Apple mac pro early 2009 User Manual
Have a look at the manual Apple mac pro early 2009 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 195 Apple manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Mac Pro (Early 2009) Take Apart — Processor Board, Quad Core 181 2010-09-27 Removal 1 Remove 9 screws. 2 Remove card from board. Reassembly Note: If you are installing new processor board, remove protective cap from new board’s processor holder and transfer cap to original board’s processor holder. Note that processor boards returned to Apple without protective caps may be rejected. Warning: Be careful not to touch gold pins in processor connector on board.
Mac Pro (Early 2009) Take Apart — Processor Tray Support Plate 182 2010-09-27 First Steps Open computer, lay it down with access side facing up, and remove: • Processor tray • Processor heatsink, Quad Core • Processor heatsink, 8 Core Note: Illustrations show Mac Pro (Early 2009) 8-core processor board. Procedure for quad-core processor configuration is the same. Support plate is identical for both configurations. Tools • ESD wrist strap • Phillips #2 screwdriver Processor Tray Support Plate
Mac Pro (Early 2009) Take Apart — Processor Tray Support Plate 183 2010-09-27 Removal 1 Remove 9 screws. 2 Remove support plate from board.
Mac Pro (Early 2009) Take Apart — Front-Panel-Board-to-Backplane-Board Cable 184 2010-09-27 First Steps Open computer, lay it down with access side facing up, and remove: • Hard drive and drive carrier in drive bay 1 • Graphics card in slot 1 • PCIe fan • Processor tray • Processor cage Tools • ESD wrist strap Front-Panel-Board-to- Backplane-Board Cable
Mac Pro (Early 2009) Take Apart — Front-Panel-Board-to-Backplane-Board Cable 185 2010-09-27 Removal 1 Disconnect cable from front panel board and backplane board. 2 Remove cable from enclosure.
Mac Pro (Early 2009) Take Apart — Backplane Board 186 2010-09-27 First Steps Open computer, lay it down with access side facing up, and remove: • All hard drives and drive carriers • Optical drive carrier and optical drives • PCIe fan • All PCI Express cards • Processor tray • Processor cage • Front-panel-board- to-backplane-board cable Disconnect power supply cable from backplane board. Refer to Power Supply in Take Apart. In addition, disconnect the antenna wires from the following (if installed): • AirPort Card • Bluetooth card Tools • ESD wrist strap • Phillips #2 screwdriver Backplane Board
Mac Pro (Early 2009) Take Apart — Backplane Board 187 2010-09-27 Removal 1 Disconnect 4 cables. 2 Remove 10 screws. 3 Release AirPort antenna wires from 1 clip on backplane board. 4 Release Bluetooth antenna wire from 2 clips on backplane board.
Mac Pro (Early 2009) Take Apart — Backplane Board 188 2010-09-27 5 Slide board down so that its power connector clears media shelf. 6 Slide board toward front of computer, so that its ports clear openings in back panel. 7 Lift board out of enclosure. Note: If you are replacing backplane board with a new board, transfer back ports EMI shield from original board to replacement board. Also transfer PCI cards and AirPort card (if installed). You do not need to transfer Bluetooth card to new board; it comes with Bluetooth card already installed.
Mac Pro (Early 2009) Take Apart — Backplane Board 189 2010-09-27 Reassembly Note: Connect optical drive cable A to connector A on backplane board; connect optical drive cable B to connector B on backplane board
Mac Pro (Early 2009) Take Apart — Front Panel Board 190 2010-09-27 First Steps Open computer, lay it down with access side facing up, and remove: • Hard drive and drive carrier in drive bay 1 • Graphics card in slot 1 • PCIe fan • Processor tray • Processor cage • Front-panel-board- to-backplane-board cable Tools • ESD wrist strap • Phillips #2 screwdriver Front Panel Board