Home > Barco > Projector > Barco Hdx Series Installation Manual

Barco Hdx Series Installation Manual

Here you can view all the pages of manual Barco Hdx Series Installation Manual. The Barco manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 41

3. Physical installation
Image 3-26
Lock lens
8. Check if the lens is really secured by trying to pull the lens out of the lens holder.
CAUTION:Never transport the projector with a Lens mounted in the Lens Holder. Always remove the Lens
before transporting the projector. Neglecting this can damage the Lens Holder and Prism.
R5905032 HDX SERIES 23/11/201137 

Page 42

3. Physical installation
3.2.4 Lens removal
How to remove
1. Support the lens with one hand while you unlock the lens holder bysliding the lock handle towards the “unlocked” position as
illustrated.
Image 3-27
Lens removal, unlock
2. Gently pull the lens out of the lens holder.
Image 3-28
Lens removal
It’s recommended to place the Lens caps of the original Lens packaging, back on both sides of the removed
Lens to protect the optics of the Lens.
It’s recommended to place the foam rubber of the original...

Page 43

3. Physical installation
3.2.5 Lens shift, zoom & focus
Via Lens key
1. PressLENSkey on the local keypad or the remote control.
The zoom/focus menu opens.
Image 3-29
Zoom/Focus adjustment
2. Use the▲or▼key to zoom the lens.
Use the◄or►key to focus the lens.
PressENTERto switch to Lens shift adjustment.
Image 3-30
Shift adjustment
3. Use the▲or▼key to shift the lens in vertical direction.
Use the◄or►key to shift the lens in horizontal direction.
PressENTERto switch to zoom/focus adjustment.
Via direct...

Page 44

3. Physical installation
3.2.6 Scheimpflug adjustment
What has to be done ?
The lens holder has to be adjusted so that the “sharp focus plane” ofthe projected image falls together with the plane of the screen
(Fp1→Fp2). This is achieved by changing the distance between the DMD plane and the lens plane (Lp1→Lp2). The closer the lens
plane comes to the DMD plane the further the sharp focus plane will be. It can sometimes happen that you won’t be able to get a
complete focused image on the screen due to a...

Page 45

3. Physical installation
Necessary tools
• Allenkey3mm
• Nut driver 13 mm
• Nut driver 10 mm
How to adjust
1. Project a green focus pattern.
Image 3-33
2. Loosen the lock nuts (a, b, c and d). See image 3-32.
3. Loosen the 4 set screws (A, B, C and D) by 1 cm. See image 3-32.
4. Fully loosen lock nut 4. See image 3-32.
5. Optimize the focus of the projected image as follows:
a) Place the zoom lens in TELE position (smallest projected image) and adjust the focus using the lens focus barrel or motorized...

Page 46

3. Physical installation
6. Sharpen bottom left corner of the screen by adjusting nut 1.
1
F
Image 3-35
Left bottom focusing
7. Sharpen bottom right corner of the screen by adjusting nut 2.
2
F
Image 3-36
Right bottom focusing
8. Sharpen top right corner of the screen by adjusting nut 3
42
R5905032 HDX SERIES 23/11/2011 

Page 47

3. Physical installation
3
F
Image 3-37
Corner focusing
9. Repeat from step 6 until the projected focus pattern is as sharp as possible in the center, left, right, top and bottom of the screen.
How tofixtheScheimpflug
Start thefixation as follows (steps must be followed strictly) :
1. Turn in set screw A, B and C. Tighten lightly (by hand).
Tip:Any movement of the image will affect the Scheimpflug adjustment
2. Fasten lock nuts a, b and c.
3. Turn in set screw D lightly (by hand) allowing the image to move...

Page 48

3. Physical installation
3.3 Connecting the projector with the power net
CAUTION:Use only the power cord provided with the projector.
How to connect with local power net
1. Ensure that the power switch stands in the ’0’ (OFF) position (1).
1
2
3
Image 3-39
Power input
2. Connect the female side of the power cord with the power input socket of the projector (2).
3. Secure the power plug by locking the plug holder clamp (3).
4. Connect the male side of the power cord to the local power net.
Caution:Ensure...

Page 49

3. Physical installation
3.4 Alignment of a table mounted projector
How to align
1. Place the projector in the desired location. Take into account the zoom range of the used lens and the size of the screen.
2. Project one of the internal hatch patterns on the screen.
3. Turn the adjustable feet in or out until the projected hatch pattern has a perfect rectangle shape and is leveled.
Image 3-40
Level alignment
When this is achieved, the projector is set horizontal and vertical at right angles to the...

Page 50

3. Physical installation
3.5 Mounting the bottom carry handler
Necessary tools
Open wrench 17 mm
Necessary parts
4x bolt M10 x 16 mm
How to mount
1. Turn the projector upside down.
2. Turn out the 4 feet.
Image 3-42
Remove feet
3. Turn out the feet of the carry handle as far as possible.
Image 3-43
Mount carry handle
46R5905032 HDX SERIES 23/11/2011 
Start reading Barco Hdx Series Installation Manual

Related Manuals for Barco Hdx Series Installation Manual

All Barco manuals