Barco Hdx Series Installation Manual

5. Getting started
• Package version
•Mgrsoftware
• GUI software
Starting image projection via the standby key.
1. PressStand bykey once on the local keypad or on the remote control.
MENU
EXIT
ENTER
PA U S ETEXT
PHASE
TINT
COLOR
BRIGHTN
CONTR
90
78
56
3
4
12
LENS
LENS
ZOOMLENS
SHIFT
LENS
FOCUS

SHARPN
LENS
SHIFT
5*%3$77(513,3
:,12:
5,**,1*
$872,0$*(1234
5
6
7890MENUEXIT
ENTER
RGB
STBY
PA U S E
TEXTPATTERN
WINDOW
PIP
LENS
AUTO
Fn
Image 5-6
Standby key indication
The projector starts up on the last saved...

5. Getting started
5.4 Switching to standby
How to switch to standby
1. Press and holdStandbyfor 3 seconds on the local keypad or the remote control. In the mean time the messageKeep on
pressing...is displayed. This message changes toSaving data ...
The projector goes to standby.
All custom settings are written to the internal backup device. A message ’Saving data ...’ indicates this
process. Never switch off the projector while this message is displayed.
When switching to standby, an after cooling...

5. Getting started
5.5 Power off projector
How to power off
1. PressfirstStandby.
2. Let cool down the projector until the fan speed decrease. At least 5 minutes.
3. Switch off the projector with the power switch. ’0’ must be pressed.
CAUTION:Never switch off the projector while the message ’Saving data ... ’ is displayed !
R5905032 HDX SERIES 23/11/201169 

5. Getting started
5.6 Status LEDs
Overview
LED
Color statusDescription
Red on Projector is in standby
Red toggles on/off Projector startup failed, no lamp power supply
Green toggles on/offProjector starts up
Green onProjector is on
White toggles on/off From/To ECO standby
Standby button
Dimmed white Projector powers up
Red on
Shutter is closed
Green on Shutter is open
Dimmed white
Shutter is closed, projector in standby
Full white
Shutter is undefined (shutter not open and not closed)
Pause button
Full...

5. Getting started
5.7 Using the RCU
Pointing to the reflective screen
1. Point the front of the RCU to the reflective screen surface.
F1F2F3
F4
F5
ADJ
EX
IT
EN
TERPA
USEPH
ASETE
XTSHAR
PN
TI
NT
COLO
R
BR
IGHT N
CONT R
TR
EB
LEBA
LA
NCE
BASS
VO
L90
7856
34
12
Image 5-7
IR control via reflective screen
Hardwired to the XLR input
1. Plug one end of the remote cable in the connector on the bottom of the RCU.
2. Plug the other end in the big connector on the communication interface of the projector,...

5. Getting started
5.8 Projector Address
72R5905032 HDX SERIES 23/11/2011 

5. Getting started
5.8.1 Displaying and Programming addresses into the RCU
Displaying the Projector Address on the Screen.
1. PressAddresskey (recessed key on the RCU) with a pencil.
The projector’s address is displayed on the local LCD screen.
To continue using the RCU with that specific address, it is necessary to enter the same address with the
digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the
Address key displays projector address 3, then...

5. Getting started
5.8.2 Controlling the projector
Projector address
Address installed in the projector to be individually controlled.
Common address
Projector will always execute the command coming from a RCU programmed with that common address.
Why a projector address ?
As more than one projector can be installed in a room, each projector should be separately addressable with an RCU or computer.
Therefore each projector has its own address.
Set up an individual Projector Address.
The set up of a...

5. Getting started
5.9 Source selection
Source selection when no picture in picture is active
Use the digit keys on the remote control or local keypad to activate the desired source.
Source selection when picture in picture is active
Use theWindowbutton on the remote control or the local keypad to select the main window or the picture in picture (PiP) window.
MENU
EXIT
ENTER
PA U S ETEXT
PHASE
TINT
COLOR
BRIGHTN
CONTR
90
78
56
3
4
12
LENS
LENS
ZOOMLENS
SHIFT
LENS
FOCUS

SHARPN
LENS
SHIFT
5*%3$77(513,3...

5. Getting started
76R5905032 HDX SERIES 23/11/2011