Asus Router WL-320gE User Manual

3. Software
ASUS 802.11g Access Point31
Chapter 3 - Software Configuration
Access Point

Channel
The  802.11g  and  802.11b  specifications  supports  up  to  14  overlapping 
channels for radio communication. To minimize interference, configure each 
ASUS  802.11g AP  to  be  non-overlapping;  select Auto  from  the  Channel 
drop-down list to enable the system to select a clear channel during boot up 
as your operating channel.
Based  on  your  site  survey  of  your  network  facility,  make  sure...

3. Software
32ASUS 802.11g Access Point
Chapter 3 - Software Configuration
Access Point

WPA Encryption
When  “WPA-PSK”  authentication  method  is  used,  the  newly  proposed 
TKIP  (Temporal  Key  Integrity  Protocol)  or AES  encryption  schemes  are 
applied.
WPA Pre-Shared Key
Select  “TKIP”  or  “AES”  in  the  WPA  Encryption,  this  field  is  used  as  a 
password to begin the encryption process. 8 to 63 characters are require\
d.
WEP Encryption
When  “Open  or  Shared  Key”,  “Shared  Key”...

3. Software
ASUS 802.11g Access Point33
Chapter 3 - Software Configuration
Access Point

Together these two schemes make a 128-bit (104 + 24) encryption scheme. 
Some vendors refer to this level of WEP as 104-bit and others refer to this 
as 128-bit. ASUS WLAN products use the term 128-bit when referring to 
this higher level of encryption.
Passphrase
Select  “WEP-64bits”  or  “WEP-128bits”  in  the  Encryption  field,  and  the 
Access Point generates four WEP keys automatically. A combination of up...

3. Software
3ASUS 802.11g Access Point
Chapter 3 - Software Configuration
Access Point

3.7.3  Access Control
Pull down menu items:
Disable (no info required)
Accept (need to input information)
Reject (need to input information)
3.7.2  Site Survey (AP SCAN)
Site Survey helps the Access Point associate appropriate AP while either in 
Station (Client) or URE (Repeater) mode. Make sure that the Access Point in 
Client or URE mode. Click “AP SCAN” button in Wireless -> Interface and 
a new window...

3. Software
ASUS 802.11g Access Point3
Chapter 3 - Software Configuration
Access Point

Note: Click the “Finish” button to save your new settings and restart 
the ASUS 802.11g AP or click “Save” and restart later.
Adding a MAC Address
The Known Client List collects MAC addresses of known clients, associated to 
the AP. To add a MAC address to the Access Control List, simply select MAC 
address from the list then click “Copy” button. 
3.7.  RADIUS Setting
Note: Click the “Finish” button to save...

3. Software
36ASUS 802.11g Access Point
Chapter 3 - Software Configuration
Access Point

3.7.  Multi-SSID
The Access  Point  works  with  a  primary  wireless  network  and  up  to  three 
Virtual  Local Area  Networks  (VLAN). You  must  first  enable  Multi-SSID 
and  VLAN  then  setup  each  VLAN  property.  Each  VLAN  works  with  its 
own VLAN ID and security level independently.
Note:  To  ensure  the  compatibility  of  various  client  card  while  site 
survey,  we  suggest  manually...

3. Software
ASUS 802.11g Access Point37
Chapter 3 - Software Configuration
Access Point

3.7.6  Advanced
This  section  allows  you  to  set  up 
additional parameters for the wireless 
router function. We recommend that 
you use the default values for all items 
in this window. 
You may also setup operation modes 
(AP or WDS, Station or URE) in this 
window aside from the Quick Setup 
screen.
Hide  SSID  -“No”  is  the  default  option  so  that  wireless  mobile  users  can 
see your ASUS 802.11g AP’s...

3. Software
38ASUS 802.11g Access Point
Chapter 3 - Software Configuration
Access Point

DTIM Interval (1-255) – DTIM (Delivery Traffic Indication Message) is 
a wireless message used to inform clients in Power Saving Mode when the 
system should wake up to receive broadcast and multicast messages. Type 
the time interval in which the system will broadcast a DTIM for clients in 
Power Saving Mode. The default value (3) is recommended
Beacon  Interval  (1-65535) –  This  field  indicates  the  time...

3. Software
ASUS 802.11g Access Point3
Chapter 3 - Software Configuration
Access Point

3.8  IP Config
Click this item on the menu to reveal a sub menu. Follow the 
instructions  to  setup  the ASUS  802.11g AP.  Tips  are  given 
when you move your cursor over each item.
LAN
Get IP Automatically
Select  Yes  (default)  or  No  to  get  IP  address  automatically  from  a  DHCP 
server. 
Yes
This  parameter  determines  if  the  ASUS  802.11g  AP  sends  out  a  DHCP 
request during bootup. If you...

3. Software
0ASUS 802.11g Access Point
Chapter 3 - Software Configuration
Home Gateway

Virtual  Server  allows  you  to  make 
services, like WWW, FTP, provided 
by  a  server  in  your  local  network 
accessible  for  outside  users.  DDNS 
allows users to export host names to 
the Internet through a DDNS service 
provider.  Each  time  your  ASUS 
802.11g  AP  connects  to  the  Internet 
and  gets  an  IP  address  from  an  ISP, 
this  function  will  update  your  IP 
address to the DDNS...