BEKO WMB 81231 User Manual

21EN
• : Selectable
* :  Automatically selected, no canceling.
** :  Energy Label programme (EN 60456)
*** :  If maximum spin speed of the machine is lower then this value, you can o\
nly select 
up to the maximum spin speed.
- :  See the programme description for maximum load.
C Water and power consumption may vary subject to the changes in water pressure, 
water hardness and temperature, ambient temperature, type and amount of 
laundry, selection of auxiliary functions and spin speed, and changes in...

22EN
Auxiliary function selection
Select the desired auxiliary functions 
before starting the programme. 
Furthermore, you may also select or 
cancel auxiliary functions that are suitable 
to the running programme without 
pressing the Start / Pause button when 
the machine is operating. For this, the 
machine must be in a step before the 
auxiliary function you are going to select 
or cancel.
If the auxiliary function cannot be selected 
or canceled, light of the relevant auxiliary 
function will blink...

23EN
C Do not use liquid detergents when 
you set Delayed Start! There is the 
risk of staining of the clothes.
1.  Open the loading door, place the 
laundry and put detergent, etc.
2.  Select the washing programme, 
temperature, spin speed and, if 
required, the auxiliary functions.
3.   Set the desired time by pressing the 
Delayed Start button.
4.   Press Start / Pause button. The 
delayed start time you have set is 
displayed. Delayed start countdown 
starts. “_” symbol next to the delayed 
start...

24EN
any programme is running. The lights on 
the 1st and 2nd Auxiliary Function buttons 
will flash, and "C03", "C02", "C01" will 
appear on the display respectively while 
you keep the buttons pressed for 3 
seconds. Then, "COFF" will appear on 
the display indicating that the Child Lock 
is deactivated.
C  In addition to the method above, to 
deactivate the Child Lock, switch the 
Programme Selection knob to On 
/ Off position when no programme 
is running, and select...

25EN
programme will be canceled. End / 
Cancel light will flash continuously to 
notify that the programme has been 
canceled. 
Pump function is activated for 1-2 
minutes regardless of the programme 
step, and whether there is water in the 
machine or not. After this period, your 
machine will be ready to start with the 
first step of the new programme.
C Depending on the step where the 
programme was canceled in, you 
may have to put detergent and 
softener again for the programme 
you have selected...

26EN
6 Maintenance and cleaning
Service life of the product extends and 
frequently faced problems decrease if 
cleaned at regular intervals.
Cleaning the detergent drawer
Clean the detergent drawer at regular 
intervals (every 4-5 washing cycles) 
as shown below in order to prevent 
accumulation of powder detergent in 
time.
1.  Press the dotted point on the siphon 
in the softener compartment and pull 
towards you until the compartment is 
removed from the machine.
C If more than normal amount of water...

27EN
1. Close the taps.
2.  Remove the nuts of the water intake 
hoses to access the filters on the 
water intake valves. Clean them with 
an appropriate brush. If the filters are 
too dirty, take them out by means of 
pliers and clean them.
3.  Take out the filters on the flat ends of 
the water intake hoses together with 
the gaskets and clean thoroughly 
under running water.
4.  Replace the gaskets and filters 
carefully in their places and tighten 
the hose nuts by hand.
Draining remaining water and...

28EN
at the end of the hose. When the 
container is full, block the inlet of 
the hose by replacing the plug. After 
the container is emptied, repeat the 
above procedure to drain the water in 
the machine completely.
c.  When draining of water is finished, 
close the end by the plug again and 
fix the hose in its place.
d.  Turn the pump filter to take it out.
Discharging the water when the product 
does not have an emergency draining 
hose:
a.  Place a large container in front of the 
filter to catch...

29EN
7 Troubleshooting
Programme cannot be started or selected. 
•  Washing machine has switched to self protection mode due to a supply problem 
(line voltage, water pressure, etc.). >>> Press and hold Start / Pause / Cancel 
button for 3 seconds to reset the machine to factory settings. (See "Canceling the 
programme")
Water in the machine.
•  Some water might have remained in the product due to the quality control 
processes in the production. >>> This is not a failure; water is not harmful to...

30EN
Loading door cannot be opened.
• Door lock is activated because of the water level in the machine. >>> Drain the 
water by running the Pump or Spin programme.
•  Machine is heating up the water or it is at the spinning cycle. >>> Wait until the 
programme completes.
•  Child lock is engaged. Door lock will be deactivated a couple of minutes after 
the programme has come to an end. >>> Wait for a couple of minutes for 
deactivation of the door lock.
Washing takes longer time than the one specified in...