Apple cinema display 22 lcd User Manual

							 
© 2003 Apple Computer, Inc. All rights reserved. 
 
 
 
Service Source
 Apple Cinema Display 22 LCD
(ADC)
 
11 April 2003 
						

							 
© 2003 Apple Computer, Inc. All rights reserved. 
 
 
 
Service Source
Take Apart
 
Apple Cinema Display 22 LCD (ADC) 
						

							 
Apple Cinema Display 22 (ADC) Take Apart -   
1  
 Tools 
Tools 
 
The following tools are recommended for the take apart procedures.
• 2 mm hex key
• #2 Phillips screwdriver 
• jeweler’s #1 Phillips screwdriver
• ESD wriststrap and mat
• white cotton gloves (922-1592)
• nylon probe tool (922-5065)  
Important:  
 The display plastics, inside and out, retain fingerprints and can scratch easily. 
Be very careful with tools, lay the display and plastic parts only on a clean soft surface, 
and wear clean white cotton gloves when handling and servicing the display. 
						

							 
2 -  
Apple Cinema Display 22 (ADC) Take Apart
 Foot Assembly 
Foot Assembly 
 
Tools
 
This procedure requires the following tools:
• 2 mm hex key
• White gloves for handling plastics 
Part Location
Preliminary Steps
 
Before you begin, do the following:
• Place the display face down on an ESD mat or soft cloth   
Note:  
 Plastics are easily damaged. The white gloves prevent fingerprints. 
						

							 
Apple Cinema Display 22 (ADC) Take Apart -   
3  
 Foot Assembly 
Procedure
 
1. Remove three hex screws. 
2. Lift the foot off the hinge. 
3. The clear hinge cap may fall off the foot. If it doesn’t, remove it from the foot.
4. Pull the ADC (Apple Display Connector) cable through the opening in the foot to 
separate the foot and the cable.  
						

							 
4 -  
Apple Cinema Display 22 (ADC) Take Apart
 Rear Cover 
Rear Cover 
 
Tools
 
This procedure requires the following tools:
• 2 mm hex key
• White gloves for handling plastics 
Note: 
 Plastics are easily damaged. The white gloves prevent fingerprints. 
Part Location
Preliminary Steps
 
Before you begin, do the following:
• Place the display face down on an ESD mat
• Remove the foot assembly 
						

							 
Apple Cinema Display 22 (ADC) Take Apart -   
5  
 Rear Cover 
Procedure
 
1. Remove eighteen hex screws on the rear cover.
2. Lift the rear cover slightly and disconnect the power/brightness switch cable 
connector, shown below. Carefully pull the ADC cable through the rear cover. 
Note: 
  The power/brightness switch board is permanently attached to the rear cover 
and cannot be removed. 
Replacement Note: 
 Verify that the clear plastic USB cover is in place over the USB 
socket, and that the USB icon arrows point up. 
						

							 
6 -  
Apple Cinema Display 22 (ADC) Take Apart
 Hinge 
Hinge 
 
Tools
 
This procedure requires the following tools:
• #2 Phillips screwdriver  
Part Location
Preliminary Steps
 
Before you begin, do the following:
• Place the display face down on an ESD mat
• Remove the foot assembly
• Remove the rear cover 
						

							 
Apple Cinema Display 22 (ADC) Take Apart -   
7  
 Hinge 
Procedure
 
1. Remove four screws.  
Note:  
  Two of the screws are yellow. These screws are for the 
ADC cable. 
2. Pull the ADC cable out of the way and remove two more hinge screws.
3. Lift the hinge up and off the chassis. 
Replacement Note:  
The hinge has locators on it, so it seats correctly in the chassis.  
						

							 
8 -  
Apple Cinema Display 22 (ADC) Take Apart
 Main Board Shield 
Main Board Shield 
 
Tools
 
This procedure requires the following tools:
• #2 Phillips screwdriver  
Part Location
Preliminary Steps
 
Before you begin, do the following:
• Place the display face down on an ESD mat
• Remove the foot assembly and hinge cover
• Remove the rear cover