AOC Lc32w063 User Manual

10
Controls & Connections:
SpeakerSpeaker
Power Indicator IR Receiver Volume +
Volume -
Channel
Channel
Menu
Input
Power
1.
VOL +  Press to increase the sound volume level.
2. VOL - Press to decrease the sound volume level.
3. CH ▲ Press to select the next higher program number.
4. CH ▼ Press to select the next lower program number.
5. MENU Press to open or exit the OSD (on-screen display) 
menu.
6. INPUT Press to select the input source.
7.
 Power Press to turn on / off (standby) the TV set. (Press 
to...

11
Buttons located at the right side of the TV will operate the same as the\
se buttons on the remote control. 
 
MTS
CC
PR E CH
Dis p la y
E PGW id e
A dd Fav
COMP
F avM U
/ E xit
E
N
Button description
POWERPress to turn on and off the TV.
COMPTV/ AV/ 
COMP/ HDMI/
PCPress TV, AV, COMP
 or HDMI/PC separately to select the input directly. 
PR
0-9  Press 0-9 to select a channel; the channel changes after two seconds. 
 
P R E CHPRE CH Press to go back to the previous TV channel or exit from the OSD when...

12
Set-Up 
Inserting Batteries into the remote control 
Insert two size AAA batteries (supplied) to the diagram inside the bat\
tery compartment of the remote control. 
attaching the Base
ImporTanT: The Base of the AOC LCD TV must be assembled prior to usage.
1. Place the TV set facing down on a soft and flat surface (blanket, foam,\
 cloth, etc.) to prevent any 
damage to TV set.   
2.  Carefully align and insert the Base to the stand
3.  Insert the screws to the bottom of the base and use them to...

13
Connecting TV 
Cable System or Vhf/Uhf antenna System 
You can enjoy standard-definition and high-definition digital programmin\
g (if available in your area), along with standard-definition analog 
programming. 
This TV is capable of receiving unscrambled digital programming for both\
 cable and external VHF/UHF antenna. 
It is strongly recommended that you connect the antenna/cable input usin\
g a 75-ohm coaxial cable to receive optimum picture quality. A 300-ohm 
twin lead cable can be easily...

14
Composite/ S-Video Signal Connection
S-VIDEO
S-VIDEOS-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO AV
AV IN 1
AV IN 1 / 2
Audio
pC Connection
Use the TV as a monitor for your PC shown below with the HD15 to HD15 co\
nnection. This TV can also be connected to a PC with DVI or HDMI 
output. (Refer to the separate Quick Setup
 Guide.)
PC
D-SUB
VGA IN
	Connect the PC IN jack to the PC using the HD15- HD15 cable with ferrite\
 core (analog RGB) and audio cable.
	If the PC is connected to the TV and no signal has been...

15
pC Input Signal reference Chart 
After connecting the PC to the TV, set the output signal from the PC acc\
ording to the chart below. 
presetting pC mode
Standard  resolution  horizontal frequency (khz)  Vertical frequency (hz) 
VESA640 x 480 31.46959.94
VESA 800 x 600 37.87960.317
VESA 1024 x 768 48.36360.004
VESA 1360 x 768 47.7259.799
Video Input Signal reference Chart 
After connecting the video input to the TV, set the output signal from t\
he video input according to the chart below. 
presetting...

16
USIng aoC TV
Turning the TV on and off
You can turn on the TV by using power switch button on the TV set or on \
the remote controller.
Navigate:Select:
OK
French
Spanish
English
Initial Wizard (1/8)
Please select language...
NextCancel
Initial Setting
When you first start up this AOC LCD TV set, please follow the Initial W\
izard to your AOC LCD TV.
1. Selecting language.
Select your preferred language:  English, Spanish or French
1Press ▲/▼ to select “Language”, and press oK.
2. Selecting Time...

17
a. Selecting Time Zone.
Inital Wizard (3/8)
Please select Time Zone...NSTMST
AST PST
EST AKST
CST HST
Navigate: Select:
OK
Previous
Cancel
1Press ▲/▼/◄/► to select “Time Zone” which you located then press oK.
 

18
B. manually enter the time.
Jan
2010
Year
1
Month
12:02 AM
Day
Time
OK
Previous Cancel
Navigate: Select:
OK
Initial Wizard (3/8)
Please enter the time...
year 
1Press ▲/▼ to select “Year” then press “OK”
2
Press ◄/► to adjust then press “OK”
month 
1Press ▲/▼to select “Month” then press “OK”
2
Press ◄/► to adjust then press “OK”
day 
1Press ▲/▼ to select “Day” then press “OK”
2
Press ◄/► to adjust then press “OK”
Time 
1Press ▲/▼ to select “Time” then press “OK”
2
Press ◄/► to select “Hour”, “Minute”...

19
3. Select “eco” mode or “Vivid” mode.
When you turn on TV in the first time, you can choose “Eco” mode to decrease backlight level to save the power consumption or “\
Vivid” mode to 
enhance picture contrast and sharpness.
ENTER
VividEco
Initial Wizard (4/8)
Please select Eco/Vivid mode...
Previous Cancel
Navigate: Select:
1Press ▲/▼ to select “Eco ” or “Vivid” for display setting.
4. Select TV rf tuning band 
CableAir
Initial Wizard (5/8)
Please select TV RF tuning band...
Previous Cancel
Navigate:...