Barco Projector Cineversum 80 User Manual

4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM
Using the Remote Control
1. Point the Remote Control to the front of the Cine VERSUM Master or to the Cine VERSUM 80.
2. Press the standby button
. (image 4-9)
TheCineVERSUMMasterandtheCineVERSUM80gofromOPERATIONtoSTANDBY.
Image 4-9
4.3.2 From STANDBY mode to OPERATION mode
Using the Jog dial on the Cine VERSUM Master
1. Rotate the jog dial until “Power up” in the menu on the Cine VERSUM Master is pointed.
2. Press jog dial to activate the selection.
The Cine...

4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM
Image 4-12
Economic standby
Using the Remote Control
1. Point the Remote Control to the front of the Cine VERSUM Master or to the Cine VERSUM 80
2. Toggle with the↑or↓arrow keys until “Economic” in the menu on the Cine VERSUM Master is pointed to (image 4-11).
3. PressENTERto activate selection.
The Cine VERSUM Master and the Cine VERSUM 80 go from STANDBY to Economic STANDBY. The economic standby is
visualized in the Master display with a Zzzzz-message with...

4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM
4.6 Turning ON the system from total OFF mode
How to turn ON the system back to Operation mode
1. Press the power switch on the Cine VERSUM Master (image 4-1).
The Cine VERSUM Master goes from OFF to standby. (image 4-15)
2. Press the power switch on the Cine VERSUM 80 (image 4-2).
The Cine VERSUM 80 goes from OFF to standby.
3. Turning on to operation mode, see From STANDBY mode to OPERATION mode, page 17.
Image 4-15
R5976490 CINE VERSUM SYSTEM 1701200319 

4. SWITCHING ON/OFF THE CINE VERSUM SYSTEM
20R5976490 CINE VERSUM SYSTEM 17012003 

5. Direct source selection
5. DIRECT SOURCE SELECTION
5.1 From standby mode
Using the digit buttons on the Remote Control
1. Make sure that the connected sources to the Cine VERSUM Master are turned on.
2. Using the digit button on the Remote Control, key in the corresponding slot number (from 1 to 8). (image 5-1)
The Cine VERSUM Master powers up and starts on its turn powering up the connected displays. Image of the selected source
appears on the display.
Image 5-1
Digit buttons on Remote Control
Using...

5. Direct source selection
5.2 Return to standby mode
How to return to standby remotely
1. Point the Remote Control to the front of the Cine VERSUM Master or the Cine VERSUM 80.
2. Press the standby button on the Remote Control again. (image 5-2)
The Cine VERSUM Master switches to the standby mode and switches on its turn the connected display into the standby mode.
When switching the Cine VERSUM 80 into the standby mode, a cool down period for the lamp of about 1
minute is activated. As a result,...

6. IMAGE CONTROL
6. IMAGE CONTROL
Image controls
The Brightness, Contrast, Sharpness (Detail), Color and Tint functions are directly accessible with the Remote Control.
The adjustment functions, when selected, display a slide bar overlayed on the source image.
It is useful to adjust the Brightness, whenever the ambient room lightning changes. The same is true for
Contrast. Please note that for the best result, it is advised to first change the Brightness, then the Contrast.
6.1 Brightness Control
How to...

6. IMAGE CONTROL
Image 6-3
Image 6-4
6.3 Sharpness (Detail) Control
How to adjust the Sharpness
The Sharpness function is used to adjust the image sharpness of video signals when using a video decoder installed in the Cine
VERSUM Master.
To adjust the Sharpness, press the(+)or(-)side of the button ’SHARP’ (image 6-5). The following barscale is overlayed on the
source image,image 6-6.
Press the(+)or(-)button until the sharpest display is attained. Detail level should be roughly proportional to the input...

6. IMAGE CONTROL
6.4 Color (Saturation) Control
How to adjust the Color (Saturation)
The Color function is used to adjust color saturation levels and is only active for Video and S-Video sources.
To adjust Color, press the(+)or(-)side of the button ’COLOR’ (image 6-7). The following barscale is overlayed on the source image,
image 6-8.
Press the(+)or(-)button until the desired color saturation level is displayed. If color is set to a 0% level, the result will be black and
white picture. If the color is...

6. IMAGE CONTROL
Image 6-9
Image 6-10
26R5976490 CINE VERSUM SYSTEM 17012003