ATT System 25 Reference Manual

Remote Administration Interface
Remote Administration Interface
Description
This feature provides dial-up access to the system’s administration port, either for a standard
system administration terminal or for a PC running Advanced Administration software.
Both read and write capability is provided with access to all system translation and fault tables. A
remote administration terminal can perform the same functions as the on-premises SAT.
Remote Administration allows remote access to the system by...

Features and Services
Remote Initialization and Maintenance Service (RIMS)
Description
Remote Initialization and Maintenance Service (RIMS) provides an AT&T technician remote access
to System 25. Using the RIMS feature, the technician can do System 25 initialization, ongoing
administration, and maintenance.
The remote administrator can initialize translations after the system is installed. Unless a hardware
change is required, the remote administrator can do ongoing administration without having to...

Remote Initialization and Maintenance Service (RIMS)
2. If you have a special telephone line connected to your System 25 for Remote Administration,
do one of the following:
l Unplug the line when it is not being used.
l Install a switch in the line to turn it off when it is not being used.
l Install a security device, such as AT&T’s Remote Port Security Device.
In addition, keep the Remote Administration telephone number secret. Only give it to people
who need to know it, and impress upon them the need...

Features and Services
2-278b
This page intentionally left blank.
November 1995 

Repertory Dialing
Repertory Dialing
Description
This feature allows multiline voice terminal users to store a telephone number, account code,
or feature access code in the system’s memory and associate that number with a REP DIAL
button. Pressing REP DIAL is equivalent to dialing the stored number. Individual numbers
can be up to 28 digits in length.
Programming the number is accomplished from the user’s voice terminal. Programming
procedures and other information can be found in the “Program” feature...

FEATURES AND SERVICES
Display: When a call is placed by pressing a REP DIAL button, the characters stored are
displayed. If V was programmed to store a pause, P is displayed in the position of the V .
If V was stored by programming # V , only V is displayed.If the button is not programmed,
REP DIAL is displayed.
Following/Forwarding: The associated activation and deactivation sequences (or portions of
them) can be stored on REP DIAL buttons.
Last Number Dialed: A number called by pressing a REP DIAL...

Send All Calls
Send All Calls
Description
This feature allows multiline voice terminal including ATL cordless telephone users to turn off
their ringers and invoke a“do not disturb” condition toward incoming calls. In addition,
users who have coverage or bridged appearances will have those calls directed immediately
to their covering and/or bridging stations, without the normal system ringing delay. Send All
Calls also allows covering users to temporarily remove their voice terminals from the
coverage...

FEATURES AND SERVICES
Interactions
The following features interact with Send All Calls.
Bridging of System Access Buttons:The principal station can be administered so that
pressing the SEND ALL CALLS button will send ringing for incoming calls to its coverage
stations only, to its bridging stations only, or to both.
If ringing is sent to a Bridged Access (BA) button via Send All Calls, and if the BA button is
administered to not receive ringing, the call will flash (but not ring) at the BA button. If...

Send All Calls
Hands-Free Answer on Intercom: Activating Send All Calls will cause an active AUTO ANS
button to turn off. As long as the Send All Calls feature is in use, AUTO ANS cannot be
turned on.
Line Status Indications:The line status lights still flash for incoming calls when Send All
Calls is in effect even though normal ringing is cut off.The lights stop flashing when the
calls are answered by a covering station or dropped by the caller.
Personal Line:Ringing on Personal Lines is turned off by...

FEATURES AND SERVICES
Speaker
Description
Some 7300H-series voice terminals have a built-in loudspeaker that allows on-hook dialing,
group listening, and monitoring of call progress signals. The terminal user turns on the
speaker by pressing the SPEAKER button.Pressing the button at an idle terminal has the
same effect as lifting the handset: the user is connected to the selected line and hears Dial
Tone. An associated LED is lighted when the Speaker is on. Speaker volume may be
adjusted by the...