ASK Impression 860 User Guide

USER GUIDELCD PROJECTOR30SYMPTOMSOLUTIONSome colors are
unstable or
flickering· Check first that there are no loose cable
connections.
· You can try to adjust the image quality with the
CONTRAST and BRIGHTNESS keys.
· Try to improve the tuning using the TUNE key.The whole
image appears
to be unstable
or misplaced· Press SCALE to return to the default mode.
· Adjust the frequency and tuning settings
(instability), or the image position settings
(misalignment).
· Check that you are using a source with...

USER GUIDELCD PROJECTOR31 10 MAINTENANCE
10.1 GENERAL
From time to time, the LCD projector unit and lens may be cleaned with
a damp, non-abrasive cloth to remove dust and dirt spots.  The lens
should be cleaned with a mild dish-washing detergent solution, or with
standard lens cleaning solutions available from a photographic dealer.Do not scratch the lens surface and use the lens cap for
added protection when the projector is not in use. Remember
to remove the lens-cap when the LCD projector is in...

USER GUIDELCD PROJECTOR32 10.3 LAMP REPLACEMENT MESSAGES
When the time is due to replace the lamp, the projector will give you one
of the two following messages on the screen.
WARNING!
Lamp has less than 50 hours left of recommended burning time
Please change lamp!
Press any key to clear this message...
The lamp has only 50 hours burning time left, and should be changed.
Remember that you can check accumulated lamp usage each time the
projector is switched on. A message appears in the lower left hand...

USER GUIDELCD PROJECTOR33 If the lamp timer is accidentally reset before the lamp has reached
expected lifetime, or the lamp is changed before it is required and reset
the timer, the warning below appears. This leaves you with two
alternatives which are both described in the next paragraphs.
WARNING!
The lamp change indicator has been activated,
though the lamp has not reached expected lifetime.
Press RESET to confirm lamp change,
or press any other key to continue...
If the lamp has been  changed on...

USER GUIDELCD PROJECTOR34 10.4 FUSE REPLACEMENT
The mains fuse is located at the mains input, as an integral part of the
connector and switch assembly (See the figure).A defective fuse may indicate a permanent electrical failure. If
a new fuse breaks immediately, please return the unit to you
dealer for control.Release the fuse holder and replace the broken fuse with a new one.
Make sure to use a fuse of correct rating, see Technical Data section.
There is room for a spare fuse in the holder. 

USER GUIDELCD PROJECTOR35 10.5 CARE OF THE REMOTE CONTROL
The infrared remote control requires no maintenance, other than battery
replacement when required.  To change the batteries, open the battery
holder on the rear of the handset.  Remove the old batteries and dispose
of carefully.  Insert two new batteries of the type described in the
Technical Data section, observing the polarity instructions inside the
battery holder, and close the clip-shut door. Test that the remote control
functions correctly...

USER GUIDELCD PROJECTOR36 11 TECHNICAL DATAThe technical data given in this section was correct at the
time of going to print, but may change without prior notice in
order to improve product performance.This LCD projector is designed for indoor use and should not be
operated or stored in conditions outside the general environmental limits
given in section below, as this may lead to permanent damage and will
violate any warranties.
11.1 GENERAL ENVIRONMENTAL LIMITS
Storage temperature
-20 - 60°C (-4 - 140...

USER GUIDELCD PROJECTOR37 11.2 LCD PROJECTOR UNIT
PROJECTOR DIMENSIONS322 x 245 x 638mm/12.7 x 9.6 x
25.1 inchesPROJECTOR WEIGHT13.3 kg/29 lbsPROJECTION LENS303 - 335 mm VARIOFOCUSANTI-KEYSTONE CORRECTION8 degreesPROJECTION LAMP575W Dual ended metal halide
OSRAM 575W/GSLIGHT OUTPUT500 ANSI lumens
650 peak lumens
1350 peak luxLCD CELLActive matrix TFT (thin film
transistor) stripe configurationCOLOR RESOLUTION16.7 millionRESPONSE TIME30 msCONTRAST RATIO100:1PIXEL RESOLUTION800 x 600 x 3 (RGB)LCD SCREEN...

USER GUIDELCD PROJECTOR38 11.4 REMOTE CONTROL
UNIT SIZE153 x 56 x 15 mm / 6.0 x 2.1 x 0.6UNIT WEIGHT90 g / 3.2 ounzes (with batteries)BATTERIES2 x LR03/AAA 1.5V penlightFUNCTIONAL RANGE7 m / 23 feetCOMPATIBILITYMicrosoft 2-key serial; MAC; PS/2APPROVALSCE, FCC Part A11.5 COMPATIBILITY
The LCD projector is compatible with the interfaces and resolutions
shown below, some of which are predefined.  However since different
varieties of these exist, a frequency adjustment may be needed.MODERESOLUTIONMAXIMUM...

USER GUIDELCD PROJECTOR39 11.6 CONNECTORS ON THE SUPPLIED CABLES
The connectors on the supplied cables are described below.CABLEPROJECTORSOURCE ENDEND12 (if applies)VGA 4m/13ft Y-
split cable26 pin HDDSUB
male with
fingerscrewsComputer end:
15 pin HDDSUB
male with
fingerscrewsMonitor end:
15 pin
HDDSUB
female with
nutsMouse cable8 pin mini DIN
male8 pin mini DIN
male-Mouse adapter
cable (serial)8 pin mini DIN
femaleComputer end:
9 pin DSUB
female with
fingerscrewsMouse end: 9
pin DSUB
male with nutsMAC...