AOR CU8232 Remote Control Interface Instructions
Have a look at the manual AOR CU8232 Remote Control Interface Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 212 AOR manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 42
- 42 -
SS
Engage search mode - start search.
The SS command is used to start the search process from either the current or
specified search bank.
To start searching from the current search bank use the format SS[ï]
To start searching from a specified search bank use the format SSx[ï]
where
x = search bank A ~ J or a ~ j.
Related commands DD MR MS RX SG VF é ê
ST
Tuning step size.
The ST command is used in conjunction with several other commands to set the
tuning or search increment....](http://img.usermanuals.tech/thumb/5671/81812/w64_aor_cu8232-rs232-unit-for-ar8000-and-ar2700_manual-1_d-41.png "Page 42
- 42 -
SS
Engage search mode - start search.
The SS command is used to start the search process from either the current or
specified search bank.
To start searching from the current search bank use the format SS[ï]
To start searching from a specified search bank use the format SSx[ï]
where
x = search bank A ~ J or a ~ j.
Related commands DD MR MS RX SG VF é ê
ST
Tuning step size.
The ST command is used in conjunction with several other commands to set the
tuning or search increment....")
![Page 44
- 44 -
TM
Write text in conjunction with memory channel.
The TM command cannot be used on its own but is used in conjunction with the
MX command to write text comments into a memory channel. Up to 7 ASCII
characters or characters from the table (below) may be entered. Blank table
entries [ ] represent a blank space. Please refer to the MX command for full
details of use.
TMxxxxxxx Text write where xxxxxxx may be up to 7
characters in ASCII or character mode.
Entry is completed with a [ï]...](http://img.usermanuals.tech/thumb/5671/81812/w64_aor_cu8232-rs232-unit-for-ar8000-and-ar2700_manual-1_d-43.png "Page 44
- 44 -
TM
Write text in conjunction with memory channel.
The TM command cannot be used on its own but is used in conjunction with the
MX command to write text comments into a memory channel. Up to 7 ASCII
characters or characters from the table (below) may be entered. Blank table
entries [ ] represent a blank space. Please refer to the MX command for full
details of use.
TMxxxxxxx Text write where xxxxxxx may be up to 7
characters in ASCII or character mode.
Entry is completed with a [ï]...")
![Page 45
- 45 -
characters or characters from the table (see TM) may be entered. Blank table
entries [ ] represent a blank space.
TTxxxxxxx Text write where xxxxxxx may be up to 7
characters in ASCII or character mode. Entry is
completed with a [ï]
Related commands SE SR
VA V B
Check and change the receive frequency of VFOA or VFOB.
The VB and VB commands may be used to read the current frequency from
VFOA or VFOB and to write a new receive frequency. Both commands are used
in the same manner, VA...](http://img.usermanuals.tech/thumb/5671/81812/w64_aor_cu8232-rs232-unit-for-ar8000-and-ar2700_manual-1_d-44.png "Page 45
- 45 -
characters or characters from the table (see TM) may be entered. Blank table
entries [ ] represent a blank space.
TTxxxxxxx Text write where xxxxxxx may be up to 7
characters in ASCII or character mode. Entry is
completed with a [ï]
Related commands SE SR
VA V B
Check and change the receive frequency of VFOA or VFOB.
The VB and VB commands may be used to read the current frequency from
VFOA or VFOB and to write a new receive frequency. Both commands are used
in the same manner, VA...")
![Page 46
- 46 -
VF
Switch to 2VFO mode.
The VF command is used to place the receiver into 2VFO mode. The data from
the current VFO (A or B) is automatically reported.
Use the command VF[ï]
A typical response may be: VA0433040000_ST0200000_AU1_MD1_AT0
The date representing 2VFO mode, VFOA active, receive frequency 433.04 MHz,
20 kHz channel step, Automode ON, receive mode NFM, attenuator ON.
Another response may be (for VFOB):
VB0145080000_ST020000_AU1_MD1_AT0
Related commands DD MR MG MS SM SG SS VA...](http://img.usermanuals.tech/thumb/5671/81812/w64_aor_cu8232-rs232-unit-for-ar8000-and-ar2700_manual-1_d-45.png "Page 46
- 46 -
VF
Switch to 2VFO mode.
The VF command is used to place the receiver into 2VFO mode. The data from
the current VFO (A or B) is automatically reported.
Use the command VF[ï]
A typical response may be: VA0433040000_ST0200000_AU1_MD1_AT0
The date representing 2VFO mode, VFOA active, receive frequency 433.04 MHz,
20 kHz channel step, Automode ON, receive mode NFM, attenuator ON.
Another response may be (for VFOB):
VB0145080000_ST020000_AU1_MD1_AT0
Related commands DD MR MG MS SM SG SS VA...")
![Page 47
- 47 -
To check the current status use the format XB[ï]
The response will be XB0 = level scan OFF
XB1 ~ XB7 = level scan ON
To change the status of level scan ON / OFF use the format:
XBn[ï] where n = 0 level scan OFF
n = 1 ~ 7 level scan ON
for example SB3 means level scan set to
threshold 3
Related commands BM ML XA XD XM XO XP XQ
XD
Scan delay time.
The XD command is used to check and set the scan delay time.
To check the current setting use the format: XD[ï]
The...](http://img.usermanuals.tech/thumb/5671/81812/w64_aor_cu8232-rs232-unit-for-ar8000-and-ar2700_manual-1_d-46.png "Page 47
- 47 -
To check the current status use the format XB[ï]
The response will be XB0 = level scan OFF
XB1 ~ XB7 = level scan ON
To change the status of level scan ON / OFF use the format:
XBn[ï] where n = 0 level scan OFF
n = 1 ~ 7 level scan ON
for example SB3 means level scan set to
threshold 3
Related commands BM ML XA XD XM XO XP XQ
XD
Scan delay time.
The XD command is used to check and set the scan delay time.
To check the current setting use the format: XD[ï]
The...")
![Page 48
- 48 -
XM
Mode scan.
The XM command is used to check and set the options for MODE SCAN.
To check the current setting use the format: XM[ï]
The response will be: XM0 = WFM
XM1 = NFM
XM2 = A M
XM3 = USB
XM4 = LSB
XM5 = C W
XMF = ALL MODE (effectively scan mode off)
To change the setting of mode scan use the format: XMn[ï]
where:
n = 0 WFM
n = 1 NFM
n = 2 A M
n = 3 USB
n = 4 LSB
n = 5 C W
n = F OFF - ALL MODES will be scanned.
Related commands BM ML XA XB XD XO XP XQ...](http://img.usermanuals.tech/thumb/5671/81812/w64_aor_cu8232-rs232-unit-for-ar8000-and-ar2700_manual-1_d-47.png "Page 48
- 48 -
XM
Mode scan.
The XM command is used to check and set the options for MODE SCAN.
To check the current setting use the format: XM[ï]
The response will be: XM0 = WFM
XM1 = NFM
XM2 = A M
XM3 = USB
XM4 = LSB
XM5 = C W
XMF = ALL MODE (effectively scan mode off)
To change the setting of mode scan use the format: XMn[ï]
where:
n = 0 WFM
n = 1 NFM
n = 2 A M
n = 3 USB
n = 4 LSB
n = 5 C W
n = F OFF - ALL MODES will be scanned.
Related commands BM ML XA XB XD XO XP XQ...")
![Page 49
- 49 -
XP
Change free scan time in scan mode.
The XP command is used to review and change the setting of free scan time when
in scan mode.
To review the current setting use the command XP[ï]
The response will be in the format:
XPnn where nn = 01 ~ 99 free scan time in seconds
nn = 00 free scan mode OFF
Examples are: XP52 = free scan time of 52 seconds
XP00 = free scan mode OFF
To change the current setting of free scan mode use the format XPnn[ï]
where: nn = 01 ~ 99 free scan time in seconds...](http://img.usermanuals.tech/thumb/5671/81812/w64_aor_cu8232-rs232-unit-for-ar8000-and-ar2700_manual-1_d-48.png "Page 49
- 49 -
XP
Change free scan time in scan mode.
The XP command is used to review and change the setting of free scan time when
in scan mode.
To review the current setting use the command XP[ï]
The response will be in the format:
XPnn where nn = 01 ~ 99 free scan time in seconds
nn = 00 free scan mode OFF
Examples are: XP52 = free scan time of 52 seconds
XP00 = free scan mode OFF
To change the current setting of free scan mode use the format XPnn[ï]
where: nn = 01 ~ 99 free scan time in seconds...")
![Page 50
- 50 -
é ê
UP / DOWN arrows.
The é ê arrow commands have largely the same effect as the arrow keys
on the front panel of the AR8000 receiver. In VFO mode the frequency is
incremented upward or downward, in memory recall mode the next channel is
selected and in search/scan modes the direction of search/scan may be reversed.
The value for é is h1E (HEX DECIMAL) and the command may be sent
using the format é[ï]
The value for ê is h1F (HEX DECIMAL) and the command may be sent
using the format...](http://img.usermanuals.tech/thumb/5671/81812/w64_aor_cu8232-rs232-unit-for-ar8000-and-ar2700_manual-1_d-49.png "Page 50
- 50 -
é ê
UP / DOWN arrows.
The é ê arrow commands have largely the same effect as the arrow keys
on the front panel of the AR8000 receiver. In VFO mode the frequency is
incremented upward or downward, in memory recall mode the next channel is
selected and in search/scan modes the direction of search/scan may be reversed.
The value for é is h1E (HEX DECIMAL) and the command may be sent
using the format é[ï]
The value for ê is h1F (HEX DECIMAL) and the command may be sent
using the format...")
- 51 - * IBM PC compatible specialist software for the AR8000- CU8232 & Microsoft WINDOWS will be available soon Optional software
- 52 - AOR, LTD 2-4-6 Misuji, Taito-ku, Tokyo 111, Japan TEL (03) 3865 1681 © Copyright AOR, LTD 1994 9409 TM