Barco CR Series Projector User Manual

11
2.4.4 REMOTE CONTROL WARNING
Laser radiation class II product; wavelength 670nm; maximum output 1mW.
Remote control complies with applicable requirements of 21 CFR 1040.10 and 1040.11.
Remote control complies with applicable requirements of EN/IEC 60825-1/2007
Use of controls or adjustments, or performance of procedures other than those  
specified in the User Guide, may result in hazardous radiation exposure.
2.4.5 WARNING SYMBOLS
Here is a list of warning symbols found on the product lable(s):
READ...

12User’s Guide - Safety InstructionsCR series 
User Manual - Safety Instructions
2.6 WEEE INFORMATION
This product conforms to all requirements of the EU Directive on waste electrical and elec-
tronic equipment (WEEE). This product shall be recycled properly. It can be disassembled to 
facilitate proper recycling of it’s individual parts. This product is using projection lamps that 
shall be recycled properly. Consult your dealer or relevant public authority regarding drop-off 
points for collection of...

13
english   

15
3 What’s in the box?
The following components are standard delivery:
Projector
Power Cable (Country Dependent)
Remote Control
User Documentation
Additional accessories available for the projector:
DVI-cable
Please verify that you have all compoents upon unpacking the unit, and i\
ts contents. Check 
next page for additional accessories.
Please save packaging materials for future use, should it be necessary to ship the unit.
english   

16User Manual - What’s in the Box?CR series 
User Manual - What’s in the box?
english   

17
4 Getting to know the projector
4.1 Overview
A Lens 
B IR sensor 
C1 Ventilation - Air flow IN
C2 Ventilation - Air flow OUT
D  Lens release 
E  Power connector 
F Keypad 
G Connector panel 
H LCD 
I  Lamp lids* 
J Adjustable feet 
K Security lock 
L  Ceiling mount
Figure 4-1.  - Projector front view
Figure 4-2.  - Projector rear view
Figure 4-3. - Projector bottom view
*  Features in the user guide pictures/drawings may be  different from your projector depending on model/version.
* HBGC2BI
F
JJK
B...

18User’s Guide – Getting to know the projectorCR series
User Manual - Getting to know the projector
4.2 Indicators
System status indicators are located right of the keypad on the back of the projector. Figure 
4-4 shows the three status indicators – one for each lamp and one for the system statu\
s.
Figure 4-4. The lamp indicators
For the lamp indicators the following apply:
- PERMANENT GREEN LIGHT: The lamp is on and operating normally.
- PERMANENT YELLOW LIGHT: The lamp is off. The lamp may be disabled...

19
4.2.2 Keypad
The projector has an illuminated keypad on the back of the unit. Figure 4-5 shows the 
keypad.
Figure 4-5.  Projector keypad
The keypad is used to:
- navigate the menu system
- scroll the information in the LCD panel
- directly select input sources
- enter pin code (if enabled)
- power on/off
- adjust basic image functions
The keypad is illuminated for operation in dark environments. Available functions are 
illuminated in yellow while selected (active) functions are illuminated in green....

20User’s Guide – Getting to know the projectorCR series
User Manual - Getting to know the projector
4.3 Connectivity
he projector features a wide range of video inputs and command/control connectors.  
Figure 4-7 shows the connector panel.
Figure 4-7. Connector panel
A LAN: 10/100 Mbit Ethernet connector for command, control and software upgrade.
B RC INPUT: 3.5mm mini-jack connector. Allows connection of external IR receiver or 
wired remote control.
C TRIGGERS: 3.5mm mini-jack connector triggers. Used...