Asus Router WL-320gE User Manual

							
3. Software
ASUS 802.11g Access Point1
Chapter 3 - Software Configuration
Home Gateway

LAN  to  WAN  filter  allows  you  to 
block  specified  packets  between 
LAN and WAN in a pre-defined time 
interval.  URL  filter  allows  you  to 
block specific URL access from your 
local network.
Note:  The  only  Ethernet  port  in 
ASUS  802.11g  AP  is  used  for 
WAN  connection  in  “Gateway” 
mode.  If  you  want  to  configure 
ASUS  802.11g  AP  through  an 
Ethernet  port,  remember  to  en-
able  “Web  Access  from  WAN” 
i n   “ I n t e r n e t   F i r e w a l l   -   B a s i c 
Config”.
3.10 Internet Firewall (in Home Gateway 
Mode)
3.11 System Setup
Click this item on the menu to reveal a sub menu. Follow the 
instructions  to  setup  the ASUS  802.11g AP.  Tips  are  given 
when you move your cursor over each item. 
						

							
3. Software
2ASUS 802.11g Access Point
Chapter 3 - Software Configuration
Web (Common)

3.11.1 Firmware Upgrade
This page reports the Flash Code (Firmware) version installed in the ASUS 
802.11g AP. Periodically, a new Flash Code is available for the ASUS 802.11g 
APs  on ASUS’s  Web  site. You  can  update  the ASUS  802.11g AP’s  Flash 
Code  using  the  Firmware  Upgrade  page  under  the Advanced  Setup  menu 
of  the Web  Manager.  If  you  are  experiencing  a  problem  with  your ASUS 
WLAN equipment, a Technical Support representative may ask you to give 
your device’s Flash Code (Firmware) version.
Note: The firmware upgrade takes approximately 60 to 90 seconds. 
When  the  firmware  upgrade  is  completed,  you  will  be  directed  to 
the home page.
3.11.2 SNMP (in AP mode)
Simple  Network  Management  Protocol  (SNMP)  is  a  popular  network 
monitoring  and  management  protocol.  It  allows  network  administrators 
to  monitor  the  status  of  the Access  Point  and  receive  notification  of  any 
critical  events  as  they  occur  on  the Access  Point.  You  can  set  up  the AP 
property for SNMP control in System Setup-> SNMP webpage, Click Save 
to  apply  your  change.  Install  the  SNMP  utility  and  the  MIB  file  provided 
in the utility CD. 
						

							
3. Software
ASUS 802.11g Access Point3
Chapter 3 - Software Configuration
Web (Common)

3.11.3 Setting Management
This function allows you to save current settings to a file, or load settings 
from a file. 
Save As a File 
Right-click on HERE link and select Save As... to save current setting into 
a file. 
Note: When current settings are saved to file, it will be saved to flash 
as well.
Load From a File 
Specify the path and name of the downloaded file in the New Setting File 
below. Then, click Upload. The upload process takes few minutes and then 
the system will reboot. 
New Setting File
Click Browse to locate the file. 
						

							
3. Software
ASUS 802.11g Access Point
Chapter 3 - Software Configuration
Web (Common)

3.11. Factory Default
Restoring Factory Default Settings
Web Manager
You can reset all settings to their factory default settings through the web 
manager using the “Factory Default” page in “Advanced Setup”. Click the 
Restore button and wait about 30 seconds before trying to access the ASUS 
802.11g AP.
Hardware
You can reset all settings to their factory defaults manually by pushing the 
“Reset” button of the ASUS 802.11g AP while it is ON. See page 21. Push 
the “Reset” button with a pen or a paper clip for about 5 seconds or until 
the power LED starts blinking.
Note: You will be notified when factory default settings are restored 
while using the web manager. 
						

							
3. Software
ASUS 802.11g Access Point
Chapter 3 - Software Configuration
Web (Common)

3.12 Status & Log
Click this item on the menu to reveal a sub menu. Follow the 
instructions  to  setup  the ASUS  802.11g AP.  Tips  are  given 
when you move your cursor over each item.
Status
System Up Time
It  shows  how  long  the ASUS  802.11g AP  has  been  running  since  the  last 
bootup.
Wireless 
						

							
. Troubleshooting
6ASUS 802.11g Access Point
Chapter  -Troubleshooting

. Troubleshooting
This  chapter  provides  you  with  troubleshooting  tips  and  solutions.  If 
problems still exist in your Access Point, contact Technical Support as listed 
on the front of this manual.
Common Problems and Solutions
Problem
The ASUS 802.11g AP does not power up:
Solution
•  Check  for  faulty  ASUS  802.11g  AP  power  supply  by  measuring  the 
output voltage with an electrical test meter.
•  Check failed AC supply (power outlet)
Problem
Cannot  communicate  with  other  ASUS  APs  through  a  wired  network 
connection.
Solution
•  Verify  network  configuration  by  ensuring  that  there  are  no  duplicate 
IP  addresses. Turn  off  the  device  in  question  and  ping  the  assigned  IP 
address of the device. Ensure no other device responds to that address.
• Check that the cables used have proper pin outs and connectors or use 
another LAN cable.
• Check that the hub, switch, or computer that the ASUS AP is connected 
and that all devices support 10Mbps speed.
This is what you will see if you connect the ASUS 802.11g AP to:
          10/100 Mbps Hub     Pure 100 Mbps Hub
Hub LED        ON           OFF 
Access Point (Link) LED   ON           ON
You will not know if the connection is bad from the ASUS AP Link LED 
alone, you will have to look at the Hub LED if you are not sure what kind 
of hub the ASUS AP is attached to. 
						

							
. Troubleshooting
ASUS 802.11g Access Point7
Chapter  -Troubleshooting

Problem
The  ASUS  8 0 2 . 11 g   AP  D e v i c e 
Discovery still cannot find or connect 
to  the ASUS AP  after  verifying  the 
IP address and LAN cable, changes 
cannot  be  made,  or  password  is 
lost.
Solution
In  case  the ASUS  802.11g AP  is  inaccessible,  you  can  restore  the ASUS 
802.11g AP’s factory default settings. Use a pen or paper clip to push the 
button for about five seconds or until the power LED starts blinking.
Reset to Defaults
Below is the factory default values of the ASUS 802.11g AP.
 
 Name              Default Value
Wireless - Interface
 SSID              default
 Channel              6
 Encryption (WEP)          None
 Broadcast SSID           No
Wireless - Bridge
 AP Mode              Access Point Only
Wireless - Access Control 
 MAC Access Mode          Disabled
IP Config - LAN 
 IP Address             192.168.1.1 
 Get IP Address Automatically       Yes 
 Subnet Mask            255.255.255.0 
 Gateway              (blank)
System Setup - Password
 Operation Mode          Access Point
 User Name            admin  
 Password              admin  
						

							
. Troubleshooting
8ASUS 802.11g Access Point
Chapter  -Troubleshooting

Problem
My ASUS WLAN Card will not associate with the ASUS 802.11g AP.
Solution
Follow these steps:
1.  Make sure that your WLAN Card and your WLAN Access Point have 
the same specifications.
2.  Try to bring the devices closer together; the ASUS WLAN Card may be 
out of range of the ASUS AP.
3.  Confirm  that  the  ASUS  AP  and  ASUS  WLAN  Card  have  the  same 
SSID.
4.  Confirm  that  the  ASUS  AP  and  ASUS  WLAN  Card  have  the  same 
Encryption settings, if enabled.
5.  Confirm that the ASUS AP’s Air and Link LEDs are solid green. 
6. Confirm  that  the  authorization  table  includes  the  MAC  address  of  the 
ASUS WLAN Card if “Authorization Table” is enabled.
7. Confirm that the operational mode is “Access Point” mode.
8. Confirm  that  the  ASUS  AP  and  ASUS  WLAN  Card  have  the  same 
preamble mode. 
Problem
The throughput seems slow.
Solution
To achieve maximum throughput, verify that your antennas are well-placed, 
not behind metal, and do not have too many obstacles between them. If you 
move the client closer to the ASUS AP and throughput increases, you may 
want to consider adding a second ASUS AP and implementing roaming.
• Check antenna, connectors and cabling.
• Verify network traffic does not exceed 37% of bandwidth.
• Check  to  see  that  the  wired  network  does  not  exceed  ten  broadcast 
messages per second.
• Verify wired network topology and configuration. 
						

							
. Troubleshooting
ASUS 802.11g Access Point
Chapter  -Troubleshooting

Problem
I cannot find the ASUS APs using the ASUS AP Discovery. 
Solution
To configure the ASUS AP through an ASUS WLAN Card, your computer 
must  be  in  the  same  subnet  of  the ASUS AP.  You  cannot  find  the ASUS 
APs  with  subnet  different  from  your  computer  within  the  same  gateway. 
You must change your computer to the same subnet as the ASUS AP. The 
factory default subnet of the ASUS AP is “192.168.1.1”.
Problem
How do I upgrade the firmware on the ASUS AP?
Solution
Periodically, a new Flash Code is available for the ASUS APs on the ftp site 
at ftp://ftp.asus.com. You can update the ASUS AP’s Flash Code using the 
software described in this User’s Manual. 
						

							
. Appendix
0ASUS 802.11g Access Point
Chapter  - Appendix

.  Appendix
Operating frequency range
The DSSS PHY shall operate in the frequency range of 2.4 GHz to 2.4835 
GHz as allocated by regulatory bodies in the USA and Europe or in the 2.471 
GHz to 2.497 GHz frequency band as allocated by regulatory authority in 
Japan.
Number of operating channels
The channel center frequencies and CH ID numbers shall be as shown below. 
The  FCC  (US),  IC  (Canada),  and  ETSI  (Europe)  specify  operation  from 
2.4 GHz to 2.4835 GHz. For Japan, operation is specified as 2.471 GHz to 
2.497 GHz. France allows operation from 2.4465 GHz to 2.4835 GHz, and 
Spain allows operation from 2.445 GHz to 2.475 GHz. For each supported 
regulatory domain, all channels marked with “Yes” shall be supported. 
In a multiple cell network topology, overlapping and/or adjacent cells using 
different  channels  can  operate  simultaneously  without  interference  if  the 
distance between the center frequencies is at least 30 MHz. Channel 14 shall 
be designated specifically for operation in Japan.