AT&T Inidv2 I3812v Urer Guide

57
Working with the Power Supply Unit
The iPSU needs no scheduled maintenance other than regular batter y inspection and replacement. If the 
power supply unit is equipped with a backup batter y, it continues to provide voice-over-IP services in case of 
emergency during a power outage. During a temporary AC power outage, the power source is switched to 
the batter y without interruption of the voice-over-IP service. When the AC power is restored, the power 
source is switched back to the power supply...

iNID -- i3812V User Guide
58
Replacing the Battery
The batter y is rated for a service life of up to five years, which varies depending on operational and 
environmental conditions. The battery life expectancy depends on the operating environment as 
temperature extremes shorten the batter y life. The optimum operating temperature is between 
–5
o C to +50o C, ambient (23.0o F to 122o F). 
The batter y is specifically designed to use with the iNID system. Contact your ser vice provider for battery...

Working with the Power Supply Unit
59
Figure 12: Battery Connector 
4.
Release the safety strap securing the batter y.
5.Remove the old battery from the housing and put it safely aside. 
6.Insert the new batter y gently into the housing. 
7.Connect the battery cable connector to the batter y cable. 
8.Obser ve the BATTERY indicator on the iPSU, it should light green when the i38HG and i3812V are 
communicating properly. 
9.Secure the battery with the safety strap.
Note: Be careful when removing the...

iNID -- i3812V User Guide
60
10.Place the housing cover over the unit and press gently on it until it snaps into place.
11.Fasten the cover with the two screws you removed earlier. 
Note: If you have disabled the alert earlier, make sure to enable the aler t 
(page 63).  

Working with the Power Supply Unit
61
Disabling the Alert 
By default, the audible aler t is enabled to warn you when the battery is exhausted. It is recommended that 
you do not disable the audible aler t unless you intend to replace the batter y within a short time. A chirping 
tone sounds to aler t you that when the battery is exhausted and needs replacing. The duration of the 
chirping sound is 0.2 seconds and happens once ever y 5 seconds. You can turn off the chirping sound to 
disable the aler t...

iNID -- i3812V User Guide
62
2.Click Battery Info; the Emergency Batter y Backup page opens. 
3.Click Disable Aler t for 12 hours to turn off the low-batter y notification or deselect the Enable checkbox to 
disable the aler t permanently. 
4.Click Save.  

Working with the Power Supply Unit
63
Enabling the Alert 
To enable the aler t:
1.Enter http://gateway.2Wire.net as the URL; the Home page opens.  

iNID -- i3812V User Guide
64
2.Click Battery Info; the Emergency Batter y Backup page opens. 
3.Click Enable to enable the batter y audible aler t. 
4.Click Save.  

65
Configuring Services
There is no user-configuration needed for VoIP ser vice. All server and line configuration are performed by 
your ser vice provider. Refer to Table 5 in the Finding Solutions section if you encounter VoIP ser vices related 
issues. 
This section provides instructions to: 
 Set up Access control on page 66
 Configure Content screening on page 69
 Configure Web remote access on page 74 
 Access local network with Web remote access on page 76 

iNID -- i3812V User Guide
66
Setting up Access Control
The access control feature enables you to set restrictions on content access and time-of-day access for any 
device connected to your gateway. Access control can be set up for Web browsing, instant messaging, and 
other applications.
To configure time-of-day access: 
1.Open a Web browser and enter http://gateway.2Wire.net to access the 2Wire i3812V user interface. 
2.Click Ser vices and select Access Control; the Access Control page opens displaying...