Barco CR Series Projector User Manual

31
5.8 Image alignment
For easier alignment of the projector, test images are built into the system.
To enable test images, go to the menu entry INSTALLATION > TEST IMAGE. Cycle the vari-
ous test images using the arrow keys. When a test image matching the aspect ratio of your 
screen has been found, use the zoom, focus, lens shift and physical projector alignment to 
match the screen.
5.9 Setting image orientation
In relation to the screen, the projector supports the following installation...

32User Manual - Basic setupCR series
User Manual - Basic setup
5.12 Changing the language of the menu system
The projector menu system has a total of 11 user-selectable languages embedded for easier 
use all over the world. The default language is English.
The available languages are:
• English
• French
• German
• Spanish
• Russian
• Norwegian
• Swedish
• Korean
• Japanese
• Chinese Simplified
• Chinese Traditional
• Portuguese
• Italian
To change the language of the menu system, just select “LANGUAGE”...

33
5.15 Configuring 3D (AS3D)
This is information is only applicable to the WUXGA and 1080p versions, \
not WQXGA.
The projector has support for AS3D. AS3D images require active shutter glasses to work. To 
enable active stereo select 3D > 3D MODE. Enabling 3D mode will configure the projector for 
the use with an active stereo source.
The only active stereo 3D format natively supported by the projector is sequential left/
right at a frequency between 100 and 120 Hz. Both DVI and HDMI connectors can be...

34User Manual - Basic setupCR series
User Manual - Basic setup
1920 x 1080 (1080)
5.16 Image sizes
Lens types and specifications may change without prior notice.  
For correct lens information please refer to projectiondesign.com/products/lenses
Projec tion distanc e
Image width
Of
set (8%)
ft
1.98
1.78
1.58
1.39
1.19
0.99
0.79
0.59
0.40
0.20
0.0
m
0.60
0.54
0.48
0.42
0.36
0.30
0.24
0.18
0.12
0.06
0
 
m
12.00
11.00
10.00
9.00
8.00
7.00
6.00
5.00
4.00
3.00
2.00
1.00 0Screen diagonalm
15.00
13.75
12.50...

35
1920 x 1200 (WUXGA)
Projec tion distanc e
Image widthOfset (8%)
ft
1.98
1.78
1.58
1.39
1.19
0.99
0.79
0.59
0.40
0.20
0.0
m
0.60
0.54
0.48
0.42
0.36
0.30
0.24
0.18
0.12
0.06
0
 
m
12.00
11.00
10.00
9.00
8.00
7.00
6.00
5.00
4.00
3.00
2.00
1.00 0Scr een diagonalm
15.00
13.75
12.50
11.25
10.00
8,75
7.50
6.25
5.00
3.75
2.50
1.25 0
Ultra  Wide Angle (EN12)  0.79 : 1 (0.5 - 2.5m)
Wide Angle Z oom (EN13) 1.24 - 1.60 : 1 (1.0 - 15m)
Wide Angle  (EN15) 1.16 :  1  (1.0 - 15m)
Standard Zoom (EN11) 1.60 - 2.32 : 1...

36User Manual - Basic setupCR series
User Manual - Basic setup
2560 x 1600 (WQXGA)  / 2560 x 1080 (panorama)
Wide Angle (EN42) 0.80 : 1 (0.7 -  7m)
Ultra  Wide Angle (EN45)   0.80 - 1.21 : 1  (5 - 30m)
Wi de Angle Z oom (EN43) 1.20  - 1.69 : 1 (1.5 - 15m)
Standard Zoom (EN41) 1.69 - 2.50 : 1 (1.5  - 15m)
Short  Zoom  (EN44) 2.50 - 4.61 : 1 (2.0 – 40 m)
Projec tion distanc e
Image width
Of
set (8%)
ft
1.98
1.78
1.58
1.39
1.19
0.99
0.79
0.59
0.40
0.20
0.0
m
0.60
0.54
0.48
0.42
0.36
0.30
0.24
0.18
0.12...

37
6 Advanced setup
6.1 Controlling multiple projectors with remote control ID (RCID)
The remote control can be operated either in ‘broadcast mode’, or ‘individual mode’. When 
several projectors are in use in an installation, individual control may be convenient. Individual 
control is available either by wired remote control, using the data-jack, or by using an individ-
ual number code. For individual control, first set the individual RC ID code using the projector 
menu system, see the SETTINGS sub...

38User Manual - Advanced setupCR series
User Manual - Advanced setup
6.3 Using dual head input
For extended flexibility to connect high resolution sources with a pixel clock over 165 MHz, 
the projector is supporting a dual head input mode. In this mode the left and \
right half of the 
image can be connected to the DVI 1/DVI 2 or HDMI 1/HDMI 2 interfaces respectively  
(Figure 6-1).  
To enable this mode, go to the menu INSTALLATION > DUAL HEAD SETUP. Side-by-side is 
the only available option at this...

39
6.4 Multi-channel 3D synchronization
X-PORT DCC120 has advanced capabilities for handling synchronization of multiple projec-
tors in a 3D installation.
6.4.1 Synchronous frame sequential
A typical synchronous frame sequential 3D setup is shown in Figure 6-2.
 
Figure 6-2. Synchronous frame sequential 3D
In this case IGs are synchronized and 3D sync from the source is connected from the DIN 
connector on the IG to the BNC sync-in connector. The source 3D sync is then sent to every 
projector in the...

40User Manual - Advanced setupCR series
User Manual - Advanced setup
6.4.3 Synchronous side-by-side
Figure 6-3 illustrates a typical synchronous side-by-side 3D setup.
 
Figure 6-3. Synchronous side-by-side setup
Since the sources are synchronized in this setup, synchronization management is not re-
quired in the projector. The table below shows the recommended system settings.
SETTINGPROJECTOR 1PROJECTOR 2
3DSide-by-sideSide-by-side
3D L/R syncSourceSource
3D BNC sync-out signalNot used, but can be set...