Home > Apple > Personal Computer > Apple power mac g4 fw 800 User Manual

Apple power mac g4 fw 800 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Apple power mac g4 fw 800 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							
     © 2003 Apple Computer, Inc. All rights reserved. 
    
     
     
     
    Service Source
     
    Power Mac G4 (Mirrored Drive Doors)Power Mac G4 (FW 800)
     
    Updated 22 February 2006 
    						
    							 
    © 2003 Apple Computer, Inc. All rights reserved.
     
    
     
     
     
    Service Source
    Take Apart
     
    Power Mac G4 (Mirrored Drive Doors)
    Power Mac G4 (FW 800) 
    						
    							 
    Power Mac G4 (Mirror/FW 800) Take Apart - 
     
    1
     
     General Information
     
    General Information
     
    Overview
     
    The identifying characteristics on the front of the Power Mac G4 (Mirrored Drive Doors), 
    Power Mac G4 (Mirrored Drive Doors 2003), and Power Mac G4 (FW 800) computers are 
    their top speaker and mirrored optical drive bezel. Like the Power Mac G4 (QuickSilver 
    and QuickSilver 2002) computers, these models also have a silver-colored case.
     The Power Mac G4 (Mirrored Drive Doors 2003) computer is identical to the Power Mac 
    G4 (Mirrored Drive Doors) computer except for updates to the drives and processor.
    The Power Mac G4 (FW 800) computer is similar to the Power Mac G4 (Mirrored Drive 
    Doors) computer with these exceptions:
    • FireWire 800 Mbps port 
    • AirPort Extreme Card option
    • Bluetooth option
    • SCSI card option is a third-party card; no Apple SCSI card option
    • SCSI cable is a third-party cable; no Apple SCSI cable 
    						
    							 
    2 - 
     
    Power Mac G4 (Mirror/FW 800) Take Apart
     General Information
     
    Important:
     
     The Take Apart procedures are the same for all versions of the computers 
    unless model differences are noted.
     
    Tools
     
    The following tools are required:
    • #2 Phillips screwdriver
    • #1 Phillips screwdriver
    • T-10 Torx driver or 2.5 mm Allen wrench
    • Small flat-blade screwdriver
    • Needlenose pliers
     
    Note:
     
      Magnetized tools are recommended to avoid dropping screws within the computer.
     
    Note:
     
      To organize the screws you remove from the computer, use a tray with divided 
    compartments (such as a plastic ice cube tray).
     
    Serial Number Location
     
    The computer’s serial number is located on the back panel.
     
    Before Opening the Computer
     
    Warning:
     
      The power supply in this computer is a high-voltage component and should not 
    be opened for any reason, even when the computer is off. 
     
    Warning:
     
     After shutting down the computer, you must wait a few minutes before servicing 
    it to allow internal components to cool.
     
    Important:
     
      The only way to shut off power completely to the computer and display is to 
    disconnect their power plugs from the power source. Make sure the power cords to the 
    computer and display are within easy reach. 
     
    Electrostatic Discharge (ESD) Precautions
     
    Follow these steps to avoid damage from ESD before working inside the computer. 
    1. Shut down the computer.
    2. Wait a few minutes to allow the computer’s internal components to cool.
    3. Unplug all cables from the computer except the power cord.
    4. Touch the metal PCI access covers on the back panel to discharge static electricity.
    5. Unplug the power cord.
    6. Lift the latch on the side of the computer. (If the latch will not lift, check that the 
    security lock port and lockable cover latch in the back of the computer are not locked.) 
    						
    							 
    Power Mac G4 (Mirror/FW 800) Take Apart - 
     
    3
     
     General Information7. Put on an ESD wrist strap. 
    8. To avoid static electricity building back up in your body, do not walk around the room 
    until after you have finished working and closed the computer.
     
    Operating the Computer
     
    Warning: In this computer the lower fan is in direct line with the heatsink. However, 
    when the computer is open and the side panel is set down, the fan and heatsink are 
    no longer in contact. To avoid overheating and permanent damage, never turn on 
    the computer unless all of its internal and external parts are in place and it is 
    closed. Operating the computer when it is open or missing parts can damage the 
    computer or cause injury. 
    						
    							 
    4 - 
     
    Power Mac G4 (Mirror/FW 800) Take Apart
     Opening the Computer
     
    Opening the Computer 
     
    Tools
     
    No tools are required for this procedure.
     
    Preliminary Steps
     
    No preliminary steps are required before you begin this procedure.
     
    Procedure
     
    1. Lift the latch to unlock the right side access panel.
    2.
     
    Note:
     
     Gently lower the side panel onto a clean, ESD-safe mat to avoid scratching the 
    case. Lower the side panel until it lies flat.
     
    Note:
     
     Release the latch before returning the side panel to its upright closed position. 
    						
    							 
    Power Mac G4 (Mirror/FW 800) Take Apart - 
     
    5
     
     Top Handles
     
    Top Handles
     
    Tools
     
    The only tool required for this procedure is a 2.5 mm Allen wrench.
     
    Part Location
    Preliminary Steps
     
    There are no preliminary steps for this procedure. 
    						
    							 
    6 - 
     
    Power Mac G4 (Mirror/FW 800) Take Apart
     Top Handles
     
    Procedure
     
    1. Remove the two Allen screws that secure the handle you are replacing.
    2. Lift the handle from the computer.
     
    Replacement Note:
     
     When replacing a handle, make sure the inner prongs fit inside the 
    raised points on the computer. 
    						
    							 
    Power Mac G4 (Mirror/FW 800) Take Apart - 
     
    7
     
     Top Handles
     
    Replacement Note:
     
     When replacing a handle, make sure you orient the handle so the 
    three tiny bumps are near the lower edge of the handle.The handle won’t fit properly if it is 
    turned upside down. The top front and top rear handles are interchangeable. 
    						
    							 
    8 - 
     
    Power Mac G4 (Mirror/FW 800) Take Apart
     Top Panel
     
    Top Panel
     
    Tools
     
    No tools are required for this procedure.
     
    Part Location
    Preliminary Steps
     
    Before you begin, remove the handles from the top front and top rear of the 
    computer. 
    						
    All Apple manuals Comments (0)

    Related Manuals for Apple power mac g4 fw 800 User Manual