AOC V27m Operation Instructions

 11 
 LCD Monitor On or Off 
e monitor. Press the power button on the control 
panel, and the indicator lig . After a few seconds the monitor 
will be operating normally. 
Turning the
 
1. To turn on:   
Connect the AC power to th
ht will turn blue
 
 the control panel, to turn the monitor off. 
 
②.  the light will be orange. 
③. In power-off mode, the monitor indicator light will flash blue three times  and then go off. 
 
2. To turn off: 
Press the power button on
3. Indicator status: 
①. In normal...

 
Control Pa
12 
nel and Interface 
Side panel 
 
 
 
Signal Source: Press button to enter the interface of signal source  
Menu: Press to enter or exit the menu. 
▲  ▼ : When the menu appears on the screen, use these two 
buttons to select the desired option. 
Volume: With the menu displayed on the screen, press these two 
buttons to select the desired option. When no OSD 
menu is displayed on the screen, the controls will adjust 
sound volume. 
Volume +  
Volume - 
Menu 
Source 
selections and press...

 
Source Interface 
13 
   
to 
rned off. 
When co ector 
with the s
A device with multiple sources can be 
connected to your monitor. The figure 
below shows how to connect.
Tip: If you want to wall mount your monitor, all cables must be connected 
the monitor connectors first. 
Whenever an external device is connected to your monitor, please make 
sure the monitor is tu
nnecting an external device, connect the cable to the conn
ame color. 
 
 
PC Signal and   
PC Audio Input Component Input
Earphone...

 
Source Interface 
Video/S-Video Input: 
Connect the Video or S-Video cable to  the DVD player, CD player, Video 
Recorder, or Camcorder, etc. 
14  puter, DVD player, CD 
player, Video Recorder, or Camcorder) to the Audio Input connector. 
Audio Input: Connect the audio sources (e.g., com
Tip: Audio is shared between S-Video and Video. 
 
 
 
 

 
Source Interface 
15 
 auxiliary source audio and video (e.g., computer, DVD player, 
Auxiliary Component Input: 
Connect the
CD player, Video Recorder, or Camcorder) to the Component Input 
connector. 
 
 
 
 
HDMI Input: 
Connect the HDMI source (e.g., computer, DVD player, CD player, Video 
Recorder, or Camcorder) to the HDMI Input connector. 
 
 
 

 
Source Interface 
16 ctor on the back of the monitor with a 
A cable. Also connect the audio ca ble between PC Audio Input of the 
udio connector. 
PC Signal and PC Audio Input: 
Connect the PC to the PC input conne
VG
monitor and the PC a
 
Earphone Jack: 
Earphones can be connected to the Earphone jack. 
 
 

 
Using the Menu 
17 
sing the 
VOL Up key. Enable or adjust the 
own key. The selected 
option will be highlighted. 
u button again to exit the menu. 
ress Source button to enter the S ource menu, including PC, HDMI, Video, 
video, Component. 
 
  1.   Press the Menu button to display the menu. 
2.  Select the menu option to be adjusted using the Up or Down key. 
3.  Enter the submenu by pres fu nction selected by pressing the VOL Up and D 4.  Press the Men
 
Source Menu 
P
S-
 
 
 

 
Using the Men
18 
u 
Video Settings 
 
  etween 0 and 100. 
n  e 
e settings: Normal, 
DNR  not available in PC mode. 
 Mode  tandard, Vivid, and 
DCR  Enable/disable Dynamic Contrast Ratio. 
Reset  Restore the video settings to factory mode. 
BrightnessThis adjusts the brightness of the screen backlight. The 
adjustment range is b
Contrast This adjusts the screen co ntrast. The adjustment range is 
between 0 and 100. 
This adjusts the scree
Color Saturation color intensity. The adjustment rang
is...

 
Using the Menu 
Audio Settings (applicable to all modes) 
 uality 
Treble 
Equalizer   decrease until it 
, the sound from the left 
channel will gradually decrease until it disappears. 
Reset  Restore the audio se ttings to factory mode. Sound QSwitches between the five audio modes. 
Bass This is used to adjust the bass strength. 
This is used to adj ust the treble strength. 
The sound adjustment range is  0 to 60. During adjustment from 30 
adually
to 0, the sound from the right c hannel will gr...

 
Using the Menu 
Function settings 
 
Menu Language  sets the language used for the OSD. There are 24 
ble languages including English and Simplified Chinese.
Aspect Ratio 
tions 
ency 
conds) of the OSD menu. 
aving 
Power-On Recall:  Enable/disable Power-On Recall. 
Reset  Restores function settings to the factory default. This 
availa
4:3 
16:9 
Movie (This control is not available in PC mode.) 
Panorama (This contr
ol is not available in PC mode.) 
This sets the interval  before your monitor will...