Home > Apple > Display > Apple cinema display 22 lcd User Manual

Apple cinema display 22 lcd User Manual

Here you can view all the pages of manual Apple cinema display 22 lcd User Manual. The Apple manuals for Display are available online for free. You can easily download all the documents as PDF.

Page 21

 
Apple Cinema Display 22 (ADC) Take Apart -  
19  
 Inverter Board 
Inverter Board 
 
Tools
 
This procedure requires the following tools:
• #2 Phillips screwdriver  
Preliminary Steps
 
Before you begin, do the following:
• Place the display face down on an ESD mat
• Remove the foot assembly and hinge cover
• Remove the rear cover
• Remove the front bezel.
• Disconnect the cable connector from the main board to the inverter board
• Disconnect the cable connector from the main board to the display...

Page 22

 
20 -  
Apple Cinema Display 22 (ADC) Take Apart
 Inverter Board 
Procedure
 
1. Disconnect the backlight bulb wire connectors from the inverter board.
2. Remove the three screws from the inverter shield.
3. The inverter shield has small catches inside that secure the inverter board. Pull back 
slightly on the sides of the shield to release the board. 
Replacement Note: 
 Make sure that the board is secured by the four catches on the 
shield.  

Page 23

 
Apple Cinema Display 22 (ADC) Take Apart -  
21 
 Display Panel 
Display Panel 
 
Tools
 
This procedure requires the following tools:
• #2 Phillips screwdriver
• nylon probe tool (922-5065) 
Preliminary Steps
 
Before you begin, do the following:
• Place the display face down on an ESD mat
• Remove the foot assembly and hinge cover
• Remove the rear cover
• Remove the front bezel.
• Disconnect the cable connector from the main board to the inverter board
• Disconnect the cable connector from the main...

Page 24

 
22 -  
Apple Cinema Display 22 (ADC) Take Apart
 Display Panel 
Procedure
 
1. Remove the two screws on the inverter board bracket and remove the bracket.
2. Use the nylon probe tool to carefully spread the securing clip and remove the power/
brightness switch cable. 
Replacement Note: 
 Install the inverter board bracket with the arrow up.  
Important: 
 The backlight bulbs must be returned with the display panel. 

Page 25

Apple Cinema Display 22 (ADC) Take Apart - 23
 Top Backlight Bulb
Top Backlight Bulb 
Tools
This procedure requires the following tools:
• jeweler’s #1 Phillips screwdriver
• white cotton gloves (to prevent fingerprints on the bulbs and reflector)
Part Location
Preliminary Steps
Before you begin, do the following:
• Place the display face down on an ESD mat
• Remove the foot assembly and hinge cover
• Remove the rear cover
• Remove the front bezel. 

Page 26

24 - Apple Cinema Display 22 (ADC) Take Apart
 Top Backlight Bulb
Procedure
1. Peel the gray Mylar tape back on the chassis to expose the backlight bulb wires. 
2. Disconnect the two top bulb wire connectors from the inverter board and peel back the 
tape to release the wires. 
3. Remove the bulb screw. 
4. Put on cotton gloves, then carefully slide the bulb tray out of the panel. 
Important: The bulbs are very fragile. Handle with care.
Note: The bulbs are interchangeable top and bottom.  

Page 27

Apple Cinema Display 22 (ADC) Take Apart - 25
 Bottom Backlight Bulb
Bottom Backlight Bulb 
Tools
This procedure requires the following tools:
• jeweler’s #1 Phillips screwdriver
• white cotton gloves (to prevent fingerprints on the bulbs and reflector)
Part Location 

Page 28

26 - Apple Cinema Display 22 (ADC) Take Apart
 Bottom Backlight Bulb
Preliminary Steps
Before you begin, do the following:
• Place the display face down on an ESD mat
• Remove the foot assembly and hinge cover
• Remove the rear cover
• Remove the front bezel.
• Disconnect the cable connector from the main board to the inverter board
• Disconnect the cable connector from the main board to the display panel
• Disconnect the cable connector from the ADC cable to the display panel
• Remove the chassis from...

Page 29

Apple Cinema Display 22 (ADC) Take Apart - 27
 Bottom Backlight Bulb
Procedure
1. Disconnect the two bottom bulb wire connectors from the inverter board and peel back 
the tape to release the wires.
2. Remove the bulb screw.
3. Put on cotton gloves, then carefully slide the bulb tray out of the panel. 
Important: The bulbs are very fragile. Handle with care.
Note: The bulbs are interchangeable top and bottom  

Page 30

© 2003 Apple Computer, Inc. All rights reserved.
 Service Source
Troubleshooting
Apple Cinema Display 22 LCD (ADC) 
Start reading Apple cinema display 22 lcd User Manual

Related Manuals for Apple cinema display 22 lcd User Manual

All Apple manuals