
1. Close the taps.
2. Remove the nuts of the water intake hoses to access the filters on the water intake valves. Clean them with an appropriate brush. If the filters are too dirty, take them out by means of pliers and clean them.
3. Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water.
4. Replace the gaskets and filters carefully in their places and tighten the hose nuts by hand.
Draining remaining water and 
cleaning the pump filter
The filter system in your machine prevents solid items such as buttons, coins and fabric fibers clogging the pump impeller 
during discharge of washing water. Thus, the water will be discharged without any problem and the service life of the pump will extend.
If the machine fails to drain water, the pump filter is clogged. Filter must be cleaned whenever it is clogged or in every 3 months. Water must be drained off first to clean the pump filter.
In addition, prior to transporting the machine (eg., when moving to another house) and in case of freezing of the water, water may have to be drained completely.
A Foreign substances left in the pump filter may damage your machine or may cause noise problem.
In order to clean the dirty filter and discharge the water:
1.  Unplug the machine to cut off the 
supply power.
A Temperature of the water inside the machine may rise up to 90 ºC. 
To avoid burning risk, filter must be cleaned after the water in the machine cools down.
2.  Open the filter cap.
 If the filter cap is composed of two pieces, press the tab on the filter cap downwards and pull the piece out towards yourself.
If the filter cap is one piece, pull the cap from both sides at the top to open.
C You can remove the filter cover by slightly pushing downwards with a thin plastic tipped tool, through the gap above the filter cover. Do not use metal tipped tools to remove the cover.
3.  Some of our products have emergency draining hose and some does not have. Follow the steps below to discharge the water.
Discharging the water when the product has an emergency draining hose:
a. Pull the emergency draining hose out from its seat
b. Place a large container at the end of the hose. Drain the water into the container by pulling out the plug 
  
						

							29EN
at the end of the hose. When the container is full, block the inlet of the hose by replacing the plug. After the container is emptied, repeat the above procedure to drain the water in the machine completely.
c. When draining of water is finished, close the end by the plug again and fix the hose in its place.
d. Turn the pump filter to take it out.
Discharging the water when the product does not have an emergency draining hose:
a. Place a large container in front of the filter to catch water from the filter.
b. Loosen pump filter (anticlockwise) until water starts to flow. Fill the flowing water into the container you have placed in front of the filter. Always keep a piece of cloth handy to absorb any spilled water.
c. When the water inside the machine is finished, take out the filter completely by turning it.
4. Clean any residues inside the filter as well as fibers, if any, around the pump impeller region.
5. Install the filter.
A If your product has a water jet feature, be sure to fit the filter into its housing in the pump. Never force the filter while installing it into its housing. Seat the filter into its place completely. Otherwise, water may leak from the filter cap.
6.  If the filter cap is composed of two pieces, close the filter cap by pressing on the tab. If it is one piece, seat the tabs in the lower part into their places first, and then press the upper part to close.
   
						

							30EN
7 Troubleshooting
Programme cannot be started or selected. 
• Washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). >>> Press and hold Start / Pause / Cancel button for 3 seconds to reset the machine to factory settings. (See "Canceling the programme")
Water in the machine.
• Some water might have remained in the product due to the quality control processes in the production. >>> This is not a failure; water is not harmful to the machine.
There is water leaking from the bottom of the washing machine.
• Likely problems with hoses or the pump filter. >>> Be sure the seals of the water inlet hoses are securely fitted. Attach the hose to the tap tightly.
• Pump filter might not be closed fully. >>> Make sure that the pump filter is completely closed.
Machine does not fill with water.
• Tap is turned off. >>> Open the inlet water taps fully.
• Water inlet hose is bent. >>> Flatten the water inlet hose.
• Water inlet filter is clogged. >>> Clean the water inlet filter.
• The loading door is ajar. >>> Close the Loading Door.
Machine does not drain water.
• Water drain hose might be clogged or twisted. >>> Clean or flatten the hose.
• Pump filter is clogged. >>> Clean the pump filter.
Machine vibrates or makes noise.
• Machine might be standing unbalanced. >>> Adjust the feet to level the machine.
• A hard substance might have entered into the pump filter. >>> Clean the pump filter.
• Transportation safety bolts are not removed. >>> Remove the transportation safety bolts.
• Laundry quantity in the machine might be too little. >>> Add more laundry to the machine.
• Machine might be overloaded with laundry. >>> Take out some of the laundry from the machine or distribute the load by hand to balance it homogenous\
ly in the machine.
• Machine might be leaning on a rigid item. >>> Make sure that the machine is not leaning on anything.
Machine stopped shortly after the programme started.
• Machine might have stopped temporarily due to low voltage. >>> It will resume running when the voltage restores to the normal level.
Machine directly discharges the water it takes in.
• Draining hose might not be at adequate height. >>> Connect the water draining hose as described in the operation manual.
No water can be seen in the machine during washing.
C The water level is not visible from outside of the washing machine. This is not a failure.