AOC Lc32w063 User Manual

							10
Controls & Connections:
SpeakerSpeaker
Power Indicator IR Receiver Volume +
Volume -
Channel
Channel
Menu
Input
Power
1.
VOL +  Press to increase the sound volume level.
2. VOL - Press to decrease the sound volume level.
3. CH ▲ Press to select the next higher program number.
4. CH ▼ Press to select the next lower program number.
5. MENU Press to open or exit the OSD (on-screen display) 
menu.
6. INPUT Press to select the input source.
7.
 Power Press to turn on / off (standby) the TV set. (Press 
to turn on TV after the power on status, LED had 
changed to Blue.)
USB/
SERVICE
HDMI 3
AV IN 2
L-Audio-R out SPDIFHDMI In
PC In
AV in 1 L-Audio-R USB/Service
HDMI In
AV in 2 L-Audio-R
Headphone Jack
S-Video
Component In
VHF/UHF Cable In
Item description
Headphone Jack Connects to your headphones. If your headphones do not match the jack, u\
se a suitable plug adapter (not 
supplied). While headphones are connected, the TV speakers are muted.
L-AUDIO-R Out Connect an external sound system with standard audio cable to the AUDIO \
out (L/R) jacks on the back of your TV 
and to the AUDIO IN jacks on the amplifier. 
SPDIF
*
(Optical Digital Audio Out) Connect an external sound system with optical cable to the SPDIF
 out jack on the back of your TV to the SPDIF 
IN jack and to the amplifier or receiver.
AV IN 1/2 (AV/S-VIDEO)/L-
AUDIO-R  Connects to the COMPOSITE VIDEO output or S-Video output jack from your \
video equipment that has 
COMPOSITE or S-Video VIDEO, and audio (L/R) jacks can connect audio so\
urce to your TV. When connected, 
S-Video will take priority over Composite video (Yellow jack).
USB/Service Insert USB storage device to the USB2.0 port to view photos (JPEG only)\
.
S-VIDEO Input Connects to the S-VIDEO output jack on your camcorder or other video equipment that has S-VIDEO\
. The 
S-VIDEO provides better picture quality than composite video. The audio \
input connector was shared with 
COMPOSITE VIDEO IN.
HDMI IN 1/ 2/ 3 HDMI (High-Definition Multimedia Interface) provides an uncompressed, \
all-digital audio/video interface between 
this TV and any HDMI-equipped audio/video equipment, such as a set-top b\
ox, DVD player, Blu-ray Disc player, 
A/V receiver as well as PC. HDMI supports enhanced, or high-definition v\
ideo, plus digital audio. 
If the equipment has a DVI jack and not an HDMI jack, connect the DVI ja\
ck to the HDMI IN (with DVI-to-HDMI 
cable or adapter) jack, and connect the audio jack to the PC AUDIO IN j\
acks of HDMI IN. 
DVI-to-HDMI cable
DVI-to-HDMI adapter
HDMI connection is necessary to view 480i, 480p, 720p, 1080i and 1080p f\
ormats. 
Be sure to use only an HDMI cable that bears the HDMI logo. 
PC IN (RGB/AUDIO) Connects to a personal computer’s video output connector using HD15-H\
D15 cable (analog RGB). Can also be 
connected to other analog RGB equipment. See “PC Input Signal
 Reference Chart” on page 15 for the signals that 
can be displayed.
For some Apple Macintosh computers, it may be necessary to use an adapte\
r (not supplied). If this is the case, 
connect the adapter to the computer before connecting the HD15-HD15 cabl\
e. 
If the picture is noisy, flickering or not clear, adjust Phase  and Pitch of Screen settings. 
Component  IN 1/ 
2 (1080p/1080i/ 
720p/480p/480i)/ 
L-AUDIO-R Connects to your TV’s component video (YPbPr
 ) and audio (L/R) jacks. Component video provides better picture 
quality than the S-VIDEO or the composite video connections. Component video (YPbPr) connectio\
n is necessary 
to view 480i, 480p, 720p, 1080i and 1080p formats. 
VHF/UHF/Cable Input RF (Radio Frequency or modulated signal design used as the carrier for \
television broadcasts.) input that 
connects to your Cable or VHF/UHF antenna.
* SpdIfSony/Philips Digital Interconnect Format. S/PDIF is mostly used to trans\
mit compressed multichannel audio from a media player to an amplifier/re\
ceiver.
 
						

							11
Buttons located at the right side of the TV will operate the same as the\
se buttons on the remote control. 
 
MTS
CC
PR E CH
Dis p la y
E PGW id e
A dd Fav
COMP
F avM U
/ E xit
E
N
Button description
POWERPress to turn on and off the TV.
COMPTV/ AV/ 
COMP/ HDMI/
PCPress TV, AV, COMP
 or HDMI/PC separately to select the input directly. 
PR
0-9  Press 0-9 to select a channel; the channel changes after two seconds. 
 
P R E CHPRE CH Press to go back to the previous TV channel or exit from the OSD when 
displaying menu items and settings.
VOL +/-
Press to adjust the volume.
SOURCEPress to display the list of External Inputs. Press repeatedly to toggle\
 
through the inputs. 
MUTE
Press to mute the sound. Press again or press VOL + to restore the sound.
CH +/-Press to scan through channels. To scan quickly through channels, press \
and hold down either + or -.
 /  /  / Move left, up, down or right to select the available option or adjust th\
e 
setting in OSD menu. 
OK Press to confirm the selected item or setting.
MU
/ E xit
E
NMENU/EXIT Press to display or close a list of convenient functions and menu 
shortcuts. The OSD (On Screen Display) menu items vary based on input \
and content. 
D
is p la yDISPLAY  Press once to display the information pertaining to the channel and/or 
program when available. The OSD (On Screen Display) will time out in a\
 
few seconds or press again to immediately turn off the display. 
A
dd FavAdd Fav Press to add channel to Favorite List. 
FavFAV Channel Press to display the Favorite Channel List.
EPGEPG Press to display digital program guide in TV mode. It may show current 
channel name, program name, time, rating, and summaries, depending on 
the information provided by the broadcaster.
No function.
No function.
W
id eWIDE Press repeatedly to step through the Wide Mode settings: Normal Mode, 
Wide mode, Zoom 1 Mode and Zoom 2 Mode. 
PhotoPress to display the USB thumbnail browser. This is activated only if th\
e 
USB storage device is plugged into the USB hub.
Freeze
Press to freeze the displayed picture.
MTSMTS* Press to activate the NTSC TV sounds, such as: Stereo, SAP** or Mono 
tone and languages of DTV.
SLEEP*** Press repeatedly to cycle through the available sleep timer, 5, 10, 15, \
30, 
60, 90, 120 180 and 240 minutes to turn off TV automatically.
PICTUREPress repeatedly to cycle through the available picture modes: Vivid
, 
Standard, Eco, Movie and Personal. The picture modes can also be 
accessed in the Picture settings. For details, see section- Adjust Pictu\
re 
Setting. 
AUDIO Press repeatedly to cycle through the available sound modes: 
Music, 
Speech and Personal. The sound modes can also be accessed in the 
Sound  settings. For details, see section- Adjust Audio Setting.
V-Chip Press to lock Parental Control temporarily. (After setting the restrict\
ed 
table of MPAA, Motion Picture Association of America or TV Rating.)
C
CCC Press repeatedly to change the closed caption type as CC Off /
CC On / CC On With Mute.
* multichannel Television Sound (mTS
)The broadcasting standard, which allows stereo sounds to be transmitted \
with the TV picture.** Second audio program (Sap)Another or additional audio channel provided for in the Multichannel Tel\
evision Sound (MTS ) broadcast standard. A monaural sound track included within 
the recorded or video signal (usually containing a second language tran\
slation for the displayed program).
*** SleepYou can set a time period for which the TV will be turned off automatica\
lly.
 
						

							12
Set-Up 
Inserting Batteries into the remote control 
Insert two size AAA batteries (supplied) to the diagram inside the bat\
tery compartment of the remote control. 
attaching the Base
ImporTanT: The Base of the AOC LCD TV must be assembled prior to usage.
1. Place the TV set facing down on a soft and flat surface (blanket, foam,\
 cloth, etc.) to prevent any 
damage to TV set.   
2.  Carefully align and insert the Base to the stand
3.  Insert the screws to the bottom of the base and use them to tighten the \
base to the stand. 
4.  Please refer to the “Important Usage instructions” in the above.
Wall-mounting 
Please install on a wall by using a Wall-Mount Bracket (sold separately\
). Before mounting the TV on a wall, the Table-Top Stand must be 
removed from the TV.  Follow the simple steps below to remove the Table-\
Top Stand:
1. Disconnect all the cables from the TV.
2.  Gently lay the TV, face down, onto a level and stable surface covered wi\
th a thick and soft cloth. Make sure the Table-Top Stand is hanging 
over the edge. 
3.  Remove the screws as shown in the illustration for your model and pull t\
he Table-Top Stand out. 
4.  Do not remove any other screws from the TV. 
5.  Do not remove the Table-Top Stand for any reason other than to Wall-Moun\
t  the TV. 
6.  Be sure to store the removed screws and Table-Top Stand in a safe place \
until you are ready to reattach the Table-Top Stand. Keep the 
screws away from small children. 
7.  For bracket installation, refer to the instruction guide provided by the Wall-Mount  Bracket model for your TV. Sufficient expertise is required in 
installing this TV, especially to determine the strength of the wall for\
 withstanding the TV’s weight. 
8.  For product protection and safety reasons, AOC strongly recommends that \
you use the Wall-Mount  Bracket model designed for your TV and 
the Wall-Mounting of your TV should be performed by AOC dealer or licens\
ed contractor. 
M4 screw(4pcs)
1 23
Note: 200 mm x 200 mm wall mount bracket & M4 screws (Screws length: 10\
mm and pitch: 0.7mm) are not included.  Please contact your local 
distributor.
 
						

							13
Connecting TV 
Cable System or Vhf/Uhf antenna System 
You can enjoy standard-definition and high-definition digital programmin\
g (if available in your area), along with standard-definition analog 
programming. 
This TV is capable of receiving unscrambled digital programming for both\
 cable and external VHF/UHF antenna. 
It is strongly recommended that you connect the antenna/cable input usin\
g a 75-ohm coaxial cable to receive optimum picture quality. A 300-ohm 
twin lead cable can be easily affected by radio frequency interference, \
resulting in signal degradation. 
Cable or VHF/UHF(or VHF only)75-ohm coaxial
cable (supplled) Rear of TV
VHF/UHF input
TUNER
TUNERTUNER
high definition Interface
You can enjoy high-definition programming by subscribing to a high-defin\
ition cable service or a high-definition satellite service. For the best\
 
possible picture, make sure you connect this equipment to your TV via th\
e HDMI or component video (with audio) input on the back of your TV. 
hdmI Connection
HDMI HDMI
HDMI
HDMI
HD Multimedia Interface
HDMI IN 1 / 2 / 3
If the equipment has a DVI jack and not an HDMI jack, connect the DVI ja\
ck to the HDMI IN (with DVI-to-HDMI cable or adapter) jack and 
connect the audio jack to the PC AUDIO IN jacks.
Component Signal  Connection
LR YPb Pr
Y Pb Pr
Component Video Input
Component IN 1/2LR YPb Pr
LR YPb Pr
LR YPb Pr
LR YPb Pr
Audio
 
						

							14
Composite/ S-Video Signal Connection
S-VIDEO
S-VIDEOS-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO AV
AV IN 1
AV IN 1 / 2
Audio
pC Connection
Use the TV as a monitor for your PC shown below with the HD15 to HD15 co\
nnection. This TV can also be connected to a PC with DVI or HDMI 
output. (Refer to the separate Quick Setup
 Guide.)
PC
D-SUB
VGA IN
	Connect the PC IN jack to the PC using the HD15- HD15 cable with ferrite\
 core (analog RGB) and audio cable.
	If the PC is connected to the TV and no signal has been input from the P\
C for more than 30 seconds, the TV enters the standby mode 
automatically. 
external sound Connection
	Turn off the AOC LCD TV and Sound Device and connect the Audio Out jack \
or SPDIF  jack on the rear of AOC LCD TV.
	Connect an audio cable to the audio output connectors associated with th\
e Audio Out (R/L) and SPDIF on the TV Set and connect the other 
end to the audio connectors associated with the Audio input of the Exter\
nal Sound.
SPDIF
SPDIFSONY Philips Digital Interface
SPDIF INSPDIF
SPDIF
 
						

							15
pC Input Signal reference Chart 
After connecting the PC to the TV, set the output signal from the PC acc\
ording to the chart below. 
presetting pC mode
Standard  resolution  horizontal frequency (khz)  Vertical frequency (hz) 
VESA640 x 480 31.46959.94
VESA 800 x 600 37.87960.317
VESA 1024 x 768 48.36360.004
VESA 1360 x 768 47.7259.799
Video Input Signal reference Chart 
After connecting the video input to the TV, set the output signal from t\
he video input according to the chart below. 
presetting Video mode
Standard  resolution  horizontal frequency (khz)  Vertical frequency (hz) 
SD480i 15.734 60
SD 480P 31.5 60
SD 576i 15.625 50
SD 576P 31.25 50
HD 720P 37.5 50
HD 720P 4560
HD 1080i 28.125 50
HD 1080i 33.75 60
FHD 1080p 56.3 50
FHD 1080p 67.5 60
Standard definition Interface
You can also enjoy traditional program by using a DVD player or VCR Play\
er. Connect this equipment to your TV via the Composite Input or 
S-Video Input on the back of your TV. 
Refer to the Quick Setup Guide (supplied) when connecting other equipment to your TV.
 
						

							16
USIng aoC TV
Turning the TV on and off
You can turn on the TV by using power switch button on the TV set or on \
the remote controller.
Navigate:Select:
OK
French
Spanish
English
Initial Wizard (1/8)
Please select language...
NextCancel
Initial Setting
When you first start up this AOC LCD TV set, please follow the Initial W\
izard to your AOC LCD TV.
1. Selecting language.
Select your preferred language:  English, Spanish or French
1Press ▲/▼ to select “Language”, and press oK.
2. Selecting Time mode.
ManualAuto
Initial Wizard (2/8)
Please select Time mode...
Previous Cancel
Navigate: Select:
OK
1Press ▲/▼ to select “Auto” or “Manual” for Time Mode.
 
						

							17
a. Selecting Time Zone.
Inital Wizard (3/8)
Please select Time Zone...NSTMST
AST PST
EST AKST
CST HST
Navigate: Select:
OK
Previous
Cancel
1Press ▲/▼/◄/► to select “Time Zone” which you located then press oK.
 
						

							18
B. manually enter the time.
Jan
2010
Year
1
Month
12:02 AM
Day
Time
OK
Previous Cancel
Navigate: Select:
OK
Initial Wizard (3/8)
Please enter the time...
year 
1Press ▲/▼ to select “Year” then press “OK”
2
Press ◄/► to adjust then press “OK”
month 
1Press ▲/▼to select “Month” then press “OK”
2
Press ◄/► to adjust then press “OK”
day 
1Press ▲/▼ to select “Day” then press “OK”
2
Press ◄/► to adjust then press “OK”
Time 
1Press ▲/▼ to select “Time” then press “OK”
2
Press ◄/► to select “Hour”, “Minute” or “AM/PM” then press “OK”
3
Press ▲/▼ to adjust then press “OK”
 
						

							19
3. Select “eco” mode or “Vivid” mode.
When you turn on TV in the first time, you can choose “Eco” mode to decrease backlight level to save the power consumption or “\
Vivid” mode to 
enhance picture contrast and sharpness.
ENTER
VividEco
Initial Wizard (4/8)
Please select Eco/Vivid mode...
Previous Cancel
Navigate: Select:
1Press ▲/▼ to select “Eco ” or “Vivid” for display setting.
4. Select TV rf tuning band 
CableAir
Initial Wizard (5/8)
Please select TV RF tuning band...
Previous Cancel
Navigate: Select:
OK
1Press ▲/▼ to select “Air” or “Cable” for RF Tuning setting. Press “OK” will execute channel searching.